Lowe s A05268 LNC Gordios Matte LED Mini Hanging Kitchen Island Light Instruction Manual

June 15, 2024
Lowe s

Lowe s A05268 LNC Gordios Matte LED Mini Hanging Kitchen Island Light

Lowe s-A05268-LNC-Gordios-Matte-LED-Mini-Hanging-Kitchen-Island-Light-
product

Product Information

Specifications:

  • Item Number: A05268
  • Max Voltage: 120V
  • Max Wattage per Bulb: Type A, 60W

Product Usage Instructions

Installation:

  1. We suggest installation by a licensed electrician.
  2. Before starting installation, ensure the electricity is shut off.
  3. Ensure the mounting surface is clean, dry, flat, and strong enough to support the lamp.
  4. The mounting surface should be at least 1/4 larger than the canopy on all sides.
  5. Any gaps between the mounting surface and canopy exceeding 3/16 should be corrected.
  6. Make sure the ceiling or wall can withstand the weight of the lamp.

Safety Precautions:

  • Keep the lamp away from acidic and alkaline substances to prevent damage to the surface.
  • When replacing bulbs, turn off or unplug the lamp and wait until it cools down.
  • Common sense, caution, and care must be used with any electrical products.

Cleaning:

To clean the fixture, wipe it with a soft cloth. Clean glass with a mild cleaner such as mild and non-abrasive soap. Do not use abrasive materials like scouring pads, powders, steel wool, or  abrasive paper.

Tools Required:

  • Ladder
  • Philips Head or Flat Blade Screwdriver
  • Electrical Tape
  • Pliers
  • Wire Cutter/Stripper

Parts Included:

  • (C) Single bar (1)
  • (D) Green ground screw (1)
  • (E) Canopy (1)
  • (F) Collar ring (1)
  • (G) Collar loop (1)
  • (H) Quick link (2)
  • (I) Chain (1)
  • (J) Loop (1)
  • (K) Frame (1)
  • (L) Tray (1)
  • (M) Socket (1)
  • (N) Lampshade (1)
  • (O) Socket ring (1)

Accessories Enclosed:

  • (A) Wire connector (3)
  • (B) Mounting screw (2)

Assembly and Installation Instructions:

  1. Carefully remove the fixture from the carton and ensure all parts and accessories are included.
  2. Hang the lampshade (N) onto the tray (L), and screw the socket ring (O) to the socket (M) to secure them.
  3. Install the bulb (not included), ensuring it does not exceed the maximum wattage recommended on the socket.
  4. Use chain pliers to disconnect and discard any unwanted parts when reaching the top of the chain (I). Gently pull the wires to ensure they are not stressed.
  5. Turn off the power before starting the installation.
  6. Secure the canopy (E) in the proper position using the collar loop (G) and collar ring (F).
  7. Use the provided mounting screws (B) to mount the fixture to the prepared mounting surface.

FAQ:

  • Q: Where can I order replacement parts for this fixture?
    A: All parts for this fixture can be ordered from the place of purchase. Ensure you use the exact wording from the illustration when ordering parts.

Item Number :A05268

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
  4. Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
  5. Place the wall switch in the “OFF” position.
  6. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  7. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  8. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per blub.
  9. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  10. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  11. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products

IMAGE FOR FINISHED PRODUCT

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS REQUIRED (NOT INCLUDED):Lowe s-A05268-LNC-Gordios-Matte-LED-Mini-
Hanging-Kitchen-Island-Light-fig- \(2\)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDED

Lowe s-A05268-LNC-Gordios-Matte-LED-Mini-
Hanging-Kitchen-Island-Light-fig- \(3\)

  • (C) Single bar (1)
  • (D) Green ground screw (1)
  • (E) Canopy (1)
  • (F) Collar ring (1)
  • (G) Collar loop (1)
  • (H) Quick link (2)
  • (I) Chain (1)
  • (J) Loop (1)
  • (K) Frame (1)
  • (L) Tray (1)
  • (M) Socket (1)
  • (N) Lampshade (1)
  • (O) Socket ring (1)

ACCESSORIES & QTY ENCLOSED:

  • (A) Wire connector (3)
  • (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Make pre-installationLowe s-A05268-LNC-Gordios-Matte-LED-Mini-Hanging-Kitchen-Island-Light-fig- \(4\)

  3. Step A1 » Screw loop (J) to top of the frame (K) as shown in the illustration.

  4. Step A2»

  5. Remove socket ring (O) from socket (M).

  6. Carefully hang lampshade (N) onto tray (L), and then screw socket ring (O) to socket (M) to secure them When installing socket ring (O), please note the orientation of socket ring (O) is that the side of
    rolled edge faces upward as shown in the illustration.

  7. Install bulb (not included) (Please do not exceed the maximum wattage recommended on the socket.)Lowe s-A05268-LNC-Gordios-Matte-LED-Mini-Hanging-Kitchen-Island-Light-fig- \(5\)

  8. Step B1 » By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.

  9. Step B2 » Attach quick links (H) to chain (I) and loop (J) on the top of frame (K).

  10. Step B3 » Carefully weave the fixture wires through main chain (I) in and out of every other link and stop just when you reach the top of chain (I). Gently pull the wires to ensure the wires are not stressed.

  11. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

  12. Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.

  13. Place the wall switch in the “OFF” position.

  14. Make installationLowe s-A05268-LNC-Gordios-Matte-LED-Mini-Hanging-Kitchen-Island-Light-fig- \(6\)

  15. Step C1 » Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B).
    NOTE: the side of single bar (C) marked “GND” must face out.

  16. Step C2 » Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position. Unscrew collar ring (F) from collar loop (G) and remove canopy (E). Refer to the following note, you would know the proper position where collar loop (G) should be located.
    NOTE : canopy (E) should be snug against the ceiling and collar loop (G) should be screwed enough threads (no less than 6 threads) on the pre-assembled threaded nipple for more secure hanging.
    If not, adjust collar loop (G) on single bar (C) by screwing collar loop (G) in or out of single bar (C) until the secure length is achieved.

  17. Step C3 » Pass chain (I) through collar ring (F) and then through canopy (E).

  18. Step C4 » Open quick link (H), attach quick link (H) to collar loop (G). Close quick link (H).
    Pass the fixture wires through collar loop (G) to the top of the pre-assembled threaded nipple and gently pull to ensure the wires are not stressed

  19. Step C5 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above single bar (C) is at least 6″.

  20. Step C6 » Make wire connections
    Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
    Connect ground wires according to the chart below
    Connect wires according to the chart below
    Note:
    When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

  21. Twist wires together with plastic wire connectors (A) until tightly joined.

  22. Wrap each connector with approved electrical tape.

  23. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  24. Step C7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).

  25. Step C8 » Install bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

  26. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals