Wayfair G37016 Metal Garden Shed Instruction Manual
- June 15, 2024
- wayfair
Table of Contents
MANUAL INSTRUCTION
Metal Garden Shed 3’X5’FT
G37016 Metal Garden Shed 3’X5′ FT G37016
We offer a diverse range of products to meet the needs of customers.
Outdoor Furniture
We are a professional furniture provider with top-notch factories and
outstanding designs, Our mission is to provide consumers with new lifestyles.
By collecting consumer feedback, we constantly improve our products and create
more choices for consumers. If you want to create your space, We are anideal
choice.
Always.
Thank you for your purchase our product.
- If there is any damage, please kindly send clear photos of damaged parts to us as aftachment, we will check and offer you best solution soon.
- We attach greatimportance fo the customer experience of our products. If there’s any concern,please contact us at any time, we will provide effective solutions.
- Itisrecommended to finish assembling by more than two people, so that it will be easier and also save your time.
Attention
Please read this instruction carefully before installation and strictly follow
it during installation. Ensure that there will be no problems in the future
due fo installation errors.
Installation Notes
Please check the quantity of all parts before installation (Please refer to
the Parts Lists) and the appearance of the products. Please make sure the
product is correct before installation. If there is any problem, please
contact us directly.
Make sure the colored panels are facing outwards and all the holes match. The
panels are textured,please install the panels in the order specified in the
instructions. All lines and holes must be accurately matched to make the
storage shed more stable. Please ensure that all screws are tightened to
prevent the product from falling apart.
There is a protective film on the surface fo protect the product, please tear
it off after installation to get the final presentation. If you do not damage
the film during installation, it can also remain on the product to protect the
product.
Please place the product on a flat ground to prevent leaning and collapse. If
the ground is uneven, the door may can’t be closed
Safety Precautions
- We recommend two adults to complete the installation.Two adults installed together will make the installation process easier and safer.
- The gloves must be carried to prevent hand cuts during installation.
- Take care when using power tools near water the use of aresidual current device(RCD) is advised.
- Please use the electric driver carefully during screwing to prevent the screw from slipping and hurting your hand.(We recommend that beginners use a manual screwdriver for installation.)
- Be careful not fo fall when installing the roof. Please steady the ladder and make sure the product placed on a flat ground.
WARNING
- For your safety concern,please do not stand under the metal shed in heavy wind or snow days.
- For safety, please use expansion screws to reinforce the posts to the ground.
- In extreme weather conditions,you can use a rope to pull the four corners of the gazebo to keep it stable.
- Please clear the snow off the roof in time for the heavy snowfall. Make sure all screws are tightened before use.
- Repeat to confirm all screws, buckles and straps every 90 days. Please keep all screws loose during the assembly process and tighten them after completing the installation.
- Do not use or store objects in the Metal Shed with open flames or flammable chemicals.
- Please note that some parts have sharp edges and should be handled with gloves.
- If any parts are missing, broken, damaged or worn, discontinue use of the product until repairs are made or factory replacement parts are installed.
- Installation of the product in a manner that does not conform to the manufacturer’sinstructions may result in the loss of the warranty policy for this product.
CALIFORNIA PROPOSITION 65
WARNING: This product can expose you to Carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
PARTS Before installation, please place the parts in the position as shown inthe figure below.
Shed top panels
No.| QTY
K34-8| 2
K34-8M| 1
K34-8MM| 1
K34-10| 2
K349| 2
GC| 4
Shed top panels
No.| QTY
K34-4| 2
K34-6L| 1
K34-6R| 1
K34-7| 1
K34-4| 1
K34-5| 1
c2| 4
GF| 2
Shed top panels
No.| QTY
W5| 4
W5-C| 4
W5-X| 1
W3-HX| 1
URA| 1
ULA| 1
DRA1| 1
DD| 2
DX1| 1
DLAT| 1
K34-1| 2
K34-2| 2
TF| 4
TOOLS REQUIRED
| Electeic Screwdriver
---|---
| +Manual Screwdriver
| Landder
2-4 Persons Assembly
Up to 120 minutes For Assembly
PACKAGE C PART LIST
PACKAGE AB PART LIST
PRODUCT ASSEMBLY
- STEP1:Shed Base Frame Assemble
Link the two “K34-1” and “K34-2″ to each other, and reinforce the four corners with”T-F”.
