Showtec S-1200 Snow Machine User Manual

June 15, 2024
Showtec

S-1200 Snow Machine

Product Information

Specifications

  • Product Name: Stellar S-1200 Snow Machine V1
  • Product Code: 61115

Introduction

The Stellar S-1200 Snow Machine is a high-quality product
designed to create artificial snow effects. This user manual
provides instructions for the correct and safe use of the product.
Please read and follow the instructions carefully to ensure proper
installation, operation, and maintenance.

Important Safety Instructions

Before using the product, it is essential to read and understand
the safety instructions provided in this user manual. Failure to
follow these instructions may result in serious injuries or damage
to property. Please adhere to the following safety guidelines:

  • Always operate the snow machine in a well-ventilated area.

  • Do not expose the snow machine to water or moisture.

  • Keep the snow machine away from flammable materials or
    substances.

  • Ensure that the power supply meets the requirements specified
    in this manual.

  • Do not attempt to modify or repair the snow machine yourself.
    Contact an authorized service provider for assistance.

Requirements for the User

To use the Stellar S-1200 Snow Machine safely and effectively,
please ensure that you meet the following requirements:

  • Read and understand this user manual.

  • Follow all safety instructions provided in this manual.

  • Ensure that the power supply voltage is compatible with the
    snow machine’s requirements (refer to specifications).

  • Place the snow machine on a stable and level surface.

  • Keep the snow machine away from children and unauthorized
    personnel.

Accessories

The Stellar S-1200 Snow Machine comes with the following
accessories:

  • Schuko to Power Pro cable (1.5 m)
  • User manual

Dimensions

The dimensions of the Stellar S-1200 Snow Machine are as
follows:

  • Length: [insert length]
  • Width: [insert width]
  • Height: [insert height]

Troubleshooting

If you encounter any issues with the Stellar S-1200 Snow
Machine, please refer to the troubleshooting section in this user
manual. It provides solutions to common problems you may experience
during operation.

Disposal

When the snow machine reaches the end of its lifespan or is no
longer needed, it should be disposed of properly. Follow the
disposal instructions provided in this manual to ensure
environmentally friendly disposal.

Approval

The Stellar S-1200 Snow Machine has received the necessary
approvals to meet safety standards. For more information about the
product’s approval, refer to the approval section in this user
manual.

Frequently Asked Questions (FAQ)

  1. 1. Q: Can I use the snow machine outdoors?

A: The snow machine is designed for indoor use only. Using it
outdoors may cause damage or malfunction.

  1. 1. Q: How do I clean the snow machine?

A: Follow the maintenance procedures provided in this user
manual to clean the snow machine. Use a soft cloth and mild
cleaning solution to remove any dirt or residue.

  1. 1. Q: Can I use the snow machine without the included cable?

A: No, the snow machine requires the Schuko to Power Pro cable
included in the package for proper operation. Using a different
cable may result in compatibility issues.

USER MANUAL

ENGLISH

Stellar S-1200 Snow Machine V1
Product code: 61115

Highlite International B.V. ­ Vestastraat 2 ­ 6468 EX ­ Kerkrade ­ the Netherlands

Stellar S-1200 Snow Machine
Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
This user manual contains information concerning:
Safety instructions Installation and operation of the device Intended and non- intended use of the device Maintenance procedures Troubleshooting Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of property.

©2023 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or other language versions, please visit our website www.highlite.com or contact us at service@highlite.com.
Highlite International and its authorized service providers are not liable for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or reliance on the information contained in this document.

Product code: 61115

1

Stellar S-1200 Snow Machine
Table of contents
1. Introduction……………………………………………………………………………………………………………………………………….4 Before Using the Product ………………………………………………………………………………………………………………….4 Intended Use …………………………………………………………………………………………………………………………………….4 Product Lifespan……………………………………………………………………………………………………………………………….4 Text Conventions ………………………………………………………………………………………………………………………………4 Symbols and Signal Words………………………………………………………………………………………………………………..5 Symbols on the Information Label ……………………………………………………………………………………………………5
2. Safety ………………………………………………………………………………………………………………………………………………..6 Warnings and Safety Instructions ……………………………………………………………………………………………………..6 Requirements for the User…………………………………………………………………………………………………………………9
3. Description of the Device …………………………………………………………………………………………………………………10 Front View ……………………………………………………………………………………………………………………………………….10 Back View ……………………………………………………………………………………………………………………………………….11 Product Specifications ……………………………………………………………………………………………………………………12
3.4. Accessories ……………………………………………………………………………………………………………………………………..12 Dimensions ………………………………………………………………………………………………………………………………………13
4. Installation and Setup ………………………………………………………………………………………………………………………14 Safety Instructions for Installation ……………………………………………………………………………………………………14 Personal Protective Equipment ………………………………………………………………………………………………………14 Installation Site Requirements …………………………………………………………………………………………………………14 Rigging ……………………………………………………………………………………………………………………………………………14 Connecting to Power Supply………………………………………………………………………………………………………….16
5. Setup ……………………………………………………………………………………………………………………………………………….17 Warnings and Precautions ……………………………………………………………………………………………………………..17 Stand-alone Setup ………………………………………………………………………………………………………………………….17 DMX Connection…………………………………………………………………………………………………………………………….17 DMX-512 Protocol …………………………………………………………………………………………………………………..17 DMX Cables……………………………………………………………………………………………………………………………18 DMX Linking ……………………………………………………………………………………………………………………………18 DMX Addressing……………………………………………………………………………………………………………………..19
6. Operation ………………………………………………………………………………………………………………………………………..20 Safety Instructions for Operation …………………………………………………………………………………………………….20 Recommended Snow Fluid …………………………………………………………………………………………………………….20 Filling the Tank …………………………………………………………………………………………………………………………………21 Emptying the Tank after Operation ………………………………………………………………………………………………..23 Restarting the Device after Running the Tank empty …………………………………………………………………….24 Control Modes ………………………………………………………………………………………………………………………………..24 Manual Operation ………………………………………………………………………………………………………………………….25 Control Panel (Device)…………………………………………………………………………………………………………..25 Start-up …………………………………………………………………………………………………………………………………..26 Menu Overview ……………………………………………………………………………………………………………………..26 Main Menu Options ……………………………………………………………………………………………………………….27 DMX Address ………………………………………………………………………………………………………………………27 Snow Volume ……………………………………………………………………………………………………………………..27 Wind Speed ………………………………………………………………………………………………………………………..27 DMX Mode………………………………………………………………………………………………………………………….28 Interval ………………………………………………………………………………………………………………………………..28 Duration………………………………………………………………………………………………………………………………28 Timer ……………………………………………………………………………………………………………………………………28 Timer Mode …………………………………………………………………………………………………………………………….29 DMX Control Mode ………………………………………………………………………………………………………………..29 Manual Mode ………………………………………………………………………………………………………………………..30 DMX Operation……………………………………………………………………………………………………………………………….30

Product code: 61115

2

Stellar S-1200 Snow Machine
DMX Channels ………………………………………………………………………………………………………………………………..31 1 Channel ………………………………………………………………………………………………………………………………31 3 Channels ……………………………………………………………………………………………………………………………..31 5 Channels ……………………………………………………………………………………………………………………………..31
7. Troubleshooting ……………………………………………………………………………………………………………………………….32
8. Maintenance …………………………………………………………………………………………………………………………………..33 Safety Instructions for Maintenance……………………………………………………………………………………………….33 Preventive Maintenance ………………………………………………………………………………………………………………..33 Basic Cleaning Instructions …………………………………………………………………………………………………….33 Cleaning the Fluid Pipes…………………………………………………………………………………………………………34 Corrective Maintenance ………………………………………………………………………………………………………………..34 Replacing the Fuse ………………………………………………………………………………………………………………..34
9. Deinstallation, Transportation and Storage ……………………………………………………………………………………….35 Instructions for Deinstallation…………………………………………………………………………………………………………..35 Instructions for Transportation …………………………………………………………………………………………………………35 Storage ……………………………………………………………………………………………………………………………………………35
10. Disposal …………………………………………………………………………………………………………………………………………..35
11. Approval………………………………………………………………………………………………………………………………………….35

Product code: 61115

3

Stellar S-1200 Snow Machine
1. Introduction
Before Using the Product
Important Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: Showtec Stellar S-1200 Snow Machine Schuko to Power Pro cable (1,5 m) User manual

Fig. 01

Intended Use

This device is designed to be used as a professional snow machine. Any incorrect use may lead to hazardous situations and result in injuries and material damage. This device is not suitable for households.

Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

Product Lifespan

This device is not designed for permanent operation. Disconnect the device from the electrical power supply when the device is not in operation. This will reduce the wear and will improve the device’s lifespan.

Text Conventions

Throughout the user manual the following text conventions are used:

Buttons: References:
0­255: Notes:

All buttons are in bold lettering, for example “Press the UP/DOWN buttons” References to chapters and parts of the device are in bold lettering, for example: “Refer to 2. Safety”, “turn the adjustment screw (02)” Defines a range of values Note: (in bold lettering) is followed by useful information or tips

Product code: 61115

4

Stellar S-1200 Snow Machine

Symbols and Signal Words

Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual.

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

Attention

Indicates important information for the correct operation and use of the product.

Important Read and observe the instructions in this document.

Electrical hazard

Hot surface

Provides important information about the disposal of this product.

Symbols on the Information Label
This product is provided with an information label. The information label is located on the backside of the device.
The information label contains the following symbols:

This device shall not be treated as household waste.

This device is designed for indoor use. Read the user manual supplied with the device. This device falls under IEC protection class I.

Product code: 61115

5

Stellar S-1200 Snow Machine
2. Safety
Important Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
Warnings and Safety Instructions
DANGER Danger for children
For adult use only. The device must be installed beyond the reach of children.
Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within children’s reach. Packaging material is a potential source of danger for children.
DANGER Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage (> 120 V DC) may be present.
Do not open the device or remove any covers. Do not operate the device if the covers or the housing are open. Before operation, check if the
housing is firmly closed and all screws are tightly fastened. Disconnect the device from electrical power supply before service and maintenance, and when the
device is not in use.
DANGER Electric shock caused by short-circuit
This device falls under IEC protection class I.
Make sure that the device is electrically connected to ground (earth). Connect the device only to a socket-outlet with ground (earth) connection.
Do not cover the ground (earth) connection. Do not bypass the thermostatic switch or fuses. For replacement use fuses of the same type and rating only. Do not let the power cable come into contact with other cables. Handle the power cable and all
connections with the mains with caution. Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable. Make sure that the power cable is not crimped or damaged. Examine the power cable periodically
for any defects. Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur. Do not use the device during thunderstorms. Disconnect the device from the electrical power supply
immediately.

Product code: 61115

6

Stellar S-1200 Snow Machine
Do not point the snow output directly at persons or animals. Make sure that persons cannot come closer than 50 cm to the snow output nozzle.
WARNING Risk of explosion caused by incorrect handling
Do not add flammable liquids such as perfume and alcohol to the snow fluid. Operate the device only with the fluids recommended in this user manual.
CAUTION Risk of health problems
Operate the device only with the fluids recommended in this user manual. Other fluids may contain substances, which are hazardous for human health and environment.
Always refer to the Safety Data Sheet (SDS) of the fluid before to use. Do not swallow the fluid. Do not point the snow output at face height. Make sure that you use the device in spaces that have good airflow. Persons, who suffer from respiratory disorders, should avoid prolonged exposure to artificially produced atmospheric effects.
Attention Risk of fire
Do not point the snow output at flames. Keep flammable and heat-sensitive objects at a minimum distance of 50 cm from the snow output
nozzle. Do not cover the air vents. Make sure that there is sufficient airflow around the device.

Product code: 61115

7

Stellar S-1200 Snow Machine
Attention Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.
Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the required power consumption of the device.
Attention General safety
Do not operate the device without liquid. Do not point the snow output at smooth floors. The snow output can cause condensation, which can
make the floor slippery. Do not insert objects into the air vents. Do not switch the device on and off in short intervals. This decreases the device’s life. Do not shake the device. Avoid brute force when installing or operating the device. If the device is dropped or struck, disconnect the device from the electrical power supply
immediately. If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it
on immediately. Let the device reach room temperature before switching it on, otherwise it may be damaged by the formed condensation. If the device fails to work properly, discontinue the use immediately.
Attention For professional use only This device shall be used only for the purposes it is designed for.
This device is designed to be used as a professional snow effect. Any incorrect use may lead to hazardous situations and result in injuries and material damage.
This device is not suitable for households. This device is not designed for permanent operation. This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.
Attention Before each use, examine the device visually for any defects.
Make sure that:
The fluid tank is closed. All screws used for installing the device or parts of the device are tightly fastened and are not
corroded. The safety devices are not damaged. There are no deformations on housings, fixations and installation points. The power cables are not damaged and do not show any material fatigue.

Product code: 61115

8

Stellar S-1200 Snow Machine
Attention Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater than 12 mm, such as fingers, and no protection against harmful ingress of water.
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons. Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled person, for specific tasks and work activities associated with the installation, service and maintenance of this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons include not only users of the product but also any other persons that may have access to the device or who may be in the vicinity of the device.

Product code: 61115

9

Stellar S-1200 Snow Machine
3. Description of the Device
The Stellar S-1200 is a snow machine. It can be controlled manually with the help of a clear LCD display, via DMX or with an optional remote control. For best results, we recommend using Showgear snow liquid or concentrate.
Front View

  1. Mounting bracket 02) Snow liquid tank (5 L) 03) Snow output nozzle 04) Carrying handle 05) Adjustment screw

Product code: 61115

10

Fig. 02

Stellar S-1200 Snow Machine Back View

  1. LCD display + control buttons 07) 5-pin DMX connector OUT 08) ON/OFF switch 09) Fuse F8A / 250 V 10) 220­240 V Power Pro connector IN (Blue) 11) 3-pin DMX connector OUT 12) 3-pin DMX connector IN 13) 6,3mm jack for remote control 14) 5-pin DMX connector IN 15) Safety Eye

Fig. 03

Product code: 61115

11

Stellar S-1200 Snow Machine

Product Specifications

Model:

Stellar S-1200 Snow Machine

Electrical: Input voltage: Power consumption: Fuse:

220­240 V AC, 50 Hz 1200 W 8A /250 V

Physical: Dimensions: Weight:

503 x 302 x 440 mm (LxWxH) 9,4 kg

Snowmachine capacity: Tank capacity: Fluid consumption: Adjustable output level: Safety:

5 L 480 ml/min @full output 0­100 % Continuous and steady output till tank runs out of liquid

Operation and control: Control: DMX channels: Control panel:

DMX-512, Manual, Remote, Timer 1, 3, 5 channels LCD display and buttons

Connections: Power connections: Data connections: Signal pinouts:
Remote control connection:

Pro power connector (Blue) IN 3-pin + 5-pin DMX connectors IN/OUT 3-pin: pin 1 (ground), pin 2 (-), pin 3 (+) 5-pin: pin 1 (earth), pin 2 (-), pin 3 (+), pin 4 (N/C), pin 5 (N/C) 6,3mm jack

Construction: Housing: Color: IP rating: Cooling:

Metal Dark Gray / Silver IP20 Convection

Thermal: Minimum ambient temperature ta: Maximum ambient temperature ta: Maximum housing temperature tc:

0 °C 40 °C 45 °C

Minimum distance: Minimum distance from flammable surfaces:

0,8 m

3.4. Accessories

The device is delivered without remote control. To use a remote control with the device, it is necessary to purchase the remote control.

Product code: 61115

12

Stellar S-1200 Snow Machine Dimensions

Product code: 61115

13

Fig. 04

Stellar S-1200 Snow Machine
4. Installation and Setup
Safety Instructions for Installation
WARNING Incorrect installation can cause serious injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and site-specific regulations.
Installation Site Requirements
The device can be used only indoors. The device can be mounted to a truss or other rigging structure in any orientation. The minimum distance to other objects must be bigger than 0,8 m. The minimum distance between the snow output nozzle (03) and the flammable surface must be
bigger than 0,8 m. The maximum ambient temperature ta = 40 °C must never be exceeded. The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
Rigging
The device can be positioned on a flat surface or mounted to a truss or other rigging structure in a horizontal orientation. The maximum inclination angle of the device should not exceed 15º. Make sure that all loads are within the pre-determined limits of the supporting structure.
CAUTION Restrict the access under the work area during rigging and/or derigging.

Product code: 61115

14

Stellar S-1200 Snow Machine
To mount the device, follow the steps below:
Use a clamp to attach the device to the supporting structure, as shown in Fig. 05. Make sure that the device cannot move freely. 02) Secure the device with a secondary suspension, for example a safety cable. Make sure that the secondary suspension can hold 10 times the weight of the device. If possible, the secondary suspension should be attached to a supporting structure independent of the primary suspension. Put the safety cable through the safety eye (15), as shown in Fig. 05.

Fig. 05

Product code: 61115

15

Stellar S-1200 Snow Machine
Connecting to Power Supply
DANGER Electric shock caused by short-circuit
The device accepts AC mains power at 220­240 V and 50 Hz. Do not supply power at any other voltage or frequency to the device.
This device falls under IEC protection class I. Make sure that the device is always electrically connected to the ground (earth).
Before connecting the device to the socket-outlet: Make sure that the power supply matches the input voltage specified on the information label on
the device. Make sure that the socket-outlet has ground (earth) connection. Connect the device to the socket-outlet with a power plug. Do not connect the device to a dimmer pack, as this may damage the device.

Product code: 61115

16

Stellar S-1200 Snow Machine
5. Setup
Warnings and Precautions
Attention Connect all data cables before supplying power. Disconnect power supply before connecting or disconnecting data cables.
Stand-alone Setup
When the Stellar S-1200 Snow Machine is not connected to a controller or to other devices, it functions as a stand-alone device. It can be operated manually.
For more information about the control mode, refer to 6.7.4.1. DMX Address on page 29.
DMX Connection
DMX-512 Protocol
You need a DMX serial data link to run snow shows of one or more devices using a DMX-512 controller or to run synchronized shows of two or more devices set in a DMX mode.
The Stellar S-1200 Snow Machine has 3-pin/5-pin DMX signal IN and OUT connectors.
The pin assignment is as follows: 3-pin: pin 1 (ground), pin 2 (-), pin 3 (+) 5-pin: pin 1 (ground), pin 2 (-), pin 3 (+), pin 4 (N/C), pin 5 (N/C)
Devices on a serial data link must be daisy-chained in a single line. The number of devices that you can control on one data link is limited by the combined number of the DMX channels of the connected devices and the 512 channels available in one DMX universe.
To comply with the TIA-485 standard, no more than 32 devices should be connected on one data link. In order to connect more than 32 devices on one data link, you must use a DMX optically isolated splitter/booster, otherwise this may result in deterioration of the DMX signal.
Note: Maximum recommended DMX data link distance: 300 m Maximum recommended number of devices on a DMX data link: 32 devices

Product code: 61115

17

Stellar S-1200 Snow Machine
DMX Cables Shielded twisted-pair cables with 3-pin/5-pin XLR connectors must be used for reliable DMX connection. You can purchase DMX cables directly from your Highlite International dealer or make your own cables. If you use 3-pin XLR audio cables for DMX data transmission, this may lead to signal degradation and unreliable operation of the DMX network. When you make your own DMX cables, make sure that you connect the pins and wires correctly as shown in Fig. 06.
Fig. 06 DMX Linking To connect multiple devices on one DMX data link, follow the steps below: Use a 3-pin/5-pin DMX cable to connect the DMX OUT connector of the lighting controller to the DMX IN connector of the first device. 02) Connect the first device’s DMX OUT connector to the second device’s DMX IN connector with a 3-pin/5-pin DMX cable. 03) Repeat step 2 to connect all devices in a daisy-chain as shown in Fig. 07. 04) Connect a DMX terminator (120 resistor) to the DMX OUT connector of the last device on the data link.

Product code: 61115

18

Stellar S-1200 Snow Machine

Fig. 07
DMX Addressing
In a setup with multiple devices, make sure that you set the DMX starting address of each device correctly. The Stellar S-1200 Snow Machine has 3 personalities: 1 channel, 3 channels, 5 channels.
If you want to connect multiple devices on one data link and use them in 5-channel mode, for example, follow the steps below:
Set the starting address of the 1st device on the data link to 1 (001). 02) Set the starting address of the 2nd device on the data link to 6 (006), as 1 + 5 = 6. 03) Set the starting address of the 3rd device on the data link to 11 (011) as 6 + 5 = 11. 04) Continue assigning the starting addresses of the remaining devices by adding each time 5 to the
previous number.
Make sure that you do not have any overlapping channels in order to control each Stellar S-1200 Snow Machine correctly. If two or more devices are addressed similarly, they will work similarly.

Product code: 61115

19

Stellar S-1200 Snow Machine
6. Operation
Safety Instructions for Operation
Attention This device must be used only for the purposes it is designed for.
This device is designed to be used as a professional snow effect. Any incorrect use may lead to hazardous situations and result in injuries and material damage. This device is not suitable for households. Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Attention Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.
Recommended Snow Fluid
It is recommended to operate the device with the following snow fluids. Other snow liquids may cause poor effect or damage the device. Product code: 80341 ­ Showgear Snow/Foam Fluid 5 L Product code: 80342 ­ Showgear Snow/Foam Fluid 5 L Concentrate

Product code: 61115

20

Stellar S-1200 Snow Machine
Filling the Tank
WARNING Risk of explosion caused by incorrect handling
Do not add flammable liquids such as perfume and alcohol to the snow fluid. Operate the device only with the fluids recommended in this user manual. Make sure that you do not to exceed the maximum fluid level. Do not overfill! To fill the tank, follow the steps below:
Do not disconnect the safety cable. Unscrew the lid on the fluid tank, as shown in Fig. 08. Take out the fluid tank, as shown in Fig. 09.

Fig. 08

Fig. 09

Product code: 61115

21

Stellar S-1200 Snow Machine
Place the fluid tank on a flat surface near the device, as shown in Fig. 10. Use a funnel to pour the snow fluid into the tank, as shown in Fig. 11.

Fig. 10

Fig. 11

Fill the fluid container with the recommended snow fluid ( Max. Fluid Tank Capacity 5 L). Make sure that you do not overfill. Put the fluid tank back in the device, as shown in Fig. 12. Screw the lid back on the fluid tank, as shown in Fig. 13.

Fig. 12

Fig. 13

Notes: Do not allow the snow liquid to become contaminated. Always replace the caps on the snow liquid
container and the snow machine liquid tank immediately after filling.

Product code: 61115

22

Stellar S-1200 Snow Machine
Emptying the Tank after Operation
To empty the tank, follow the steps below: Do not disconnect the safety cable. Unscrew the lid on the fluid tank, as shown in Fig. 14. Take out the fluid tank, as shown in Fig. 15.

Fig. 14

Fig. 15

Place the fluid tank on a flat service near the device, as shown in Fig. 16. Use a funnel to pour the snow fluid from the tank into original snow fluid jerry can, as shown in Fig. 17.

Fig. 16

Fig. 17

Fill the jerry can with the exact snow fluid. Do not mix different types of snow fluid. Make sure that you do not overfill.

