Lowe s A05241 Cartlann 3 Light Matte Black LED Dry Rated Chandelier Instruction Manual
- June 15, 2024
- Lowe s
Table of Contents
Lowe s A05241 Cartlann 3 Light Matte Black LED Dry Rated Chandelier
Product Information
Item Number: A05241
Specifications:
- Installation by a licensed electrician is recommended.
- Voltage: 120V
- Maximum wattage: Type A, Max 60W per bulb
Product Usage Instructions
Preparing for Installation
Before starting assembly and installation, please prepare the following tools:
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Assembly and Installation
Step 1: Checking Parts and Accessories
Carefully remove the fixture from the carton and check that all parts and
accessories are included as shown in the illustration.
Step 2: Removing Unwanted Parts
Using chain pliers, disconnect and discard any unwanted parts.
Step 3: Connecting Quick Link
Close the quick link (H) by screwing it until it is securely closed. Attach
one end of the chain (I) to the quick link.
Step 4: Turning Off Power
Before starting the installation, make sure to turn off the power. Never
attempt any work without shutting off the electricity until the work is done.
Step 5: Mounting the Fixture
Mount the fixture by attaching the single bar (C) to the mounting surface
using the provided mounting screws (B). Ensure that the side of the single bar
marked GND is facing out.
Step 6: Adjusting Canopy and Collar Loop
Ensure that the canopy (E) is snug against the ceiling and adjust the collar
loop (G) on the single bar (C) for more secure hanging. Screw the collar loop
(G) in or out of the single bar (C) until the desired secure length is
achieved.
Step 7: Wiring
Pass the fixture wires through the collar loop (G) to the top of the pre-
assembled threaded nipple. Make sure the wires are not stressed.
Step 8: Connecting Wires
Connect the wires according to the provided charts. Please note that the
ground wire is a bare copper wire and should only be connected to other ground
wires.
FAQ (Frequently Asked Questions)
-
Q: What is the maximum wattage for each bulb?
A: The maximum wattage for each bulb is 60W for Type A bulbs. -
Q: Can I install this fixture myself?
A: While it is possible to install the fixture yourself, we recommend installation by a licensed electrician for safety reasons. -
Q: Can I use a different voltage other than 120V?
A: No, this fixture is designed for use with a voltage of 120V. Using a different voltage may result in damage to the fixture or electrical hazards.
Item Number :A05241
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Ensure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS TYPE & QTY INCLUDED
- (C) Single bar (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Collar ring (1)
- (G) Collar loop (1)
- (H) Quick link (2)
- (I) Chain (1)
- (J) Loop (1)
- (K) Stem (1)
- (L) Frame (1)
- (M) Socket assembly (1)
ACCESSORIES & QTY ENCLOSED:
- (A) Wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Make pre-installation
-
Step A1 » By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.
-
Step A2 » Screw stem (K) onto socket assembly (M) as shown in the illustration.
-
Step A3 » Open quick link (H), and then attach quick link (H) to chain (I) and loop (J) on the top of stem (K). Close quick link (H).
-
Step A4 » Carefully weave the fixture wires through chain (I) in and out of every other link and stop just when you reach the top of chain (I). Gently pull the wires to ensure the wires are not stressed.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. -
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
-
Make installation
-
Step B1 » Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B).
Note: the side of single bar (C) marked “GND” must face out. -
Step B2 » Raise canopy (E) over collar loop (G) and screw collar ring (F) to measure a proper position
NOTE : canopy (E) should be snug against the ceiling and collar loop (G) should be screwed enough threads (no less than 6 threads) on the pre – assembled threaded nipple for more secure hanging. If not, adjust the collar loop (G) on single bar (C) by screwing collar loop (G) in or out of single bar (C) until the secure length is achieved. -
Step B3 » Pass chain (I) through collar ring (F) and then through canopy (E).
-
Step B4 » Open quick link (H), attach quick link (H) to collar loop (G). Close quick link (H). Pass the fixture wires through collar loop (G) to the top of the pre-assembled threaded nipple and gently pull to ensure the wires are not stressed.
-
Step B5 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above single bar (C) is at least 6″.
-
Step B6 » Make wire connections
Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the chart below
Connect wires according to the chart below
Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.) -
Twist wires together with plastic wire connectors until tightly joined.
-
Wrap each connector with approved electrical tape.
-
QBe sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
-
Step B 7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).
-
Step B8 » Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
-
Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials
such as scouring pads or powders, steel wool or abrasive paper
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>