BERTAZZONI REF36RCPIXL 36 Inch Built in Refrigerator Columns Instruction Manual

REF36RCPIXL 36 Inch Built in Refrigerator Columns

Specifications

• Product Type: Built-in Refrigerator Columns, Built-in Freezer
  Columns, Built-in Wine Columns, Built-in Bottom Mount

• Design Guide: North America

• Installation Options: Proud or Flush with cabinets

• Panel Options: Custom kitchen panels or stainless-steel
  doors

Product Usage Instructions

Refrigerators

Refrigerators are an essential part of your kitchen. Bertazzoni
offers a wide range of refrigerators with different sizes and
installation options to match your entire kitchen appliance suite.
There are three main styles available:

1. Columns: These refrigerators can be installed
   as 36″, 30″, or 24″ columns. They can accommodate custom kitchen
   panels or stainless-steel doors and handles.

2. Bottom Mount: These refrigerators are
   available in 36″ and 30″ sizes. They can be installed with a panel
   or ready for a custom panel.

3. French Door: French door models are also
   available in various sizes.

To install the built-in refrigerators, follow these steps:

Columns:

1. Choose the desired size: 36″, 30″, or 24″.

2. If using custom kitchen panels, make sure they are properly
   measured and prepared.

3. Install the refrigerator column by either installing a panel or
   using a panel-ready model.

4. If installing a panel, follow the specific instructions for the
   chosen size.

5. For panel-ready models, carefully align and attach the custom
   panel to the refrigerator.

6. Ensure the refrigerator is installed either proud or flush with
   the cabinets, based on your preference.

7. Install the handles according to the provided
   instructions.

Bottom Mount:

1. Choose the desired size: 36″ or 30″.

2. If using a custom panel, make sure it is properly measured and
   prepared.

3. Install the bottom mount refrigerator by either installing a
   panel or using a panel-ready model.

4. If installing a panel, follow the specific instructions for the
   chosen size.

5. For panel-ready models, carefully align and attach the custom
   panel to the refrigerator.

6. Ensure the refrigerator is installed either proud or flush with
   the cabinets, based on your preference.

7. Install the handles according to the provided
   instructions.

COLUMNS MULTIPLE INSTALLATIONS

If you want to install multiple refrigerator columns together,
Bertazzoni offers various configurations:

• Double Configurations: 42″, 48″, 54″, 60″
• Triple Configurations: 60″, 66″, 72″, 78″, 84″, 90″

For multiple installations of columns, follow these steps:

1. Select the desired configuration based on the available space
   and your needs.

2. Make sure to follow the individual installation instructions
   for each column size.

BUILT-IN WINE COLUMNS

Bertazzoni also offers built-in wine columns in 24″ and 18″
sizes. These columns can be installed with panels or as panel-ready
models. Follow these steps for installation:

1. Choose the desired size: 24″ or 18″.

2. If using custom kitchen panels, ensure they are properly
   measured and prepared.

3. Install the wine column by either installing a panel or using a
   panel-ready model.

4. If installing a panel, follow the specific instructions for the
   chosen size.

5. For panel-ready models, carefully align and attach the custom
   panel to the wine column.

6. Ensure the wine column is installed either proud or flush with
   the cabinets, based on your preference.

7. Install the handles according to the provided
   instructions.

FAQ

Q: Can I use custom kitchen panels with all the built-in

refrigerators?

A: Yes, all the built-in refrigerators are designed to
accommodate custom kitchen panels or stainless-steel doors and
handles that match your kitchen appliances.

Q: Can I install the refrigerators flush with the

cabinets?

A: Yes, the refrigerators can be installed either proud or flush
with the cabinets, allowing you to achieve your desired kitchen
style.

Q: Are installation instructions included with the

product?

A: Yes, each product comes with detailed installation
instructions specific to the size and type of refrigerator
column.

Q: Can I install multiple refrigerator columns together?

A: Yes, Bertazzoni offers various configurations for multiple
installations, including double and triple configurations.

Q: Are handles included with the refrigerators?

A: Yes, handles are included with the refrigerators. Follow the
provided instructions for handle installation.

BUILT-IN REFRIGERATOR COLUMNS BUILT-IN FREEZER COLUMNS BUILT-IN WINE COLUMNS BUILT-IN BOTTOM MOUNT DESIGN GUIDE – NORTH AMERICA
1.1

REFRIGERATORS
Refrigerators are a core building block of every kitchen. Bertazzoni offers a wide range of applications, sizes, and installation options, which are all harmonized by design to match the entire kitchen appliance suite.
Bertazzoni refrigerators are available in various styles, including Columns, Bottom Mount, and French Door models. With the Bertazzoni Design Guide, you can enjoy flawless installation of all the built-in 84″ models from the both the T and V tier lineup.
These built-in models are designed to accommodate custom kitchen panels or stainless-steel doors and handles that match the other appliances in your kitchen. They can be installed proud or flush with the cabinets, bringing your personal style to the kitchen.
We’ve taken care of every detail so that you can enjoy a seamless and elegant look in your kitchen.

INDEX

INTRODUCTION
T TIER LINE UP
BUILT-IN REFRIGERATOR COLUMNS 36″ Refrigerator Column Panel Installed 36″ Refrigerator Column Panel Ready 30″ Refrigerator Column Panel Installed 30″ Refrigerator Column Panel Ready 24″ Refrigerator Column Panel Installed 24″ Refrigerator Column Panel Ready
BUILT-IN FREEZER COLUMNS 30″ Freezer Column Panel Installed 30″ Freezer Column Panel Ready 24″ Freezer Column Panel Installed 24″ Freezer Column Panel Ready 18″ Freezer Column Panel Installed 18″ Freezer Column Panel Ready
BUILT-IN WINE COLUMNS 24″ Wine Column Panel Installed 24″ Wine Column Panel Ready 18″ Wine Column Panel Installed 18″ Wine Column Panel Ready
COLUMNS MULTIPLE INSTALLATIONS 42″ Double Configurations 48″ Double Configurations 54″ Double Configurations 60″ Double Configurations 60″ Triple Configurations 66″ Triple Configurations 72″ Triple Configurations 78″ Triple Configurations 84″ Triple Configurations 90″ Triple Configurations
Custom Door Panel Recommended Installations Refrigeration Handles Toekick Panel

2

BUILT-IN BOTTOM MOUNT REFRIGERATORS

76

36″ Bottom Mount Panel Installed

78

4

36″ Bottom Mount Panel Ready

81

30″ Bottom Mount Panel Installed

84

5

30″ Bottom Mount Panel Ready

87

7

10

BOTTOM MOUNT MULTIPLE INSTALLATIONS

90

13

60″ Bottom Mount Double Configurations

93

16

66″ Bottom Mount Configurations

94

19

72″ Bottom Mount Configurations

95

22

48″ Double Configurations

96

54″ Double Configurations

97

25

60″ Double Configurations

98

27

Bottom Mount Custom Door Panel

99

30

Bottom Mount Refrigeration Handles

100

33

36

V TIER LINE UP

101

39

42

BUILT-IN REFRIGERATOR COLUMNS

102

30″ Refrigerator Column Panel Ready

104

45

47

BUILT-IN FREEZER COLUMNS

107

50

18″ Freezer Column Panel Ready

109

53

56

COLUMNS MULTIPLE INSTALLATIONS

112

48″ Double Configurations

115

59

62

Custom Door Panel

116

63

Recommended Installations

117

64

Refrigeration Handles

118

65

66

BUILT-IN BOTTOM MOUNT REFRIGERATORS 119

67

36″ Bottom Mount Panel Ready

121

68

30″ Bottom Mount Panel Ready

124

69

70

BOTTOM MOUNT MULTIPLE INSTALLATIONS 127

71

60″ Bottom Mount Double Configurations

130

72 73

66″ Bottom Mount Double Configurations 72″ Bottom Mount Double Configurations

131 132

74

Bottom Mount Custom Door Panel

133

75

Bottom Mount Refrigeration Handles

134

bertazzoni.com

3

T TIER LINE UP

4

bertazzoni.com

BUILT-IN REFRIGERATOR COLUMNS

BUILT-IN COLUMNS
Refrigerators, freezers, and wine columns from the T tier are masterpieces of design and technology. Their stylish appearance reflects close attention to detail and high-quality materials, inside and out. The stainless steel front and panel-ready doors are mounted with state-of-the-art engineered lift- andswing hinges that give the perception of a weightless range of motion. Versatile installation options make it possible to bring together elegant configurations of the refrigerator, freezer, and wine column in any desired width. All three columns work in harmony with handles and finishes available for every Series.

36″ – 30″ – 24″ Panel Ready and Panel Installed

bertazzoni.com

5

6

bertazzoni.com

BUILT-IN REFRIGERATOR COLUMNS
36″ Refrigerator Column Panel Installed Dimensions
REF36RCPIXL/23 left hinge REF36RCPIXR/23 right hinge
Handle choices Professional Series: PROHKCOL Master series: MASHKCOL Heritage Series: HERHKCOL

SIDE VIEW

22 1/16″ 560

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

FRONT VIEW
35 5/8″ 904
DOOR WIDTH
83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW
35 5/8″ 904
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

TOP VIEW

5 1/2″ 139

58 3/8″ 1482

35 15/16″ 913
24 3/16″ 615
100°

TOP VIEW

24 3/16″ 615

35 15/16″ 913

100°

5 1/2″ 139

58 3/8″ 1482

• Maximum Overall Handle Dimension For detailed handle dimensions see page 74

bertazzoni.com

7

BUILT-IN REFRIGERATOR COLUMNS
36″ Refrigerator Column Panel Installed Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product.
For instructions of product combinations please see the Multiple Installation Section (page 59).
CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1532 lb (695 kg )

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 218 W 2 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

8

bertazzoni.com

BUILT-IN REFRIGERATOR COLUMNS
36″ Refrigerator Column Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635

FRONT VIEW

a

a

36″ 914 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

bertazzoni.com

9

BUILT-IN REFRIGERATOR COLUMNS
36″ Refrigerator Column Panel Ready Dimensions
REF36RCPRL/23 left hinge REF36RCPRR/23 right hinge

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

TOP VIEW

6 1/4″ 158

**

58 7/16″ 1484

35 15/16″ 913
24″ 610
100°

TOP VIEW
35 15/16″ 913
24″ 610
100°

6 1/4″ 158

581478/146″ **

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 72 For detailed handle dimensions see page 74
  10 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN REFRIGERATOR COLUMNS
36″ Refrigerator Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1532 lb (695 kg )

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 218 W 2 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 11

BUILT-IN REFRIGERATOR COLUMNS
36″ Refrigerator Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

36″ 914
83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual
12 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Installed Dimensions
REF30RCPIXL/23 left hinge REF30RCPIXR/23 right hinge
Handle choices Professional Series: PROHKCOL Master series: MASHKCOL Heritage Series: HERHKCOL

SIDE VIEW

22 1/16″ 560

FRONT VIEW
29 5/8″ 752
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW
29 5/8″ 752
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

TOP VIEW

4″ 103

52 3/8″ 1331

29 15/16″ 761
24 3/16″ 615
100°

TOP VIEW

29 15/16″ 761
24 3/16″ 615
100°

4″ 103

52 3/8″ 1331

• Maximum Overall Handle Dimension For detailed handle dimensions see page 74

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 13

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Installed Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product.
For instructions of product combinations please see the Multiple Installation Section (page 59).
CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Required floor support

1257 lb (570 kg )

Electrical supply 115 V 60 Hz 218 W 2 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

14 bertazzoni.com

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635

FRONT VIEW

a

a

30″ 762 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.
bertazzoni.com 15

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Ready Dimensions
REF30RCPRL/23 left hinge REF30RCPRR/23 right hinge

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

TOP VIEW

5 1/4″ 132

**

52 1/2″ 1333

29 15/16″ 761
24″ 610
100°

TOP VIEW

29 15/16″ 761
24″ 610
100°

5 1/4″ 132

52 1/2″ 1333

**

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 72 For detailed handle dimensions see page 74
  16 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1257 lb (570 kg )

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 218 W 2 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 17

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

30″ 762
83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual
18 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN REFRIGERATOR COLUMNS
24″ Refrigerator Column Panel Installed Dimensions
REF24RCPIXL/23 left hinge REF24RCPIXR/23 right hinge
Handle choices Professional Series: PROHKCOL Master series: MASHKCOL Heritage Series: HERHKCOL

SIDE VIEW

22 1/16″ 560

FRONT VIEW
23 5/8″ 600
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW
23 5/8″ 600
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

TOP VIEW

3 1/2″ 89

46 1/2″ 1181

24″ 609
24 3/16″ 615
100°

TOP VIEW

24 3/16″ 615

24″ 609
100°

3

1/2″ 89

46 1/2″ 1181

• Maximum Overall Handle Dimension For detailed handle dimensions see page 74

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 19

BUILT-IN REFRIGERATOR COLUMNS
24″ Refrigerator Column Panel Installed Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product.
For instructions of product combinations please see the Multiple Installation Section (page 59).
CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Required floor support

992 lb (450 kg )

Electrical supply 115 V 60 Hz 163 W 1.5 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

20 bertazzoni.com

BUILT-IN REFRIGERATOR COLUMNS
24″ Refrigerator Column Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635

FRONT VIEW

a

a

24″ 610 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.
bertazzoni.com 21

BUILT-IN REFRIGERATOR COLUMNS
24″ Refrigerator Column Panel Ready Dimensions
REF24RCPRL/23 left hinge REF24RCPRR/23 right hinge

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

TOP VIEW

4 1/4″ 108

**

46 9/16″ 1183

24″ 609
24″ 610
100°

TOP VIEW

24″ 609
24″ 610
100°

4 1/4″ 108

46 9/16″ 1183

**

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 72 For detailed handle dimensions see page 74
  22 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN REFRIGERATOR COLUMNS
24″ Refrigerator Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

992 lb (450 kg )

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 163 W 1.5 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 23

BUILT-IN REFRIGERATOR COLUMNS
24″ Refrigerator Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

24″ 610
83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual
24 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN FREEZER COLUMNS

30″ – 24″ – 18″ Panel Ready and Panel Installed

bertazzoni.com 25

26 bertazzoni.com

BUILT-IN FREEZER COLUMNS
30″ Freezer Column Panel Installed Dimensions
REF30FCPIXL/23 left hinge REF30FCPIXR/23 right hinge
Handle choices Professional Series: PROHKCOL Master series: MASHKCOL Heritage Series: HERHKCOL

SIDE VIEW

22 1/16″ 560

FRONT VIEW
29 5/8″ 752
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW
29 5/8″ 752
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

TOP VIEW

4″ 103

52 3/8″ 1331

29 15/16″ 761
24 3/16″ 615
100°

TOP VIEW

29 15/16″ 761
24 3/16″ 615
100°

4″ 103

52 3/8″ 1331

• Maximum Overall Handle Dimension For detailed handle dimensions see page 74

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 27

BUILT-IN FREEZER COLUMNS
30″ Freezer Column Panel Installed Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product.
For instructions of product combinations please see the Multiple Installation Section (page 59).
CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1257 lb (570 kg )

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW
A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 327 W 3 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

PLUMBING REQUIREMENTS
Bertazzoni Freezer Columns are provided with a water filter assembly which must be mounted outside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see Use and Maintenance Manual.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

28 bertazzoni.com

BUILT-IN FREEZER COLUMNS
30″ Freezer Column Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635

FRONT VIEW

a

a

30″ 762 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.
bertazzoni.com 29

BUILT-IN FREEZER COLUMNS
30″ Freezer Column Panel Ready Dimensions
REF30FCPRL/23 left hinge REF30FCPRR/23 right hinge

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

TOP VIEW

5 1/4″ 132

**

52 1/2″ 1333

29 15/16″ 761
24″ 610
100°

TOP VIEW

29 15/16″ 761
24″ 610
100°

5 1/4″ 132

52 1/2″ 1333

**

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 72 For detailed handle dimensions see page 74
  30 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN FREEZER COLUMNS
30″ Freezer Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1257 lb (570 kg )

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.
For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 327 W 3 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

PLUMBING REQUIREMENTS
Bertazzoni Freezer Columns are provided with a water filter assembly which must be mounted outside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see Use and Maintenance Manual.
Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 31

BUILT-IN FREEZER COLUMNS
30″ Freezer Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

30″ 762
83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual
32 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN FREEZER COLUMNS
24″ Freezer Column Panel Installed Dimensions
REF24FCIPIXL/23 left hinge REF24FCIPIXR/23 right hinge
Handle choices Professional Series: PROHKCOL Master series: MASHKCOL Heritage Series: HERHKCOL

SIDE VIEW

22 1/16″ 560

FRONT VIEW
23 5/8″ 600
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW
23 5/8″ 600
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

TOP VIEW

3 1/2″ 89

46 1/2″ 1181

24″ 609
24 3/16″ 615
100°

TOP VIEW

24 3/16″ 615

24″ 609
100°

3

1/2″ 89

46 1/2″ 1181

• Maximum Overall Handle Dimension For detailed handle dimensions see page 74

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 33

BUILT-IN FREEZER COLUMNS
24″ Freezer Column Panel Installed Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product..
For instructions of product combinations please see the Multiple Installation Section (page 59).
CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

992 lb (450 kg )

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 327 W 3 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

PLUMBING REQUIREMENTS
Bertazzoni Freezer Columns are provided with a water filter assembly which must be mounted outside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see Use and Maintenance Manual.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

34 bertazzoni.com

BUILT-IN FREEZER COLUMNS
24″ Freezer Column Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635

FRONT VIEW

a

a

24″ 610 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.
bertazzoni.com 35

BUILT-IN FREEZER COLUMNS
24″ Freezer Column Panel Ready Dimensions
REF24FCIPRL/23 left hinge REF24FCIPRR/23 right hinge

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

TOP VIEW

4 1/4″ 108

**

46 9/16″ 1183

24″ 609
24″ 610
100°

TOP VIEW

24″ 609
24″ 610
100°

4 1/4″ 108

46 9/16″ 1183

**

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 72 For detailed handle dimensions see page 74
  36 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN FREEZER COLUMNS
24″ Freezer Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

992 lb (450 kg )

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.
For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 327 W 3 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

PLUMBING REQUIREMENTS
Bertazzoni Freezer Columns are provided with a water filter assembly which must be mounted outside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see Use and Maintenance Manual.
Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 37

BUILT-IN FREEZER COLUMNS
24″ Freezer Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

24″ 610
83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual
38 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN FREEZER COLUMNS
18″ Freezer Column Panel Installed Dimensions
REF18FCIPIXL/23 left hinge REF18FCIPIXR/23 right hinge
Handle choices Professional Series: PROHKCOL Master series: MASHKCOL Heritage Series: HERHKCOL

SIDE VIEW

22 1/16″ 560

FRONT VIEW
17 5/8″ 447
DOOR WIDTH

5″ 127
2 3/4″ 70

80 3/4″ 2050
+ 1″(25)
19 5/8″ 500

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

5 3/4″ 146

1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW
17 5/8″ 447
DOOR WIDTH

5″ 127
2 3/4″ 70

80 3/4″ 2050
+ 1″(25)
19 5/8″ 500

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

5 3/4″ 146

1″(25)

TOP VIEW

2 1/2″ 63

17 15/16″ 456

40 1/2″ 1029

24 3/16″ 615
100°

TOP VIEW

17 15/16″ 456

2 1/2″ 63

24 3/16″ 615
100°

40 1/2″ 1029

• Maximum Overall Handle Dimension For detailed handle dimensions see page 74

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 39

BUILT-IN FREEZER COLUMNS
18″ Freezer Column Panel Installed Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product.
For instructions of product combinations please see the Multiple Installation Section (page 59).
CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

694 lb (315 kg )

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 327 W 3 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

PLUMBING REQUIREMENTS
Bertazzoni Freezer Columns are provided with a water filter assembly which must be mounted outside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see Use and Maintenance Manual.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

40 bertazzoni.com

BUILT-IN FREEZER COLUMNS
18″ Freezer Column Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635
FRONT VIEW
aa
18″ 457 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.
bertazzoni.com 41

BUILT-IN FREEZER COLUMNS
18″ Freezer Column Panel Ready Dimensions
REF18FCIPRL/23 left hinge REF18FCIPRR/23 right hinge

SIDE VIEW

22 1/16″ 560

FRONT VIEW

5″ 127
2 3/4″ 70

80 3/4″ 2050
+ 1″(25)

71 1/8″ 1808

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

5″ 127
2 3/4″ 70

80 3/4″ 2050
+ 1″(25)

71 1/8″ 1808

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

TOP VIEW

3 1/4″ 82

17 15/16″ 456

**

40 9/16″ 1031

24″ 610
100°

TOP VIEW

17 15/16″ 456

3 1/4″ 82

24″ 610
100°

40 9/16″ 1031

**

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 72 For detailed handle dimensions see page 74
  42 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN FREEZER COLUMNS
18″ Freezer Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

694 lb (315 kg )

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.
For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 327 W 3 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

PLUMBING REQUIREMENTS
Bertazzoni Freezer Columns are provided with a water filter assembly which must be mounted outside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see Use and Maintenance Manual.
Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 43

18″ BUILT-IN FREEZER COLUMNS
18″ Freezer Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635
FRONT VIEW
aa
18″ 457 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual
44 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN WINE COLUMNS

24″ – 18″ Panel Ready and Panel Installed

bertazzoni.com 45

46 bertazzoni.com

BUILT-IN WINE COLUMNS
24″ Wine Column Panel Installed Dimensions
REF24WCPIXL/23 left hinge REF24WCPIXR/23 right hinge
Handle choices Professional Series: PROHKCOL Master series: MASHKCOL Heritage Series: HERHKCOL

SIDE VIEW

22 1/16″ 560

FRONT VIEW
23 5/8″ 600
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW
23 5/8″ 600
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

TOP VIEW

3 1/2″ 89

46 1/2″ 1181

24″ 609
24 3/16″ 615
100°

TOP VIEW

24 3/16″ 615

24″ 609
100°

3

1/2″ 89

46 1/2″ 1181

• Maximum Overall Handle Dimension For detailed handle dimensions see page 74

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 47

BUILT-IN WINE COLUMNS
24″ Wine Column Panel Installed Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product.
For instructions of product combinations please see the Multiple Installation Section (page 59).
CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Required floor support

992 lb (450 kg )

Electrical supply 115 V 60 Hz 152 W 1.4 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

48 bertazzoni.com

BUILT-IN WINE COLUMNS
24″ Wine Column Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635

FRONT VIEW

a

a

24″ 610 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.
bertazzoni.com 49

BUILT-IN WINE COLUMNS
24″ Wine Column Panel Ready Dimensions
REF24WCPRL/23 left hinge REF24WCPRR/23 right hinge

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

71 1/8″ 1808

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

TOP VIEW

4 1/4″ 108

**

46 9/16″ 1183

24″ 609
24″ 610
100°

TOP VIEW

24″ 609
24″ 610
100°

4 1/4″ 108

46 9/16″ 1183

**

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 72 For detailed handle dimensions see page 74
  50 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. For custom panel dimensions and window cutout see page 69.

BUILT-IN WINE COLUMNS
24″ Wine Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

992 lb (450 kg )

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 152 W 1.4 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 51

BUILT-IN WINE COLUMNS
24″ Wine Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

24″ 610
83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual
52 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN WINE COLUMNS
18″ Wine Column Panel Installed Dimensions
REF18WCPIXL/23 left hinge REF18WCPIXR/23 right hinge
Handle choices Professional Series: PROHKCOL Master series: MASHKCOL Heritage Series: HERHKCOL

SIDE VIEW

22 1/16″ 560

FRONT VIEW

5″ 127
2 3/4″ 70

80 3/4″ 2050
+ 1″(25)
19 5/8″ 500

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

5 3/4″ 146

1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

5″ 127
2 3/4″ 70

80 3/4″ 2050
+ 1″(25)
19 5/8″ 500

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

5 3/4″ 146

1″(25)

• Maximum Overall Handle Dimension For detailed handle dimensions see page 74

TOP VIEW

17 5/8″ 447
DOOR WIDTH

2 1/2″ 63

17 15/16″ 456

40 1/2″ 1029

24 3/16″ 615
100°

17 5/8″ 447
DOOR WIDTH

TOP VIEW

17 15/16″ 456

2 1/2″ 63

24 3/16″ 615
100°

40 1/2″ 1029

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 53

BUILT-IN WINE COLUMNS
18″ Wine Column Panel Installed Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product.
For instructions of product combinations please see the Multiple Installation Section (page 59).
CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Required floor support

694 lb (315 kg )

Electrical supply 115 V 60 Hz 152 W 1.4 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

54 bertazzoni.com

BUILT-IN WINE COLUMNS
18″ Wine Column Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635
FRONT VIEW
aa
18″ 457 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.
bertazzoni.com 55

BUILT-IN WINE COLUMNS
18″ Wine Column Panel Ready Dimensions
REF18WCPRL/23 left hinge REF18WCPRR/23 right hinge

SIDE VIEW

22 1/16″ 560

FRONT VIEW

5″ 127
2 3/4″ 70

80 3/4″ 2050
+ 1″(25)

71 1/8″ 1808

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

SIDE VIEW

22 1/16″ 560

FRONT VIEW

5″ 127
2 3/4″ 70

80 3/4″ 2050
+ 1″(25)

71 1/8″ 1808

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

TOP VIEW

3 1/4″ 82

17 15/16″ 456

24 ” 610

**

40 9/16″ 1031

100°

TOP VIEW

17 15/16″ 456

3 1/4″ 82

24 ” 610

40 9/16″ 1031

**

100°

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 72 For detailed handle dimensions see page 74
  56 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. For custom panel dimensions and window cutout see page 69.

BUILT-IN WINE COLUMNS
18″ Wine Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

E

E

E

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

694 lb (315 kg )

FRONT VIEW

5″

127

E

E

E

MAX

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 152 W 1.4 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 79″ power cord

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 57

BUILT-IN WINE COLUMNS
18″ Wine Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635
FRONT VIEW
aa
18″ 457 83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140x100mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual
58 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

COLUMNS MULTIPLE INSTALLATIONS
bertazzoni.com 59

60 bertazzoni.com

MULTIPLE INSTALLATIONS
Multiple installations Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliances and the adjacent cabinets, special side profiles are factory-installed and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 75 pounds (34 kg) for door panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).
For instructions of product combinations please see the Multiple Installation Section (page 59).

TOP VIEW

E

E

E

FRONT VIEW

5″

127

E

E

E

MAX

A separate 10 Amp circuit breaker servicing only these appliances is recommended.

CABINET REQUIREMENT
Installation of the appliances must be performed in accordance with the provisions of applicable legislation. Be sure that support of these appliances is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of all the appliances when in use. Please see any single product installation manual for required floor support.
ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

PLUMBING REQUIREMENTS
Bertazzoni Freezer Columns are provided with a water filter assembly which must be mounted outside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see Use and Maintenance Manual.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 61

MULTIPLE INSTALLATIONS – 42″ DOUBLE CONFIGURATIONS
42″ Double Configurations Flush installation

POSSIBLE COMBINATIONS c
REF24RCPIX(L/R)/23 REF18FCIPIX(L/R)/23 REF24RCPR(L/R)/23 REF18FCIPR(L/R)/23
REF24RCPIX(L/R)/23 REF18WCPIX(L/R)/23 REF24RCPR(L/R)/23 REF18FCIPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

42″ 1067

(a) Area to be left clear for the anti-tipping brackets ­ 42″x4″ (1067x100mm)
All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.
62 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel. c: Optional 42 inch bridge toe kick accessory is available.
For details see page 75

MULTIPLE INSTALLATIONS – 48″ DOUBLE CONFIGURATIONS
48″ Double Configurations Flush installation

POSSIBLE COMBINATIONS c
REF30RCPIX(L/R)/23 REF18FCIPIX(L/R)/23 REF30RCPR(L/R)/23 REF18FCIPR(L/R)/23
REF30RCPIX(L/R)/23 REF18WCPIX(L/R)/23 REF30RCPR(L/R)/23 REF18WCPR(L/R)/23
REF24RCPIX(L/R)/23 REF24FCIPIX(L/R)/23 REF24RCPR(L/R)/23 REF24FCIPR(L/R)/23
REF24RCPIX(L/R)/23 REF24WCPIX(L/R)/23 REF24RCPR(L/R)/23 REF24WCPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

48″ 1219

a: Area to be left clear for the anti-tipping brackets ­ 48″x4″ (1219x100mm)
b: Depth includes kitchen cabinet front panel. c: Optional 48 inch bridge toe kick accessory is available.
For details see page 75

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.
bertazzoni.com 63

MULTIPLE INSTALLATIONS – 54″ DOUBLE CONFIGURATIONS
54″ Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF30RCPIX(L/R)/23 REF24FCIPIX(L/R)/23 REF30RCPR(L/R)/23 REF24FCIPR(L/R)/23
REF30RCPIX(L/R)/23 REF18WCPIX(L/R)/23 REF30RCPR(L/R)/23 REF18WCPR(L/R) /23
REF36RCPIX(L/R)/23 REF18FCIPIX(L/R)/23 REF36RCPR(L/R)/23 REF18FCIPR(L/R)/23
REF36RCPIX(L/R)/23 REF18WCPIX(L/R)/23 REF36RCPR(L/R)/23 REF18WCPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

54″ 1372

a: Area to be left clear for the anti-tipping brackets ­ 54″x4″ (1372x100mm)
b: Depth includes kitchen cabinet front panel.
64 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.

MULTIPLE INSTALLATIONS – 60″ DOUBLE CONFIGURATIONS
60″ Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF30RCPIX(L/R)/23 REF30FCIPIX(L/R)/23 REF30RCPR(L/R)/23 REF30FCIPR(L/R)/23
REF36RCPIX(L/R)/23 REF24WCPIX(L/R)/23 REF36RCPR(L/R)/23 REF24WCPR(L/R)/23
REF36RCPIX(L/R)/23 REF24FCIPIX(L/R)/23 REF36RCPR(L/R)/23 REF24FCIPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

60″ 1524

a: Area to be left clear for the anti-tipping brackets ­ 60″x4″ (1524x100mm)
b: Depth includes kitchen cabinet front panel.

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.
bertazzoni.com 65

MULTIPLE INSTALLATIONS – 60″ TRIPLE CONFIGURATIONS
60″ Triple Configurations Flush installation

POSSIBLE COMBINATIONS
REF24RCPIX(L/R)/23 REF18FCIPIX(L/R)/23 REF18WCPIX(L/R)/23
REF24RCPR(L/R)/23 REF18FCIPR(L/R)/23 REF18WCPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

60″ 1524

a: Area to be left clear for the anti-tipping brackets ­ 60″x4″ (1524x100mm)
b: Depth includes kitchen cabinet front panel.
66 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.

MULTIPLE INSTALLATIONS – 66″ TRIPLE CONFIGURATIONS
66″ Triple Configurations Flush installation

POSSIBLE COMBINATIONS
REF30RCPIX(L/R)/23 REF18FCIPIX(L/R)/23 REF18WCPIX(L/R)/23
REF30RCPR(L/R)/23 REF18FCIPR(L/R)/23 REF18WCPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

66″ 1676

a: Area to be left clear for the anti-tipping brackets ­ 66″x4″ (1676x100mm)
b: Depth includes kitchen cabinet front panel.

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.
bertazzoni.com 67

MULTIPLE INSTALLATIONS – 72″ TRIPLE CONFIGURATIONS
72″ Triple Configurations Flush installation

POSSIBLE COMBINATIONS
REF24RCPIX(L/R)/23 REF24FCIPIX(L/R)/23 REF24WCPIX(L/R)/23
REF24RCPR(L/R)/23 REF24FCIPR(L/R)/23 REF24WCPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

72″ 1829

a: Area to be left clear for the anti-tipping brackets ­ 72″x4″ (1829x100mm)
b: Depth includes kitchen cabinet front panel.
68 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.

MULTIPLE INSTALLATIONS – 78″ TRIPLE CONFIGURATIONS
78″ Triple Configurations Flush installation

POSSIBLE COMBINATIONS
REF30RCPIX(L/R)/23 REF24FCIPIX(L/R)/23 REF24WCPIX(L/R)/23
REF30RCPR(L/R)/23 REF24FCIPR(L/R)/23 REF24WCPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

78″ 1981

a: Area to be left clear for the anti-tipping brackets ­ 78″x4″ (1981x100mm)
b: Depth includes kitchen cabinet front panel.

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.
bertazzoni.com 69

MULTIPLE INSTALLATIONS – 84″ TRIPLE CONFIGURATIONS
84″ Triple Configurations Flush installation

POSSIBLE COMBINATIONS
REF36RCPIX(L/R)/23 REF30FCIPIX(L/R)/23 REF18WCPIX(L/R)/23
REF36RCPR(L/R)/23 REF30FCIPR(L/R)/23 REF18WCPR(L/R)/23
REF30RCPIX(L/R)/23 REF30FCIPIX(L/R)/23 REF24WCPIX(L/R)/23
REF30RCPR(L/R)/23 REF30FCIPR(L/R)/23 REF24WCPR(L/R)/23
REF36RCPIX(L/R)/23 REF24FCIPIX(L/R)/23 REF24WCPIX(L/R)/23
REF36RCPR(L/R)/23 REF24FCIPR(L/R)/23 REF24WCPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

84″ 2134

a: Area to be left clear for the anti-tipping brackets ­ 84″x4″ (2134x100mm)
b: Depth includes kitchen cabinet front panel.
70 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.

MULTIPLE INSTALLATIONS – 90″ TRIPLE CONFIGURATIONS
90″ Triple Configurations Flush installation

POSSIBLE COMBINATIONS c
REF36RCPIX(L/R)/23 REF30FCIPIX(L/R)/23 REF24WCPIX(L/R)/23
REF36RCPR(L/R)/23 REF30FCIPR(L/R)/23 REF24WCPR(L/R)/23

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

90″ 2286

a: Area to be left clear for the anti-tipping brackets ­ 90″x4″ (2286x100mm)
b: Depth includes kitchen cabinet front panel. c: Optional 42 inch bridge toe kick accessory is available.
For details see page 75

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.
bertazzoni.com 71

MULTIPLE INSTALLATIONS – CUSTOM DOOR PANEL
Custom Door Panel

CUSTOM HANDLE MOUNTING AREA ON LEFT SWING DOOR

REAR PANEL DRILLING

WINE COLUMN DOOR WINDOW DIMENSIONS

CUSTOM HANDLES MOUNTING AREA

max 11 13/16″ max 300

A

B

B

5 1/2″

C

139

5 1/2″ 139

D

D

6 1/2″ 165
27 1/8″ 690

1/2″

4 3/8″

13

112

7 7/8″ 200

83 1/2″ 2120

50″ 1272
70 3/4″ 1797

79 13/16″ 2027

61 7/8″ 1572

CUSTOM HANDLE MOUNTING AREA ON RIGHT SWING DOOR

standard 4″ 100

1 3/8″ 34
min 3 1/8″ 80

1 3/8″ 34

10 1/16″ 255

36″

30″

24″

18″

A 35 3/4″ (908) 29 3/4″ (756) 23 3/4″ (604) 17 3/4″ (451)

B 16 1/2″ (418) 13 1/2″ (343) 10 7/8″ (275) 7 7/8″ (200)

C

­

­

12 7/8″ (327) 6 7/8″ (177)

D 7 1/8″ (182)

6″ (152)

4 3/4″ (121) 3 5/8″ (92)

72 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

MULTIPLE INSTALLATIONS – RECOMMENDED INSTALLATIONS
Recommended Installations
RECOMMENDED INSTALLATIONS
NOT RECOMMENDED INSTALLATIONS
bertazzoni.com 73

MULTIPLE INSTALLATIONS – REFRIGERATION HANDLES
Refrigeration Handles

PROFESSIONAL SERIES PROHKCOL
1 1/2″ 37
2 1/8″ 53

MASTER SERIES MASHKCOL
1 3/4″ 45
2 3/8″ 59

HERITAGE SERIES HERHKCOL
1 1/4″ 31
2 3/8″ 59

BERTAZZONI HANDLES DRILLING ON RIGHT SWING DOOR
1 5/8″ 42
35 3/8″ 900

BERTAZZONI HANDLES DRILLING ON LEFT SWING DOOR
1 5/8″ 42
35 3/8″ 900

20 1/4″ 514

20 1/4″ 514

HANDLE INSTALLATION ON CUSTOM PANELS
In case a custom panel is to be mounted on any of the models listed below with Bertazzoni handles,it will be necessary to install M5 x 0.8 mm brass tapping inserts in order to secure the handle properly on the custom panel. Recommended drill bit size to drill the pilot hole is 3/8″. Suitable inserts can be ordered at www.encompass.com

Part Number: 95631A100, contains n°4 M5 brass hardwood inserts and 1 M5 installation bit. Do not use a power tool to mount the inserts. Installation of the inserts with improperly calibrated power tools risk damaging the panels.

74 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

MULTIPLE INSTALLATIONS – TOEKICK PANEL
Toekick Panel

Part number 901560

Part number 901561

Installation of multiple column units with a continuous cabinet toe kick are possible. Details are provided in the Bertazzoni Columns installation manual.

bertazzoni.com 75

BUILT-IN BOTTOM MOUNT REFRIGERATORS

These refrigerators from the T tier are masterpieces of design, styled to reflect Bertazzoni’s meticulous attention to detail. They are practical, too – incorporating the latest technology to retain the nutritional value, vitamins, minerals, and texture of your food for longer. Designed for true flush installation in a standard depth cabinet, they are available in both stainless steel and panel-ready models for a seamless installation with any adjacent cabinetry and can be installed side-byside, doubling your refrigerator space. Add the finishing touch with Professional, Master, or Heritage Series handles to match the other appliances in your kitchen. The side-by-side installation kit lets you create clean lines in your kitchen. “Lift and swing” hinges are available on 36″ and 30″ models to allow a minimal vertical gap of 1/8″ between adjacent front cabinet panels.

36″ Panel Installed and Panel Ready

30″ Panel Installed and Panel Ready

76 bertazzoni.com

bertazzoni.com 77

BUILT-IN BOTTOM MOUNT REFRIGERATORS
36″ Bottom Mount Panel Installed Dimensions
REF36BMBIXLT left hinge REF36BMBIXRT right hinge
Handle choices Professional Series: PROHK36PI Master series: MASHK36PI Heritage Series: HERHK36PI

SIDE VIEW

41 7/8″ 1065 22″ 560

FRONT VIEW
35 5/8″ 904
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

TOP VIEW

9″ 230

54 1/4″ 1378
58 3/8″ 3/8″ 1482
9
23 1/8″ 587

35 15/16″ 913
105°

SIDE VIEW

41 7/8″ 1065 22″ 560

FRONT VIEW
35 5/8″ 904
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

54 1/4″ 1378
3/8″ 9
23 1/8″ 587

TOP VIEW
35 15/16″ 913
25″ 635
105°

25″ 635

9″ 230

58 3/8″ 1482

• Maximum Overall Handle Dimension For detailed handle dimensions see page 100
  78 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN BOTTOM MOUNT
36″ Bottom Mount Panel Installed Installation requirements

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 550 W 4.8 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 98″ power cord

Required floor support

1532 lb (695 kg )

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

EW

EW

EW

PLUMBING REQUIREMENT
Bertazzoni Bottom Mount refrigerators are provided with a water filter assembly which must be mounted inside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system.

FRONT VIEW
5″ 127
EW E W EW

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 79

BUILT-IN BOTTOM MOUNT
36″ Bottom Mount Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635

FRONT VIEW

a

a

36″ 914
83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140×100 mm)
80 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN BOTTOM MOUNT
36″ Bottom Mount Panel Ready Dimensions
REF36BMBIPLT left hinge REF36BMBIPRT right hinge
Handle choices Professional Series: PROHK36PI Master series: MASHK36PI Heritage Series: HERHK36PI

SIDE VIEW

42″ 1068

22″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

2 3/4″ 70
SIDE VIEW

19 5/8″ 500

42″ 1068

22″ 560

83 1/2″ 2120
+ 1″(25)
FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 99 For detailed handle dimensions see page 100

TOP VIEW

8 1/8″ 206

51 1/8″ 1299

**

58 1/8″ 1475

3/4″

20

18 5/8″ 474

35 15/16″ 913
24″ 610
105°

9 3/4″ 248

+1″(25)

TOP VIEW

51 1/8″ 1299

24″ 610

3/4″ 20
18 5/8″ 474

35 15/16″ 913
105°

9 3/4″ 248

+1″(25)

8 1/8″ 206

58 1/8″ 1475

**

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 81

BUILT-IN BOTTOM MOUNT
36″ Bottom Mount Panel Ready Installation requirements

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1532 lb (695 kg)

For panel ready bottom mount, do not exceed the maximum weight of 51 pounds (23 kg) for door panel and 25 pounds (11 kg) for drawer panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW
A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 550 W 4.8 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 98″ power cord

PLUMBING REQUIREMENT
Bertazzoni Bottom Mount refrigerators are provided with a water filter assembly which must be mounted inside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

82 bertazzoni.com

BUILT-IN BOTTOM MOUNT
36″ Bottom Mount Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

83 7/8″ 2130 Min.

36″ 914*

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140×100 mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel. * 36 1/8″ (917) for framed-in installation.
bertazzoni.com 83

BUILT-IN BOTTOM MOUNT
30″ Bottom Mount Panel Installed Dimensions
REF30BMBIXLT left hinge REF30BMBIXRT right hinge
Handle choices Professional Series: PROHK30PI Master series: MASHK30PI Heritage Series: HERHK30PI

SIDE VIEW

41 7/8″ 1065

22″

560

FRONT VIEW
29 5/8″ 752
DOOR WIDTH

TOP VIEW

7 5/8″ 195

29 15/16″ 761

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

54 1/4″ 1378
3/8″ 9

52 3/8″ 1332

23 1/8″ 587

25″ 635
105°

SIDE VIEW

41 7/8″ 1065

22″

560

FRONT VIEW
29 5/8″ 752
DOOR WIDTH

80 3/4″ 2050
+ 1″(25) 5″ 127

77 3/4″ 1974

83 1/2″ 2120
+ 1″(25)

2 3/4″ 70

19 5/8″ 500

5 3/4″ 146

1″(25)

54 1/4″ 1378
3/8″ 9
23 1/8″ 587

TOP VIEW
29 15/16″ 761
25″ 635
105°

7 5/8″ 195

52 3/8″ 1332

• Maximum Overall Handle Dimension For detailed handle dimensions see page 100
  84 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN BOTTOM MOUNT
30″ Bottom Mount Panel Installed Installation requirements

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 470 W 4.1 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 98″ power cord

Required floor support

1257 lb (570 kg)

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

EW

EW

EW

PLUMBING REQUIREMENT
Bertazzoni Bottom Mount refrigerators are provided with a water filter assembly which must be mounted inside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system.

FRONT VIEW
5″ 127
EW E W EW

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 85

BUILT-IN BOTTOM MOUNT
30″ Bottom Mount Panel Installed Flush installation

SIDE VIEW

TOP VIEW b
25″ 635

FRONT VIEW

a

a

30″ 762
83 7/8″ 2130 Min.

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140×100 mm)
86 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

BUILT-IN BOTTOM MOUNT
30″ Bottom Mount Panel Ready Dimensions
REF30BMBIPLT left hinge REF30BMBIPRT right hinge
Handle choices Professional Series: PROHK30PI Master series: MASHK30PI Heritage Series: HERHK30PI

SIDE VIEW

42″ 1068

22″ 560

FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

2 3/4″ 70
SIDE VIEW

19 5/8″ 500

42″ 1068

22″ 560

83 1/2″ 2120
+ 1″(25)
FRONT VIEW

80 3/4″ 2050
+ 1″(25) 5″ 127

2 3/4″ 70

19 5/8″ 500

83 1/2″ 2120
+ 1″(25)

• Maximum Overall Handle Dimension ** 3/4″ (19mm) Door Panel thickness For custom panel dimensions see page 99 For detailed handle dimensions see page 100

TOP VIEW

6 3/4″ 171

51 1/8″ 1299

52 1/8″ 1325

**

3/4″ 20

18 5/8″ 474

29 15/16″ 761
24″ 610
105°

9 3/4″ 248

+1″(25)

TOP VIEW

51 1/8″ 1299

29 15/16″ 761
24″ 610

3/4″ 20
18 5/8″ 474

105°

6 3/4″ 171

52 1/8″ 1325

**

9 3/4″ 248

+1″(25)

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 87

BUILT-IN BOTTOM MOUNT
30″ Bottom Mount Panel Ready Installation requirements

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1257 lb (570 kg)

For panel ready bottom mount, do not exceed the maximum weight of 51 pounds (23 kg) for door panel and 25 pounds (11 kg) for drawer panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW
A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 470 W 4.1 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 98″ power cord

PLUMBING REQUIREMENT
Bertazzoni Bottom Mount refrigerators are provided with a water filter assembly which must be mounted inside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

88 bertazzoni.com

BUILT-IN BOTTOM MOUNT
30″ Bottom Mount Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

83 7/8″ 2130 Min.

30″ 765*

(a) Area to be left clear for the anti-tipping brackets ­ 5 1/2″ x 4″ (140×100 mm)
(c) Panel dimensions available on Built-in Food Preservation Design Guide or Installation Manual

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel. * 30 1/8″ (765) for framed-in installation.
bertazzoni.com 89

BOTTOM MOUNT MULTIPLE INSTALLATIONS
90 bertazzoni.com

bertazzoni.com 91

BOTTOM MOUNT MULTIPLE INSTALLATIONS
Bottom Mount Multiple Installations Installation requirements

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.
For panel ready bottom mount, do not exceed the maximum weight of 51 pounds (23 kg) for door panel and 25 pounds (11 kg) for drawer panel. Panel can have thickness ranging between ¾” (19 mm) and 1 1/8″ (28 mm).

TOP VIEW

EW

EW

EW

FRONT VIEW
5″ 127
EW E W EW
A separate circuit breaker servicing only these appliances is recommended.

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

PLUMBING REQUIREMENT
Bertazzoni Bottom Mount refrigerators are provided with a water filter assembly which must be mounted inside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 8 PSI to 75 PSI (between 0.5 bar and 5 bar). Different pressures can cause malfunctions or leaks in the water system.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

92 bertazzoni.com

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 60″ DOUBLE CONFIGURATIONS
60″ Bottom Mount Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF30BMBIXRT REF30BMBIXLT REF30BMBIPRT REF30BMBIPLT
REF30BMBIXRT REF30BMBIXRT REF30BMBIPRT REF30BMBIPRT
REF30BMBIXLT REF30BMBIXLT REF30BMBIPLT REF30BMBIPLT

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

60″ 1524

a Area to be left clear for the anti-tipping brackets ­ 60″x4″ (1524x100mm)
b Depth includes kitchen cabinet front panel

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 93

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 66″ DOUBLE CONFIGURATIONS
66″ Bottom Mount Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF30BMBIXRT REF36BMBIXLT REF30BMBIXLT REF36BMBIXRT REF30BMBIPRT REF36BMBIPLT REF30BMBIPLT REF36BMBIPRT
REF30BMBIXRT REF36BMBIXRT REF30BMBIPRT REF36BMBIPRT
REF30BMBIXLT REF36BMBIXLT REF30BMBIPLT REF36BMBIPLT

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

66″ 1676

a Area to be left clear for the anti-tipping brackets ­ 66″x4″ (1676x100mm)
b Depth includes kitchen cabinet front panel
94 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 72″ DOUBLE CONFIGURATIONS
72″ Bottom Mount Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF36BMBIXRT REF36BMBIXLT REF36BMBIPRT REF36BMBIPLT
REF36BMBIXRT REF36BMBIXRT REF36BMBIPRT REF36BMBIPRT
REF36BMBIXLT REF36BMBIXLT REF36BMBIPLT REF36BMBIPLT

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

72″ 1829

a Area to be left clear for the anti-tipping brackets ­ 72″x4″ (1829x100mm)
b Depth includes kitchen cabinet front panel

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 95

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 48″ DOUBLE CONFIGURATIONS
48″ Double Configurations* Flush installation

POSSIBLE COMBINATIONS c
REF30BMBIPRT REF18WCPRL
REF30BMBIPLT REF18WCPRR

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

48″ 1219

a: Area to be left clear for the anti-tipping brackets ­ 48″x4″ (1219x100mm)
b: Depth includes kitchen cabinet front panel. c: Optional 48 inch bridge toe kick accessory is available.
For details see page 75
96 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

• The combination of bottom mount and wine column is only available for panel ready models.
  All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 54″ DOUBLE CONFIGURATIONS
54″ Double Configurations* Flush installation

POSSIBLE COMBINATIONS
REF30BMBIPRT REF24WCPRL
REF30BMBIPLT REF24WCPRR
REF36BMBIPRT REF18WCPRL
REF36BMBIPLT REF18WCPRR

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

54″ 1372

a Area to be left clear for the anti-tipping brackets ­ 54″x4″ (1372x100mm)
b Depth includes kitchen cabinet front panel

Dimensions in parentheses are millimeters unless otherwise specified. * The combination of bottom mount and wine column is only available for panel ready models. All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.
bertazzoni.com 97

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 60″ DOUBLE CONFIGURATIONS
60″ Double Configurations* Flush installation

POSSIBLE COMBINATIONS
REF36BMBIPRT REF24WCPRL
REF36BMBIPLT REF24WCPRR

TOP VIEW b
25″ 635

FRONT VIEW
a

83 7/8″ 2130 Min.

60″ 1524

a: Area to be left clear for the anti-tipping brackets ­ 60″x4″ (1524x100mm)
b: Depth includes kitchen cabinet front panel.
98 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

• The combination of bottom mount and wine column is only available for panel ready models.
  All Freezer and Wine Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.

BOTTOM MOUNT MULTIPLE INSTALLATIONS – CUSTOM DOOR PANEL
Custom Door Panel

REAR PANEL DRILLING

CUSTOM HANDLES MOUNTING AREA

CUSTOM HANDLE MOUNTING AREA ON LEFT SWING DOOR

83 1/2″ 2120

CUSTOM HANDLE MOUNTING AREA ON RIGHT SWING DOOR

max 11 13/16″ max 300

8 7/8″ 227
28 3/4″ 730

A

B

B

1/2″

4 5/8″

13

117

D

D

48 1/2″ 1233

54 3/4″ 1390

DOOR PANEL

1 3/8″ 34

1 3/8″ 34

3 7/8″

15″ 100

20″ 382

B

B

508

1 3/8″

1/2″

34

13

standard 4″ 100

min 3 1/8″

80

C

C

24 7/8″ 632

D
DRAWER PANEL

CUSTOM HANDLE MOUNTING AREA

36″

30″

A 35 3/4″ (908) 29 3/4″ (756)

B 16 1/2″ (418) 13 1/2″ (343)

C 14″ (354.5) 11″ (279.5)

D 7 1/8″ (182)

6″ (152)

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 99

BOTTOM MOUNT MULTIPLE INSTALLATIONS – REFRIGERATION HANDLES
Refrigeration Handles

PROFESSIONAL SERIES PROHK36PI PROHK30PI
1 1/2″ 37
2 1/8″ 53

MASTER SERIES MASHK36PI MASHK30PI
1 3/4″ 45
2 3/8″ 59

HERITAGE SERIES HERHK36PI HERHK30PI
1 1/4″ 31
2 3/8″ 59

BERTAZZONI HANDLES DRILLING ON RIGHT SWING DOOR
1 5/8″ 42
35 3/8″ 900

BERTAZZONI HANDLES DRILLING ON LEFT SWING DOOR
1 5/8″ 42
35 3/8″ 900

20 1/4″ 514

20 1/4″ 514

HANDLE INSTALLATION ON CUSTOM PANELS
In case a custom panel is to be mounted on any of the models listed below with Bertazzoni handles,it will be necessary to install M5 x 0.8 mm brass tapping inserts in order to secure the handle properly on the custom panel. Recommended drill bit size to drill the pilot hole is 3/8″. Suitable inserts can be ordered at www.encompass.com

Part Number: 95631A100, contains n°4 M5 brass hardwood inserts and 1 M5 installation bit. Do not use a power tool to mount the inserts. Installation of the inserts with improperly calibrated power tools risk damaging the panels.

100 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

V TIER LINE UP
bertazzoni.com 101

BUILT-IN REFRIGERATOR COLUMNS
BUILT-IN COLUMNS Experience the ultimate design and technology with Bertazzoni’s V tier refrigerators and freezer columns. These masterpieces of style boast high-quality materials and attention to detail in all respects. The reversible panel-ready doors() are mounted on cutting-edge Hettich hinges, providing a seamless and weightless range of motion. With versatile installation options, you can create elegant configurations of the refrigerator and freezer columns. You can also customize your columns with optional stainless panels, handles, and finishes, available for every Series.
30″ Panel Ready
() Exept 18″ models. 102 bertazzoni.com

bertazzoni.com 103

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Ready Dimensions
REF30RCBPNV reversible hinges

SIDE VIEW

21 7/8″ 555

FRONT VIEW

83 9/16″ 2123 + 1 9/16″
(40)

74 3/8″ 1890

83 9/16″ 2123 + 1 9/16″
(40)

SIDE VIEW

21 7/8″ 555

FRONT VIEW

83 9/16″ 2123 + 1 9/16″
(40)

74 3/8″ 1890

83 9/16″ 2123 + 1 9/16″
(40)

TOP VIEW

16″ 406
53 7/8″ 1368

29 3/4″ 756

23 5/16″ 592

min 90° max 115°

TOP VIEW

23 5/16″ 592

29 3/4″ 756

min 90° max 115°

16″ 406

53 7/8″ 1368

**

• Depth without door ** Maximum Overall Handle Dimension, 3/4″ (19) Door Panel thickness For custom panel dimensions see page 116 For detailed handle dimensions see page 118
  104 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified. A matching stainless steel panel is available ­ SKU # SP30CX.

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 66 pounds (30 kg) for door panel. Panels can have a thickness ranging between 3/4″ (19 mm) and 1 1/2″ (38 mm). For a flush installation in 25″ deep cabinets, custom door panels should not be thicker than 15/16″ (24 mm).
For instructions of product combinations please see the Multiple Installation Section (page 112).

CABINET REQUIREMENT

Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1200 lb (544 kg)

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.
For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

TOP VIEW

2″

50

WW

EE

FRONT VIEW

8″

200

WW

EE

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 112 W 2 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 90″ power cord

PLUMBING REQUIREMENT
Bertazzoni Refrigerator Columns are provided with a water filter assembly which must be mounted on the bottom part of the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with water dispenser), use a ¼” waterline with accessible shutoff valve. The system pressure must be between from 25 PSI to 80 PSI (between 1.7 and 5.5 Bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see the product spec sheet.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 105

BUILT-IN REFRIGERATOR COLUMNS
30″ Refrigerator Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

84″

30″

2134

762

Min.

(a) Anti-tipping brackets included with appliance ­ 4″x3/16″ (c) Panel dimensions available on Door Panel Specs, Built-in Food
Preservation Design Guide or Installation Manual

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

106 bertazzoni.com

BUILT-IN FREEZER COLUMNS

18″ Panel Ready

bertazzoni.com 107

108 bertazzoni.com

BUILT-IN FREEZER COLUMNS
18″ Freezer Column Panel Ready Dimensions
REF18FCBIPRV left hinge REF18FCBIPRV right hinge

SIDE VIEW

21 7/8″ 555

FRONT VIEW

83 9/16″ 2123 + 1 9/16″
(40)

74 3/8″ 1890

83 9/16″ 2123 + 1 9/16″
(40)

**

TOP VIEW

11″ 280
41 7/8″ 1063

17 3/4″ 451
23 5/16″ 592
min 90° max 115°

SIDE VIEW
” 555

FRONT VIEW

83 9/16″ 2123 + 1 9/16″
(40)

74 3/8″ 90

83 9/16″ 2123 + 1 9/16″
(40)

TOP VIEW

17 3/4″ 451
23 5/16″ 592
min 90° max 115°

11 ” 280

**

41 7/8″ 1063

• Depth without door ** Maximum Overall Handle Dimension, 3/4″ (19) Door Panel thickness For custom panel dimensions see page 116 For detailed handle dimensions see page 118

Dimensions in parentheses are millimeters unless otherwise specified. A matching stainless steel panel is available ­ SKU # SP18CX.
bertazzoni.com 109

BUILT-IN FREEZER COLUMNS
18″ Freezer Column Panel Ready Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliance and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 66 pounds (30 kg) for door panel. Panels can have a thickness ranging between 3/4″ (19 mm) and 1 1/2″ (38 mm). For a flush installation in 25″ deep cabinets, custom door panels should not be thicker than 15/16″ (24 mm).
For instructions of product combinations please see the Multiple Installation Section (page 112).

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.

Required floor support

1200 lb (544 kg)

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.
For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

TOP VIEW

2″

50

WW

EE

FRONT VIEW

8″

200

WW

EE

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 160 W 2 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5 -15P with 90″ power cord

PLUMBING REQUIREMENTS
Bertazzoni Freezer Columns are provided with a water filter assembly which must be mounted on the bottom part of the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with water dispenser), use a ¼” waterline with accessible shutoff valve. The system pressure must be between from 25 PSI to 80 PSI (between 1.7 and 5.5 Bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see the product spec sheet.

Dimensions in parentheses are millimeters unless otherwise specified.

110 bertazzoni.com

BUILT-IN REFRIGERATOR COLUMNS
18″ Freezer Column Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635
FRONT VIEW
aa
18″ 457 84″ 2134 Min.

(a) Anti-tipping brackets included with appliance ­ 4″x3/16″ (c) Panel dimensions available on Door Panel Specs, Built-in Food
Preservation Design Guide or Installation Manual

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

bertazzoni.com 111

COLUMNS MULTIPLE INSTALLATIONS
112 bertazzoni.com

bertazzoni.com 113

MULTIPLE INSTALLATIONS
Multiple installations Installation requirements

INSTALLATION
All Bertazzoni columns can be installed in a standard 25″ depth cutout. Finish the edges of the opening because they may be visible when the door is open. For a built-in installation, to cover gaps between the appliances and the adjacent cabinets, special side profiles are factoryinstalled and covering frames are provided with the product. For panel ready columns, do not exceed the maximum weight of 66 pounds (30 kg) for door panel. Panels can have a thickness ranging between 3/4″ (19 mm) and 1 1/2″ (38 mm). For a flush installation in 25″ deep cabinets, custom door panels should not be thicker than 15/16″ (24m).
For instructions of product combinations please see the Multiple Installation Section (page 112).
CABINET REQUIREMENT
Installation of the appliances must be performed in accordance with the provisions of applicable legislation. Be sure that support of these appliances is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of all the appliances when in use. Please see any single product installation manual for required floor support.
ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

TOP VIEW
E E WW
FRONT VIEW
9″ 229
E E WW
A separate 15 Amp circuit breaker servicing only these appliances is recommended.
PLUMBING REQUIREMENTS
Bertazzoni Refrigerator and Freezer Columns are provided with a water filter assembly which must be mounted on the bottom part of the unit. The appliances must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with water dispenser), use a ¼” waterline with accessible shutoff valve. The system pressure must be between from 25 PSI to 80 PSI (between 1.7 and 5.5 Bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see the product spec sheet.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

114 bertazzoni.com

MULTIPLE INSTALLATIONS – 48″ DOUBLE CONFIGURATIONS
48″ Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF30RCBPNV REF18FCBIP(R/L)V

TOP VIEW b
25″ 635

FRONT VIEW
a

84″ 2134 Min.

48″ 1219

a: Anti-tipping brackets included with appliance ­ 48″x3/16″ b: Depth includes kitchen cabinet front panel.

Dimensions in parentheses are millimeters unless otherwise specified. All Freezer Columns are supplied with a vertical connector trim for multiple columns installations. No additional accessories are needed.
bertazzoni.com 115

CUSTOM HANDLE MOUNTING AREA ON LEFT SWING DOOR

MULTIPLE INSTALLATIONS – CUSTOM DOOR PANEL
Custom Door Panel

REFRIGERATOR COLUMNS REAR PANEL DRILLING

FREEZER COLUMNS REAR PANEL DRILLING

CUSTOM HANDLES MOUNTING AREA

max 11 13/16″ max 300

A

A

B

B

4 3/16″ 107 1 7/8″ 47

2 1/4″ 58 6 5/16″ 160

24 5/16″ 617.5

4″ 102

2 3/16″ 56
6 5/8″ 169

5 1/4″ 134
13/16″ 20 24 5/16″ 617.5

CUSTOM HANDLE MOUNTING AREA ON RIGHT SWING DOOR

83 9/16″ 2123

79 15/16″ 2030

1 7/8″ 47 7 1/4″ 184

2 1/4″ 58 6 5/16″ 160

standard 4″ 100

min 3 1/8″ 80

1 1/16″ 27

11/16″ 18

1 1/16″ 27

11/16″ 18

1 1/16″ 27

11/16″ 18

1 1/16″ 27

11/16″ 18

27 5/16″ 694.5
2 3/4″ 70 7 1/16″ 179

6 1/8″ 155

27 5/16″ 694.5

30″

A

29 3/4″ (756)

B

6″ (152)

18″ 17 3/4″ (451)
3 5/8″ (92)

116 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

MULTIPLE INSTALLATIONS – RECOMMENDED INSTALLATIONS
Recommended Installations
RECOMMENDED INSTALLATIONS NOT RECOMMENDED INSTALLATIONS
bertazzoni.com 117

MULTIPLE INSTALLATIONS – REFRIGERATION HANDLES
Refrigeration Handles

PROFESSIONAL SERIES PROHKCOL
1 1/2″ 37
2 1/8″ 53

MASTER SERIES MASHKCOL
1 3/4″ 45
2 3/8″ 59

HERITAGE SERIES HERHKCOL
1 1/4″ 31
2 3/8″ 59

BERTAZZONI HANDLES DRILLING ON RIGHT SWING DOOR
1 5/8″ 42
35 3/8″ 900

BERTAZZONI HANDLES DRILLING ON LEFT SWING DOOR
1 5/8″ 42
35 3/8″ 900

20 1/4″ 514

20 1/4″ 514

HANDLE INSTALLATION ON CUSTOM PANELS
In case a custom panel is to be mounted on any of the models listed below with Bertazzoni handles,it will be necessary to install M5 x 0.8 mm brass tapping inserts in order to secure the handle properly on the custom panel. Recommended drill bit size to drill the pilot hole is 3/8″. Suitable inserts can be ordered at www.encompass.com

Part Number: 95631A100, contains n°4 M5 brass hardwood inserts and 1 M5 installation bit. Do not use a power tool to mount the inserts. Installation of the inserts with improperly calibrated power tools risk damaging the panels.

118 bertazzoni.com

Dimensions in parentheses are millimeters unless otherwise specified.

BUILT-IN BOTTOM MOUNT REFRIGERATORS

Experience the perfect combination of design and technology with Bertazzoni’s Premium tier refrigerators. These masterpieces of style reflect our meticulous attention to detail and are designed to retain your food’s nutritional value, vitamins, minerals, and texture for longer. With a true flush installation in a standard depth cabinet and reversible panel-ready doors, they seamlessly integrate with any adjacent cabinetry. You can even install them side-by-side with CTXV connection kit, doubling your refrigerator space. Customize your refrigerators with optional stainless panels and Professional, Master, or Heritage Series handles to match your other kitchen appliances. Our 36″ and 30″ bottom-mount models feature Hettich hinges that allow a minimal vertical gap of 1/8″ between adjacent front cabinet panels, creating clean lines in your kitchen.

36″ Panel Ready

30″ Panel Ready

bertazzoni.com 119

131 bertazzoni.com

BUILT-IN BOTTOM MOUNT
36″ Bottom Mount Panel Ready Dimensions
REF36BMBZPNV reversible hinge
Handle choices Professional Series: PROHK36PI Master series: MASHK36PI Heritage Series: HERHK36PI

SIDE VIEW

40 3/8″ 1026

21 7/8″ 555

FRONT VIEW

83 9/16″ 2123 + 1 9/16″
(40)

SIDE VIEW

40 3/8″ 1026

21 7/8″ 555

FRONT VIEW

83 9/16″ 2123 + 1 9/16″
(40)

• Maximum Overall Handle Dimension ** 15/16″ (24mm) Door Panel thickness For custom panel dimensions see page 137 For detailed handle dimensions see page 138
  124 bertazzoni.com

TOP VIEW

51 1/16″ 1297
1/8″ 3
28 11/16″ 729

19″ 483

**

61″ 1549

4″ 100

+ 1 9/16″ (40)

TOP VIEW

35 3/4″ 908

23 5/16″ 592

min 90° max 115°

51 1/16″ 1297
1/8″ 3
28 11/16″ 729

23 5/16″ 592

35 3/4″ 908

min 90° max 115°

19″ 483
61″ 1549

4″ 100

+ 1 9/16″ (40)

Dimensions in parentheses are millimeters unless otherwise specified. A matching stainless steel panel is available – SKU # SP36BMX.

BUILT-IN BOTTOM MOUNT
36″ Bottom Mount Panel Ready Installation requirements

CABINET REQUIREMENT

TOP VIEW

2″

50

Installation of the appliance must be performed in accordance

WW

EE

with the provisions of applicable legislation.

Be sure that support of this appliance is perpendicular to the

front facing of the wall or cabinet before you perform the

FRONT VIEW

installation.

The floor must be flat and must be capable of supporting the

8″ 200

weight of the appliance when in use.

WW

EE

Required floor support

1200 lb (544 kg)

For panel ready bottom mount refrigerator, do not exceed the maximum weight of 35 pounds (16 kg) for door panel and 20 pounds (9 kg) for drawer panel. Panels can have a thickness ranging between 3/4″ (19 mm) and 1 1/2″ (38 mm). For a flush installation in 25″ deep cabinets, custom door panels should not be thicker than 15/16″ (24 mm).

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 120 W 3 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5-15P with 90″ power cord

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

PLUMBING REQUIREMENT
Bertazzoni Bottom Mount refrigerators are provided with a water filter assembly which must be mounted inside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 25 to 80 PSI (between 1.7 and 5.5 bar). Different pressures can cause malfunctions or leaks in the water system.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 125

BUILT-IN BOTTOM MOUNT
36″ Bottom Mount Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

36″ 914
84″ 2134 Min.

(a) Anti-tipping brackets included with appliance ­ 4″x3/16″ (c) Panel dimensions available on Door Panel Specs, Built-in Food
Preservation Design Guide or Installation Manual

Dimensions in parentheses are millimeters unless otherwise specified.

126 bertazzoni.com

BUILT-IN BOTTOM MOUNT
30″ Bottom Mount Panel Ready Dimensions

REF30BMBZPNV reversible hinge REF30BMBPNB reversible hinge
Handle choices Professional Series: PROHK30PI Master series: MASHK30PI Heritage Series: HERHK30PI

SIDE VIEW

40 3/8″ 1026

21 7/8″ 555

FRONT VIEW

83 9/16″ 2123 + 1 9/16″
(40)

51 1/16″ 1297
1/8″ 3
28 11/16″ 729

TOP VIEW

14 5/8″ 371
55 1/2″ 1409

29 3/4″ 756

23 5/16″ 592

min 90° max 115°

SIDE VIEW

40 3/8″ 1026

21 7/8″ 555

FRONT VIEW

4″ 100

+ 1 9/16″ (40)

TOP VIEW

83 9/16″ 2123 + 1 9/16″
(40)

51 1/16″ 1297
1/8″ 3
28 11/16″ 729

23 5/16″ 592

29 3/4″ 756

min 90° max 115°

14 5/8″ 371
55 1/2″ 1409

4″ 100

+ 1 9/16″ (40)

• Maximum Overall Handle Dimension ** 15/16″ (24mm) Door Panel thickness For custom panel dimensions see page 137 For detailed handle dimensions see page 138

Dimensions in parentheses are millimeters unless otherwise specified. A matching stainless steel panel is available – SKU # SP30BMX.
bertazzoni.com 127

BUILT-IN BOTTOM MOUNT
30″ Bottom Mount Panel Ready Installation requirements

CABINET REQUIREMENT

TOP VIEW

2″

50

WW

EE

Installation of the appliance must be performed in accordance

with the provisions of applicable legislation.

Be sure that support of this appliance is perpendicular to the

front facing of the wall or cabinet before you perform the FRONT VIEW

installation.

The floor must be flat and must be capable of supporting the

8″ 200

weight of the appliance when in use.

WW

EE

Required floor support

1200 lb (544 kg)

For panel ready combi bottom mount, do not exceed the maximum weight of 35 pounds (16 kg) for door panel and 20 pounds (9 kg) for drawer panel. For a flush installation, cabinet panels should not be thicker than 15/16″ (24 mm).

A separate circuit breaker servicing only this appliance is recommended.

Electrical supply 115 V 60 Hz 120 W 3 Amp

Service

15 Amp dedicated circuit

Power Connection NEMA 5-15P with 90″ power cord

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

PLUMBING REQUIREMENT
Bertazzoni Bottom Mount refrigerators are provided with a water filter assembly which must be mounted inside the unit. The appliance must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with ice maker) a ¼” waterline with accessible shut-off valve must be supplied. The solenoid connection on the appliance is ¾” diameter but is metric threaded (NPT). The system pressure must be between from 25 to 80 PSI (between 1.7 and 5.5 bar). Different pressures can cause malfunctions or leaks in the water system.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

128 bertazzoni.com

BUILT-IN REFRIGERATOR COLUMNS
30″ Bottom Mount Panel Ready Flush installation

SIDE VIEW
c

TOP VIEW b
25″ 635

FRONT VIEW

a

a

84″

30″

2134

762

Min.

(a) Anti-tipping brackets included with appliance ­ 4″x3/16″ (c) Panel dimensions available on Door Panel Specs, Built-in Food
Preservation Design Guide or Installation Manual

Dimensions in parentheses are millimeters unless otherwise specified. b: depth includes kitchen cabinet front panel.

bertazzoni.com 129

BOTTOM MOUNTS MULTIPLE INSTALLATIONS
130 bertazzoni.com

131 bertazzoni.com

BOTTOM MOUNT MULTIPLE INSTALLATIONS
Bottom Mount Multiple installations Installation requirements

CABINET REQUIREMENT
Installation of the appliance must be performed in accordance with the provisions of applicable legislation. Be sure that support of this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation. The floor must be flat and must be capable of supporting the weight of the appliance when in use.
For panel ready bottom mount, do not exceed the maximum weight of 35/44 pounds (16/20 kg) for door panel/s and 20 pounds (9 kg) for drawer panel. Panels can have a thickness ranging between 3/4″ (19 mm) and 1 1/2″ (38 mm). For a flush installation in 25″ deep cabinets, custom door panels should not be thicker than 15/16″ (24 mm).

TOP VIEW
E E WW
FRONT VIEW
9″ 229
E E WW
A separate circuit breaker servicing only these appliances is recommended.

ELECTRICAL REQUIREMENT
The installation must comply with all applicable electrical codes. A properly- grounded horizontally-mounted electrical receptacle should be installed. Place the electrical supply flush with the back wall and within the shaded area shown in the illustrations. Placement within the opening may require additional cabinet depth.

PLUMBING REQUIREMENT
The appliances must be connected only to a potable water supply system. To connect to water supply system (for appliances equipped with water dispenser), use a ¼” waterline with accessible shutoff valve. The system pressure must be between from 25 PSI to 80 PSI (between 1.7 and 5.5 Bar). Different pressures can cause malfunctions or leaks in the water system. For information on how to purchase the water filter, please see the product spec sheet.

For detailed installation specifications consult the multiple installation requirements page or each single product installation manual.

Dimensions in parentheses are millimeters unless otherwise specified.

132 bertazzoni.com

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 60″ DOUBLE CONFIGURATIONS
60″ Bottom Mount Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF30BMBZPNV REF30BMBZPNV
REF30BMBPNB REF30BMBPNB

TOP VIEW b
25″ 635

FRONT VIEW
a

84″ 2134 Min.

60″ 1524

a Anti-tipping brackets included with appliance ­ 60″x3/16″ b Depth includes kitchen cabinet front panel

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 133

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 66″ DOUBLE CONFIGURATIONS
66″ Bottom Mount Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF30BMBZPNV REF36BMBZPNV

TOP VIEW b
25″ 635

FRONT VIEW
a

84″ 2134 Min.

66″ 1676

a Anti-tipping brackets included with appliance ­ 66″x3/16″ b Depth includes kitchen cabinet front panel

Dimensions in parentheses are millimeters unless otherwise specified.

134 bertazzoni.com

BOTTOM MOUNT MULTIPLE INSTALLATIONS – 72″ DOUBLE CONFIGURATIONS
72″ Bottom Mount Double Configurations Flush installation

POSSIBLE COMBINATIONS
REF36BMBZPNV REF36BMBZPNV

TOP VIEW b
25″ 635

FRONT VIEW
a

84″ 2134 Min.

72″ 1829

a Anti-tipping brackets included with appliance ­ 72″x3/16″ b Depth includes kitchen cabinet front panel

Dimensions in parentheses are millimeters unless otherwise specified.

bertazzoni.com 135

BOTTOM MOUNT MULTIPLE INSTALLATIONS – CUSTOM DOOR PANEL
Bottom Mount Custom Door Panel

CUSTOM HANDLE MOUNTING AREA ON LEFT SWING DOOR

36″ & 30″ BOTTOM MOUNT REAR PANEL DRILLING

CUSTOM HANDLES MOUNTING AREA

max 11 13/16″ max 300

4 13/16″ 123

B
2 3/4″ 70

A 2″ 50

11/16″ 18

2 7/8″ 72.5

B

C

C

CUSTOM HANDLE MOUNTING AREA ON RIGHT SWING DOOR

standard 4″ 100

51 1/16″ 1297

2 3/4″ 70

4 13/32″ 112 1 1/8″ 28

B 9 15/16″ 253

3 1/8″ 79

B 2″ 50
2 7/16″ 61.5

13/16″ 20 13/16″ 20

C

3 5/64″ 78

28 11/16″ 729

5 15/16″ 148
min 3 1/8″ 80

11/16″ 18 2″ 50

11/16″ 18

DOOR PANEL
CUSTOM HANDLE MOUNTING AREA DRAWER PANEL

36″

30″

A

35 3/4″ (908)

29 3/4″ (756)

B

5 1/2″ (139)

2 1/2″ (63)

C

7 1/8″ (182)

6″ (152)

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 137

BOTTOM MOUNT MULTIPLE INSTALLATIONS – REFRIGERATION HANDLES
Bottom Mount Refrigeration Handles

PROFESSIONAL SERIES PROHK36PI PROHK30PI
1 1/2″ 37
2 1/8″ 53

MASTER SERIES MASHK36PI MASHK30PI
1 3/4″ 45
2 3/8″ 59

HERITAGE SERIES HERHK36PI HERHK30PI
1 1/4″ 31
2 3/8″ 59

BERTAZZONI HANDLES DRILLING ON RIGHT SWING DOOR
1 5/8″ 42
35 3/8″ 900

BERTAZZONI HANDLES DRILLING ON LEFT SWING DOOR
1 5/8″ 42
35 3/8″ 900

20 1/4″ 514

20 1/4″ 514

HANDLE INSTALLATION ON CUSTOM PANELS
In case a custom panel is to be mounted on any of the models listed below with Bertazzoni handles,it will be necessary to install M5 x 0.8 mm brass tapping inserts in order to secure the handle properly on the custom panel. Recommended drill bit size to drill the pilot hole is 3/8″. Suitable inserts can be ordered at www.encompass.com

Part Number: 95631A100, contains n°4 M5 brass hardwood inserts and 1 M5 installation bit. Do not use a power tool to mount the inserts. Installation of the inserts with improperly calibrated power tools risk damaging the panels.

Dimensions in parentheses are millimeters unless otherwise specified.
bertazzoni.com 139

BERTAZZONI.COM TO COOK BEAUTIFULLY
140 bertazzoni.com

References

• BERTAZZONI - Premium Kitchen Appliances - UK
• BERTAZZONI - Premium Kitchen Appliances - Canada
• BERTAZZONI - Premium Kitchen Appliances - United States
• Encompass Parts: Replacement OEM Parts and Accessories
• Encompass Parts: Replacement OEM Parts and Accessories

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>