Product code: 61115

23

Stellar S-1200 Snow Machine
Put the fluid tank back in the device, as shown in Fig. 18. Screw the lid back on the fluid tank, as shown in Fig. 19.

Fig. 18

Fig. 19

Notes: Do not allow the snow liquid to become contaminated. Always replace the caps on the snow liquid container and the snow machine liquid tank immediately after filling.

Restarting the Device after Running the Tank empty

When running a tank completely empty, the pump will automatically stop blowing snow to prevent damage to the pump. The display will blink and show:

If you refill the tank and try to operate the device, the display will keep displaying this Warning message. Make sure you fill the entire tank and then manually start blowing snow. This will take a few seconds until the completely emptied lines are filled with snow fluid.
Control Modes
The Stellar S-1200 Snow Machine supports the following control modes: Manual (snow intensity/volume, duration, interval/timer) Manual via Remote control 1, 3, 5 DMX channels
For more information about how to connect the devices, refer to 5. Setup on pages 18­20.

Product code: 61115

24

Stellar S-1200 Snow Machine
Manual Operation
To set up the device, follow the steps below: Fill the tank (Fluid Tank Capacity 5 L). See 6.3. Filling the Tank on page 22 for more information. Connect the power cable before supplying power to the device. See 4.5. Connecting to Power Supply on page 17 for more information. Set the ON/OFF switch (09) to ON.
To operate the device manually as a stand-alone device: Adjust the output volume in Snow menu. See 6.7.4.2. Snow Volume on page 27 for more information. Adjust the wind speed in Wind menu. See 6.7.4.3. Wind Speed on page 27 for more information. Adjust the Interval volume in Interval menu. See 6.7.4.3. Interval on page 28 for more information. Adjust the Duration volume in Duration menu. See 6.7.4.4. Duration on page 28 for more information. Notes: Manual operation with the control panel on the device always has priority over the remote control.
Control Panel (Device) A) LCD display B) Start / Pause button C) Down button D) Up button E) Menu button
Fig. 20 Use the START / PAUSE button to start/pause your snow operation. Use the UP and DOWN buttons to increase/decrease numeric values. Use the MENU button to navigate through the menus.

Product code: 61115

25

Stellar S-1200 Snow Machine
Start-up Upon start-up, the display will show the current software version.
When the device is ready, the display will show:
Menu Overview

Notes: Manual operation with the control panel on the device always has priority over the remote control.

Product code: 61115

26

Stellar S-1200 Snow Machine
Main Menu Options The main menu has the following options:

Press the MENU button to navigate through the main menu. DMX Address
In this menu you can set the DMX address.
Press the UP/DOWN buttons to set the desired DMX address. The adjustment range is 001­512. Snow Volume
In this menu you can manually set the output volume.
Press the UP/DOWN buttons to set the desired output volume. The adjustment range is 1­100%. Wind Speed
In this menu you can manually set the wind speed.
Press the UP/DOWN buttons to set the desired wind speed. The adjustment range is 50% or 100%.

Product code: 61115

27

Stellar S-1200 Snow Machine
DMX Mode In this menu you can manually set the DMX mode.
Press the UP/DOWN buttons to set the desired DMX mode. Interval
In this menu you can set the snow interval.
Press the UP/DOWN buttons to set the desired interval time. The adjustment range is 0 or between 20­2000 sec. Duration
In this menu you can set the duration of the snow output.
Press the UP/DOWN buttons to set the desired duration of your snow output. The adjustment range is 10­ 200 sec.
Timer In this menu you can enable/disable the timer.
Press the UP/DOWN buttons to set the timer ON or OFF.

Product code: 61115

28

Stellar S-1200 Snow Machine
Timer Mode
Set the snow output volume. See 6.7.4.2. Snow Volume on page 27 for more information. Set the wind speed. See 6.7.4.3. Wind Speed on page 27 for more information. Set the interval time between separate snow outputs. See 6.7.4.5. Interval on page 28 for more information. Set the snow output duration. See 6.7.4.6. Duration on page 28 for more information. Press the MENU button, until the display shows: MSG STP F100. Set the Timer to ON. See 6.7.4.7. Timer on page 28 for more information. The device starts to blow snow with the parameters set in 6.7.4.2., 6.7.4.3., 6.7.4.5. and 6.7.4.6. When the device is blowing snow, press the UP/DOWN buttons to change the snow volume (1­100), and press START / PAUSE for 2 seconds to change the fan speed (WIND) from 1­100. When you press the START / PAUSE button during the timer function, the display shows STP and the device will stop blowing snow, but the fan will spin another 2­3 seconds. To deactivate the STP function, press the START / PAUSE button. To deactivate the timer function, set the Timer to OFF. See 6.7.4.7. Timer on page 28 for more information.
DMX Control Mode
When you connect a DMX cable to the input of the device, the display shows: MSG:DMX. Press the UP and DOWN buttons to select the DMX starting address of the device. The selection range is 001­512. See 6.7.4.1. DMX Address on page 27 and 5.3.4. DMX Addressing on page 19 for more information. When the device is blowing snow, press the UP/DOWN buttons to change the H (WIND 50%) from 1­ 100, and press START / PAUSE button for 2 seconds to change to F (WIND 100%) and use the UP/DOWN buttons to change the F value from 1­100. When you press the START / PAUSE button during the DMX control mode, the display shows STP and the device will stop blowing snow, but the fan will spin another 2­3 seconds. To deactivate the STP function, press the START / PAUSE button.