PART | NO. | QTY. |
---|---|---|
K34-1 | 2 | |
K34-2 | 2 | |
T-F | 4 | |
F1 | 24 |
Note: The larger hole is aways covered over the small hole.
- STEP2:Shed Side Panels Assemble
Mount the 4 “W5-C” on the Shed Base Frame Assemble as shown.
7 STEP7:Install “ULA” on the left side of the door frame and “URA” on the right side of the door frame.
8 STEP8:1.Install the “GF” window in the position shown in the figure.
2.Shed Top Frame Assemble”K34-6L” is mounted on the top left “K34-6R” is
mounted on the top right
12 STEP12:1 .Install hemming “K34-9” on both sides of the roof.
2.Connect and install K34-10 on the rear side of the roof.
3.Connect and install K34-10 on the front side of the roof
4.Install the comer “GC” on the four corners of the roof.t
Door Assemble
13 STEP13:1.Assemble “W5-X” and “W3-HX” together using “F2”
2.Install “DD””‘DLAT” and “DRA1” around the door.
3.Install “DX1” on the inside of the door for reinforcement as shown in the
figure.
Note: View from the front, the vertical rod covers the horizontal rod.The larger hole is always covered over the small hole.
14 STEP14:1 .Install the two “DH” hinges on one side of the door using 8 “F3”
screws
2.Use 6 “F2” screws to fasten the “DCS” part fo the door as shown
STEP15:1 .Use 8 “F3” screws to mount the door in the position shown
3.Use 2 “F2” screws to mount the “DCS” part in the position shown
15 STEP15:The exposed parts of the screws need to be covered with plastic protective caps.Screw positions:Exposed parts of ceiling and k34-7 assembly screws.
HELP CENTER
Question about your product? We’re here to help. Visit us at:
We Stands Behind the Quality of Their Furniture
If you have any issues with your item please let us know! We will always do
our best o come up with a solution that you will be happy with.
Please get in fouch with our customer service team before returning the
product.
And pls do not throw the original box(es) if you have not finished assembling
or confirmed no quality issues.
Length of return period:
Ilems can be returned within 30 days of purchase.
Inthe meanwhile, everything you purchased from us comes with a one-year
warranty.
Who is responsible for the refurn shipping fee:
We will cover the return shipping fees if:
-
Your item has a manufacturing defect in its materials or workmanship.
For example, forn wicker or misaligned screw holes. We will send you a prepaid shipping label affer photos are sent. -
Your item has been damaged in transit.
For example, glass is broken or wicker is damaged.
We will send you a prepaid shipping label after photos are sent. -
You receive the wrong box(es) due fo @ warehouse error. We will send you a prepaid shipping label after photos are sent of the wrong SKU numbers on the outer box(es).
-
0ne or more boxes are lost in transit. We will send you a prep« hipping label if you no longer want the item.
*However, we still hope to work with you for a better solution instead of a return. Please don’t hesitate fo contact our customer service team.
Customer will cover the return shipping fees if:
- You don’t like the product(s) affer receiving the box(es).
- You no longer need the product(s) but you have received fhe box(es)
- You buy the product(s) by mistake but you have received the box(es).
- 0rder/Shipment cancellation failed and you have received the box(es).
Return Request
In order fo get a full refund as described in this return policy. all items
must be: (1) In a brand new/unused condifion, please provide photos before and
affer packaging. (2) When returning, all accessories and parts are firmly
packed in all original packaging.
If your return does not meet the requirements, you may not get a full refund.
When will | be refunded?
The refund is released once the goods have been returned to our warehouse.
What if the product is damaged/defective outside of the valid return period?
We want you fo be a happy customer. Please reach out fo us by email and we
will come up with a solution to make sure you are satisfied.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>