Product code: 61115

29

Stellar S-1200 Snow Machine
Manual Mode
Set the snow output volume. See 6.7.4.2. Output Volume on page 27 for more information. Set the wind speed. See 6.7.4.3. Wind Speed on page 27 for more information. Press the MENU button, until the display shows: MSG RUN F100. When the device is blowing snow, press the UP/DOWN buttons to change the H (WIND 50%) from 1­ 100, and press START / PAUSE button for 2 seconds to change to F (WIND 100%) and use the UP/DOWN buttons to change the F value from 1­100. When you press the START / PAUSE button during the manual control mode, the display shows STP and the device will stop blowing snow, but the fan will spin another 2­3 seconds. To deactivate the STP function, press the START / PAUSE button.
DMX Operation
To setup up the device, follow the steps below: Fill the tank (Fluid Tank Capacity 5 L). See 6.3. Filling the Tank on pages 21­23 for more information. Connect the DMX cables before supplying power to the device. See 5.3. DMX Connection on page 17 for more information Connect the power cable before supplying power to the device. See 4.5. Connecting to Power Supply on page 16 for more information. Set the ON/OFF switch (18) to ON. Set the DMX starting address of the device in Address menu. See 5.3.4. DMX Addressing on page 19 and 6.7.4.5. DMX Address on page 30.
Note: Manual operation with the control panel on the device always has priority over the remote control.

Product code: 61115

30

Stellar S-1200 Snow Machine

DMX Channels

1 Channel

1 CH Function 1 Snow Output

Value 000­255

Setting Snow output from 0­100%

3 Channels

3 CH 1 2
3

Function Snow Output Wind
Device ON/OFF

Value
000­255 000­255 000­128 129­255

Setting Snow output from 0­100% Wind speed from 0­100% OFF ON

5 Channels

5 CH 1 2
3
4 5

Function Snow Output Wind
Device ON/OFF
Duration Interval

Value
000­255 000­255 000­128 129­255 000­255 000­255

Setting Snow output from 0­100% Wind speed from 0­100% OFF ON From 0­255 seconds From 0­2550 seconds

Notes:

Interval =0 means the device is constantly blowing snow.

Product code: 61115

31

Stellar S-1200 Snow Machine

7. Troubleshooting

This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts.

Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.

Refer servicing to instructed or skilled persons. Contact your Highlite International dealer in case the solution is not described in the table.

Problem The device does not function at all The device does not respond to DMX control
The device responds erratically to DMX control
No snow output
Snow output nozzle is sputtering Device does not function correctly. (Error message: NO FLUID)

Probable cause(s) No power to the device
Main fuse is blown The controller is not connected The signal is reversed. The 3-pin/5-pin DMX OUT of the controller does not match the DMX IN of the device The controller is defective
Bad data link connection
The data link is not terminated with a 120 termination plug Incorrect addressing In case of a setup with multiple devices, one of the devices is defective and disturbs data transmission on the link Device is too hot
The device is damaged The power supply settings do not match local AC voltage and frequency The fluid pipes or the snow output nozzle (03) are clogged.
Incompatible snow fluid
Incompatible snow fluid
Tank is empty
Fluid pipes are empty

Solution Check if power is switched on and cables
are plugged in Replace the fuse. See 8.3.1. Replacing
the Fuse on page 39 Connect the controller Install a phase-reversing cable between
the controller and the device
Try using another controller Examine connections and cables.
Correct poor connections. Repair or replace damaged cables
Insert a termination plug in the DMX OUT connector of the last device on the link
Check address settings and correct, if necessary
To find out the defective device, bypass one device at a time until normal operation is restored
Allow device to cool down. Make sure that air vents are not blocked.
Disconnect the device and contact your Highlite International dealer
Disconnect the device. Check the settings and correct, if necessary
Clean the fluid pipes. See 8.2.1. Basic Cleaning Instructions and 8.2.2. Cleaning the Fluid Pipes on page 38
Use the recommended snow fluid. See 6.2. Recommended Snow Fluid on page 21
Use the recommended snow fluid. See 6.2. Recommended Snow Fluid on page 21
Fill the tank. See 6.3. Filling the Tank on page 22
Restart the device. See 6.5. Restarting the Device after Running the Tank empty on page 26

Product code: 61115

32

Stellar S-1200 Snow Machine
8. Maintenance
Safety Instructions for Maintenance
DANGER Electric shock caused by dangerous voltage inside
Disconnect power supply before servicing or cleaning.
WARNING Risk of burns due to hot surface
Allow the device to cool down for at least 15 minutes before servicing or cleaning.
Preventive Maintenance
Attention Before each use, examine the device visually for any defects.
Make sure that: All screws used for installing the device or parts of the device are tightly fastened and are not
corroded. The safety devices are not damaged. There are no deformations on housings, fixations and installation points. The power cables are not damaged and do not show any material fatigue.
Basic Cleaning Instructions The device must be cleaned periodically from the built-up dust and snow fluid residues. To clean the device, follow the steps below:
Disconnect the device from the electrical power supply. Allow the device to cool down for at least 1 hour. Remove the dust collected on the external surface with dry compressed air and a soft brush. Clean the snow fluid residues from the snow output nozzle (03) with a damp cloth. Use only a clean, lint-free soft cloth. Clean the DMX and other connections with a damp cloth.
Attention
Do not immerse the device in liquid. Do not use alcohol or solvents. Make sure that the connections are fully dry before connecting the device to the power supply and
to other devices.

Product code: 61115

33

Stellar S-1200 Snow Machine
Cleaning the Fluid Pipes
The device must be cleaned periodically from the snow fluid residues. After every 40 hours of continuous operation, it is recommended to run a cleaning solution composed of 80 % distilled water and 20 % white vinegar through the system.
To clean the device, follow the steps below:
Disconnect the device from the electrical power supply. Allow the device to cool down for at least 1 hour. Clean out debris with vinegar and a pipe cleaner, making sure that the snow output nozzle (03) is free of clogs. Remove all snow liquid from the tank. See 6.4. Emptying the Tank after operation on page 24 for more information. Add a cleaning solution to tank. Connect the power cable before supplying power to the device. See 4.5. Connecting to Power Supply on page 17 for more information. Make sure that you run the device until tank is empty. Make sure that you use the device in spaces that have good airflow. Repeat this 2-4 times. Refill with snow liquid.
Corrective Maintenance
The device does not contain user-serviceable parts. Do not open the device and do not modify the device.
Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for more information.
Replacing the Fuse
DANGER Electric shock caused by short-circuit
Do not bypass the thermostatic switch or fuses. For replacement use fuses of the same type and rating only.
Power surges, short-circuit or incorrect electrical power supply may cause a fuse to burn out. If the fuse burns out, the device will not function anymore. If this happens, follow the steps below.
Disconnect the device from the electrical power supply. 02) Allow the device to cool down for at least 15 minutes. 03) Loosen the fuse cover with a screwdriver and remove the fuse holder. 04) If the fuse is brown or unclear, it is burned out. Remove the old fuse. 05) Insert a new fuse in the fuse holder. Make sure that the type and the rating of the replacement fuse
are the same as the ones specified on the information label of the product. 06) Replace the fuse holder in the opening and tighten the fuse cover.

Product code: 61115

34

Stellar S-1200 Snow Machine
9. Deinstallation, Transportation and Storage
Instructions for Deinstallation
WARNING Incorrect deinstallation can cause serious injuries and damage of property.
Let the device cool down before dismounting. Disconnect power supply before deinstallation. Always observe the national and site-specific regulations during deinstallation and derigging of the
device. Wear personal protective equipment in compliance with the national and site-specific regulations.
Instructions for Transportation
Make sure that the liquid tank is empty before transportation. Use the original packaging to transport the device, if possible. Always observe the handling instructions printed on the outer carton box, for example: “Handle with
care”, “This side up”, “Fragile”.
Storage
Make sure that the liquid tank is empty before storing the device. See 6.4. Emptying the Tank after operation on page 24 for more information.
Clean the device before storing. Follow the cleaning instructions in chapter 8.2.1. Basic Cleaning Instructions on page 38, and 8.2.2. Cleaning the Fluid Pipes.
Store the device in the original packaging, if possible
10. Disposal
Correct disposal of this product
Waste Electrical and Electronic Equipment
This symbol on the product, its packaging or documents indicates that the product shall not be treated as household waste. Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. For more detailed information about recycling of this product contact the local authorities or the authorized dealer.
11. Approval

Check the respective product page on the website of Highlite International (www.highlite.com) for an available declaration of conformity.

Product code: 61115

35

Stellar S-1200 Snow Machine

Product code: 61115

36

Stellar S-1200 Snow Machine

Product code: 61115

37

Stellar S-1200 Snow Machine

Product code: 61115

38

©2023 Showtec

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals