Showtec EventLITE 4 Battery LED Spotlights User Manual

June 13, 2024
Showtec

Showtec logo User MANUAL
EventLiTE 4/8 Mini Q4 Vi

Product code: 44080

EventLITE 4 Battery LED Spotlights

Showtec EventLITE 4 Battery LED Spotlights

Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
EventLITE 4/8 Mini Q4
Preface
Thank you for purchasing this Snhowtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
This user manual contains information concerning:

  • Safety instructions
  • Installation and operation of the device
  • Intended and non-intended use of the device
  • Maintenance procedures
  • Troubleshooting
  • Transport, storage and disposal of the device
    Non-observance of the instructions in this user manual may result in serious injuries and damage of property.

©2023 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or other language versions, please visit our website www.highlite.com or contact us at service@highlite.com.
Highlite International and its authorized service providers are not liable for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or reliance on the information contained in this document.

Introduction

1.1. Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer.
Your shipment includes:

  • Showtec EventLiTE 4/8 Mini Q4
  • AC Power Adapter (1,1 m)
  • IR Remote control
  • User manual

Showtec EventLITE 4 Battery LED Spotlights - Fig

1.2. Intended Use
This device is intended for professional use as a professional outdoor spot. It is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
1.3. Product Lifespan
This device is not designed for permanent operation. Disconnect the device from the electrical power supply when the device is not in operation. This will reduce the wear and will improve the device’s lifespan.
1.4, LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate ventilation and operating the LEDs at the lowest possible brightness.
1.5. Text Conventions
Throughout the user manual the following text conventions are used:

Buttons:|  All buttons are in bold lettering, for example “Press the UP/DOWN buttons”
---|---
References:| References to chapters and parts of the device are in bold lettering, for example:“Refer to 2. Safety”, “turn the adjustment handle (05)””
0255:|  Defines a range of values
Notes:| Note: (in bold lettering) is followed by useful information or tips

1.6. Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER   Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION   Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
Attention   Indicates important information for the correct operation and use of the product.
Important Read and observe the instructions in this document.
Electrical hazard
Eye damage hazard
Provides important information about the disposal of this product.
1.7. Symbols on the Information Label
This product is provided with an information label. The information label is located on the mounting bracket of the device.
The information label contains the following symbols:
This device shall not be treated as household waste.
This device is rated IP65.
This device falls under IEC protection class |.
Read the user manual supplied with the device.

Safety

Important
Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
2.1. Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.

  • Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within children’s reach. Packaging material is a potential source of danger for children.

DANGER
Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage may be present.

  • Donot open the device or remove any covers.

  • Donot operate the device if the covers or the housing are open. Before operation, check if the housing is firmly closed and all screws are tightly fastened.

  • Disconnect the device from electrical power supply before service and maintenance, and when the device is not in use.
    DANGER
    Electric shock caused by short-circutt
    This device falls under IEC protection class I.

  • Make sure that the device is electrically connected to ground (earth). Connect the device only toa socket-outlet with ground {earth) connection.

  • Donot cover the ground (earth) connection.

  • Donot bypass the thermostatic switch or fuses.

  • Donotlet the power cable come into contact with other cables. Handle the power cable and all connections with the mains with caution.

  • Donot modify, bend, mechanically strain, put pressure on, pull or heat up the power cable.

  • Make sure that the power cable is not crimped or damaged. Examine the power cable periodically for any defects.

  • Donotimmerse the device in water or other liquids. Do not install the device in a location where flooding may occur.

  • Donotuse the device during thunderstorms. Disconnect the device from the electrical power supply immediately.

  • Keep the connectors sealed with the rubber caps when the connectors are not in use.

  • Donot connect the cables from above the connectors, if the device is installed outdoors. Make a ‘drip loop’ in the cable so that rain water cannot enter the device.

WARNING
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights.
CAUTION
Possible eye damage caused by high light intensity
Possibly hazardous optical radiation emitted from this device.

  • Donotlook at the operating light source. May be harmful to the eye.

  • Donotlook at the light source with optical instruments that may concentrate the light output.

  • Make sure that persons are not looking directly into the light source when the device lights up suddenly. This can happen when the device is powered or when it receives DMX signal, or when certain menu items are selected.

  • Disconnect power supply before servicing.

  • Wear protective goggles if looking into light source during service or maintenance.
    Attention
    Power supply

  • Before connecting the device to the power supply. make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.

  • Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the required power consumption of the device.
    Attention
    General safety

  • Donot connect the device to a dimmer pack.

  • Donot switch the device on and off in short intervals. This decreases the device’s life.

  • Donot shake the device. Avoid brute force when installing or operating the device.

  • Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for more information, as servicing can be performed only by instructed or skilled persons.

  • If the device is dropped or struck, disconnect the device from the electrical power supply immediately.

  • If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it on immediately. Let the device reach room temperature before switching it on, otherwise it may bedamaged by the formed condensation.

  • If the device fails to work property. discontinue the use immediately.
    Attention
    For professional use only
    This device shall be used only for the purposes it {s designed for.

This device is designed to be used as a professional outdoor spot. Any incorrect use may lead to hazardous situations and result in injuries and material damage.

  • This device is not suitable for households and for general lighting.

  • This device is not designed for permanent operation.

  • This device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.
    Attention
    Before each use, examine the device visually for any defects.
    Make sure that:

  • All screws used for installing the device or parts of the device are tightly fastened and are not corroded.

  • The safety devices are not damaged.

  • There are no deformations on housings, fixations and installation points.

  •  The lens is not cracked or damaged.

  • The power cables are not damaged and do not show any material fatigue.
    Attention
    Do not expose the device to condiifons that exceed the rated IP class condiitons.

This device is IP65 rated. IP (Ingress Protection) 65 class means that the device is dust-tight and protected against harmful effect of water jets.
2.2, Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons. Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite International dealer for more information.
instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled person, for specific tasks and work activities associated with the installation, service and maintenance of this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards associated with the instatlation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons include not only users of the product but also any other persons that may have access to the device or who may be in the vicinity of the device.

Description of the Device

The Showtec EventLiTE 4/8 Mini is a battery-powered RGBW spot in a sturdy, IP65-rated aluminium housing. The battery will last up to 11 hours on a single colour when it is fully charged. The EventLiTE 4/8 includes several presets and sound-activated programs, and can be controlled through the display and buttons on the back or by the included !R-remote controller.
3.1. Front View

Showtec EventLITE 4 Battery LED Spotlights - Showtec EventLITE 4 Battery LED
Spotlights

  1. Mounting bracket

  2. 2x adjustment screw

  3. 4×8 W 4in-1 RGBW LEDs

  4. Infrared sensor
    3.2. Back ViewShowtec EventLITE 4 Battery LED Spotlights -fig
1****

  5. DC connector,

  6. V DC LCD display + control buttons

  7. ON / OFF button

  8. Protective valve

3.3. Product Specifications

Model: EventLITE 4/8 Mini Q4

AC power adapter:
Input voltage:| 100–240 V AC, 50/60 Hz
Input current:| 0,6 A
Output voltage:| 12 V DC
Output current:| 1,4 A
Physical:
Dimensions:| 149 x 103 x 138 mm (L x W x H)
Weight:| 1 kg
Optics:
Light source:| 4 x 8 W RGBW LEDs
Total luminous flux:| 380 lm
Red:| 77 lm
Green:| 169 lm
Blue:| 36 lm
White:| 154 lm
Illuminance @2m:| 618 lx
Illuminance @3m:| 275 lx
Illuminance @5m:| 100 lx
CRI:| 76
CCT:| 13960 K
Dimmer:| 0–100 %
Strobe:| 0–20 Hz
Beam Angle Circular:| 20°
Refresh rate:| 3000 Hz
Operation and control:
Control:| Manual, Auto, Built-in programs, IR Remote
Control panel:| 7-segment LCD display and menu buttons
Battery:
Battery type:| Lithium-ion
Battery voltage:| 12,6 V
Capacity:| 2,6 Ah
Runtime (full output):| 4 h
Runtime (average):| 11 h
Charging time:| 5 h
Construction:
Housing:| Die-cast aluminum
Color:| Black
IP rating:| IP65
Cooling:| Convection
Thermal:
Minimum ambient temperature:| -5 °C
Maximum ambient temperature ta:| 45 °C
Maximum housing temperature tc:| 70 °C
Minimum distance:
Minimum distance from flammable surfaces:| 1 m
Minimum distance to lighted object:| 0,5 m

3.4 Dimension

Showtec EventLITE 4 Battery LED Spotlights - Fig 4

Installation

4.1, Safety Instructions for Installation
WARNING
incorrect Installation can cause serious Injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
4.2, Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and site-specific regulations.
4.3. Installation Site Requirements

  • The device can be used outdoors.
  • The device can be mounted to a truss or other rigging structure.
  • The minimum distance between the light output and the illuminated surface must be bigger than 0.5m.
  • The maximum ambient temperature to = 45 °C must never be exceeded.
  • The relative humidity must not exceed 50 % with an ambient temperature of 45 °C.

4.4.1. Rigging
The device can be positioned on a flat surface (see Fig. 06) or mounted to a truss or other rigging structure in any orientation. Make sure that all loads are within the pre-determined limits of the supporting structure.
CAUTION
Restrict the access under the work area during rigging and/or derigging.
To mount the device. follow the steps below:

  1. Use a clamp to attach the device to the supporting structure, as shown in Fig. 05. Make sure that the device cannot move freely.
  2. Secure the device with a secondary suspension, for example a safety cable. Make sure that the secondary suspension can hold 10 times the weight of the device. If possible, the secondary suspension should be attached to a supporting structure independent of the primary suspension. Put the safety cable through the mounting bracket (01). as shown in Fig. 05.

Showtec EventLITE 4 Battery LED Spotlights - Fig 5

44.1, Angle Adjusiment
You can adjust the angle of the device with the 2 adjustment screws (02).

  1. Turn the adjusiment screws (02) counterclockwise to release it.
  2. Tit the device at the desired angle (see Fig. 06).
  3. Turn the adjusiment screws (02) clockwise to tighten it. Make sure that the device cannot move freely after the adjustment screws (02) is tightened.Showtec EventLITE 4 Battery LED Spotlights - Fig 6

4.5. Charging the Battery
DANGER
Risk of explosion caused by incorrect handling
This device contains a built-in rechargeable lithium-ion battery. The battery is not replaceable. The battery may explode or cause burns if it is crushed. disassembled or exposed to fire or high temperatures.

  • Donot open the device and do not attempt to remove the built-in battery. This device is delivered with an AC power adapter that is used to charge the battery. Before connecting the AC power adapter to the socket-outiet, make sure that the power supply matches the input vaitage specified on the information label on the AC power adapter.
    To charge the battery follow the steps bellow:
  1. Put the device indoors to charge. Connect the AC power adopter to the device. Use only the AC power adopter delivered with the device.
    02)Connect the AC power adapter to the socket-outlet.
    During charging. a € on the display is blinking. When charging is completed. the display shows:
  • Charge the battery before using the device for the first time.
  • Do not deep discharge the battery as this will shorten the battery’s lifetime. Recharge the battery as early as possible. Do not let the light run until the battery is depleted.
  • Make sure that the battery is charged to at least 50 % before storing the device.
    It is recommended fo charge the device at an ambient temperature between 0 °C and 35°C.
    If the device is charged in a carying case, leave the case open.
    Refer to 3.3. Product SpecMcalions on page 11 for the charge time of the battery.

Setup

5.1 Warnings and Precautions
DANGER
Electric shock caused by short-ckrcull
This device is P65 rated.

  • Donot expose the device to conditions thet exceed the rated IP class conditions.
  • Keep the connector sealed with the rubber cap when the connector is not in use.
    5.2. Stand-alone Setup
    The EventLiTE 4/8 Mini Q4 functions as a stand-alone device.
    For more information about the control modes, refer to 6.2. Control Modes on page 17.

Operation

6.1. Safety Instructions for Operation
Attention
This device must be used only for the purposes It Is designed for.
This device is intended for professional use as an outdoor spot. It is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Attention
Power supply
Before connecting the device to the power supply. make sure that the current, voltage and frequency match the input voltage. current and frequency specified on the information label on the device.
6.2, Control Modes
The EventLiTE 4/8 Mini @4 can be operated as a stand-alone device.
The EventLiTE 4/8 Mini @4 supports the following control modes:

  • Stand-alone: Auto, Built-in programs, Preset colors, Manual and Sound-controlled
    To run the built-in programs:
    01} Run all built-in programs in a sequence in Auto menu. See 6.6.1. Aute on page 20 for more information.
  1. Select one of the 16 built-in programs in Program menu. See 6.6.2. Built- in Programs on page 20 for more information. Adjust the program speed and strobe frequency.
    To run the preset colors:
    Select one of the 39 preset colors in Program menu. See 6.6.2.1. Program 01 on page 20 for more information.
    To operate the device manually as a stand-alone device:
  •  Adjust the colors in Static color control. See 6.6.3. Statte color control on page 21 for more information.
    For more information about sound-controlled operation mode see 6.6.4. Sound- controlled mode on page 21.

6.3. Control Panel

Showtec EventLITE 4 Battery LED Spotlights - Fig 7
A) LCD display
B) MODE button
C) SET button
D) UP button
E) DOWN button

  • Use the MODE button to exit the current submenu and to return to the Main Menu.
  • Use the UP/DOWN buttons to navigate through the menus or to increase/decrease numeric values.
  • Use the SET button to open the desired menu, to confirm your choice or to set the currently selected value.

6.4. Start-up
Upon start-up the display briefly shows its software version.
Note: if no button is pressed after 30 seconds of inactivity, the display will turn off. Press any button to turn the display on.

6.5 menu Overview

Showtec EventLITE 4 Battery LED Spotlights - Fig 8

6.6. Main Menu Options
Upon start-up, the display shows the current software version.

The main menu has the following options:|
---|---
Auto program mode|
Built-in programs|
Static color control|
Sound-controlled mode|
Settings|
Info|

  •  Press the MODE or UP/DOWN buttons to navigate through the main menu.
  • Press the SET button to open the menus.

6.6.1. Auto Mode
In this menu you can set the Auto mode.
While in the main menu, press the MODE button to select . The device immediately starts the Auto mode.
6.6.2. Bullt-In Programs
In this menu you can set the Built-in programs.

  1. While in the main menu, press the MODE button to select .
  2. Press the SET button to open the menu.
  3. Press the UP/DOWN buttons to select one of the following 2 options:

6.6.2.1. Program 01

  1. If you select program 01, press the SET button to open the submenu and select one of the 2 options:
  2. If you select COO1, press the UP/DOWN buttons to select one of the 39 color macros. C000 is blackout
  3. If you select FSOO, press the UP/DOWN buttons to set the strobe frequency. The adjustment range is between 00-99, from OFF to high frequency.

6.6.2.2. Programs 02-16

  1. If you select one of the programs 02-16, press the SET button to select one of the 2 options:
  2. If you select SPEED, press the UP/DOWN buttons to set the built-in program’s speed. The adjustment range is 01-100, from slow to fast.
  3. If you select STROBE, press the UP/DOWN buttons to set the strobe frequency. The adjustment range is 00-99, from OFF to high frequency.

6.6.3. Static color control
In this menu you can manually set the desired colors.

  1. While in the main menu, press the MODE button to select
  2. Press the SET button to enter the menu.
  3. Press the SET button to select one of the following 4 options:
  4. Press the UP/DOWN buttons to change the values. You can combine Red, Green, Blue and White to  create an infinite range of colors (0-100).
    Gradual adjustment red (0-100)
    Gradual adjustment green (0-100)
    Gradual adjustment blue (0-100)
    Gradual adjustment white (0-1005}

6.6.4. Sound-controlled mode
In this menu you can set the sensitivity of the sound mode.

  1. While in the main menu, press the MODE button to select .
  2. Press the SET button to enter the menu.
  3. Press the UP/DOWN buttons to set the sound sensitivity. The adjustment range is between 0-31.

6.6.5. Settings
In this menu you can restore the default factory settings.

  1. While in the main menu, press the MODE button to select .
  2. Press the SET button to enter the menu.
  3. The display shows the following option:
  4. Press the SET button to reset the device.

6.6.6. Info
In this menu you can view the battery level, the temperature and the current software version.

  1. While in the main menu, press the MODE button to select

  2. Press the SET button to enter the menu.

  3. Press the UP/DOWN buttons to select the following 3 options:
    Battery level
    Temperature
    Software version

  4. Press the SET button to open the submenu and view the additional information.

6.7. Remote Control
The device can be controlled with the included !R remote control.
DANGER
Do not Ingest battery, chemical burn hazard
The remote control contains a coin cell battery. If the coin cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
The battery is already installed in the remote control. It is protected against discharge by a transparent plastic foil. Remove the plastic foil before using the remote control for the first time.
When replacing the battery, make sure that the polarity is correct. Incorrect polarity may damage the remote control.
You can control several devices at the same time with the remote control. Make sure that you point the remote control to the Infrared sensor (04) of the device or group of devices that you want to control, as shown in Fig. 08. If you point the remote control to the infrared sensor (04) of the device outside of the range of the sensor, the device will not respond to the remote control (Fig. 09).Showtec EventLITE 4 Battery LED Spotlights - Fig
9

To operate the device with the IR remote control, point the remote control to the infrared sensor (04).
Note:
The remote control will work only if the device is already operating in Auto, Built-in Programs, Sound or Manual mode.
The remote control has the following functions:
Showtec EventLITE 4 Battery LED Spotlights - Fig1
fig : 10

Note:
When you turn off the device, the next time you tur it on, it will continue to operate in the previously selected operation mode.

Button Function Description
On/Off On/Off Turns the LEDs on/off
Auto Activates Auto mode
Program Activates Built-in Programs mode
Sound-controlled Mode Activates Sound-controlled mode
Speed Activates program speed adjustment
Strobe Activates strobe frequency adjustment
Dimming Activates Manual mode
Plus Increase value
Minus Decrease value
R Red Activates Red LEDs
--- --- ---
G Green Activates Green LEDs
B Blue Activates Blue LEDs
A Amber Activates a mixed color to mimic Amber LEDs
W White Activates White LEDs
0 Cyan Activates cyan color
1 Purple Activates purple color
2 Purple/pink Activates purple/pink color
3 Orange Activates oranae color
4 Cool white Activates cool white color
5 Pink Activates pink color
6 Light green Activates light green color
7 Light blue Activates light blue color
8 Yellow Activates yellow color
9 Warm white Activates warm white color

6.7.1. Auto mode
Press the button to activate Auto mode. The device runs its built-in programs in a sequence.
6.7.2. Built-in Programs

  1. Press the button to activate the Built-in Programs mode.
  2. Press the and buttons to select one of the 16 built-in programs.

6.7.2.1. Sound-controlled mode

  1. Press the button to activate the Sound-controlled mode.
  2. With the and buttons you can set the sensitivity between 00-31.

6.7,2,2, Program Speed

Ol) Press the button to set the program speed.

  1. Press the and buttons to increase/decrease the program speed. The adjustment range is 1-100, from slow to fast.

Note:

If you select program 1 and start adjusting the program speed, the device automatically switches to program 2. It is because the program speed function is available only in programs 2-16. The device searches for and activates the first following program that has the program speed function.
6.7.2.3. Strobe

  1. Press the button to set the strobe frequency.
  2. Press the and  buttons to increase/decrease the strobe frequency. The adjustment range is 0- 99, from OFF to high strobe frequency.

6.7.3. Manual

  1. Press the button to activate Manual mode.
  2. Press the button to select one of the RGBW colors.
  3. Press the and buttons to set the LED brightness of the selected color. The adjustment range is 0-255. You can combine Red, Green, Blue and White to create an infinite range of colors.

6.7.3.1, Color Presets

  1. Press the  buttons to select the color presets.
  2. Press the and buttons to select one of the 39 color presets.

Troubleshooting

This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts.
Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.
Refer servicing to instructed or skilled persons. Contact your Highlite International dealer in case the solution is not described in the table.

Problem Probable cause(s) Solution
The device does not function at all No power to the device •Check if power

is switched on and cables are plugged in
Internal fuse is blown| •Disconnect the device and contact
your Highlite International dealer
The device does not respond to the| The remote control is outside of the range of the sensor of the infrared port| •Walk closer to the device or change the angle at which you point the remote control to the device. See 6.7.
Remote Control on page 23
remote control| The battery of the remote control is depleted| •Change the battery of the remote control
No light or LEDs cut out intermittently| LEDs are damaged| •Disconnect the device and contact
your Highlite International dealer
The power supply settings do not match local AC voltage and frequency| •Disconnect the device. Check the settings and correct, if necessary

Maintenance

8.1. Safety Instructions for Maintenance
DANGER
Blectric shock caused by dangerous voltage Inside
Disconnect power supply before servicing or cleaning.
8.2. Preventive Maintenance
Attention
Before each use, examine the device visually for any defects.
Make sure that:

  • Alscrews used for installing the device or parts of the device are tightty fastened and are not corroded.
  • The safety devices are not damaged.
  • There are no deformations on housings. fixations and installation points.
  • The lens is not cracked or damaged.
  • The power cables are not damaged and do not show any material fatigue.

8.2.1. Basic Cleaning instructions
The external lens of the device must be cleaned periodically in order to optimize the light output. The cleaning schedule depends on the conditions at the site where the device is installed. When smoke or fog machines are used at the site, the device will need more frequent cleaning. On the other hand, if the device is instafed in well-ventilated area, it wil need less frequent cleaning. To establish a cleaning schedule, examine the device at regular intervals during the first 100 hours of operation.
To clean the device, follow the steps below:

  • Disconnect the device from the electrical power supply.
  • Afow the device to cool down for at Jeast 15 minutes.
  • Remove the dust collected on the extemal surface with dry compressed air and a soft brush.
  • Clean the lens with a damp cloth. Use a mild detergent solution.
  • Dry the lens carefully with a lint-free cloth.
  • Clean the DMX and other connections with a damp cloth.

Altention

  • Donot immerse the device in bquid.
  • Donot use alcohol or solvents.
  • Make sure that the connections are fully dry before connecting the device to the power supply and to other devices.

8.2.2, Draining Condensation Water
The EventLiTE 4/8 Mini @4 is IP65 rated. Tne device can resist water jets. If the device is exposed to extreme humid conditions during servicing, condensation may collect inside the device. This can happen also during transportation. if the device is exposed to extreme temperature variations.
if condensation water collects inside the device. follow the steps bellow to remove the condensation water:

  1. Carefully remove the protective valve (08) with a wrench (16 mm).

  2. Let the device operate at full output for 60 minutes.

  3. Let the device cool down for 30 minutes.
    Showtec EventLITE 4 Battery LED Spotlights - Fig11 fig. 11

  4. Install the protective vatve (08) back in place. Make sure that you do not overtighten it.

8.3. Corrective Maintenance
The device does not contain user-serviceable parts. Do not open the device and do not modify the device.
Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for more information.

Deinstallation, Transportation and Storage

9.1. Instructions for Deinstallation
WARNING
incorrect deinstaliation can cause serious Injurles and damage of property.

  • Let the device cool down before dismounting.
  • Disconnect power supply before deinstallation.
  • Always observe the national and site-specific regulations during deinstallation and derigging of the device.
  • Wear personal protective equipment in compliance with the national and site-specific regulations.

9.2. Instructions for Transportation

  • Use the original packaging to transport the device. if possible.
  • Always observe the handling instructions printed on the outer carton box, for example: “Handle with care™, “This side up”, “Fragile”.

9.3. Storage

  • Clean the device before storing. Follow the cleaning instructions in chapter 8.2.1. Baste Cleaning Instructions on page 28.
  • Store the device in the original packaging. if possible.

Disposal

Correct disposal of this product
Waste Electrical and Electronic Equipment
This symbol on the product. its packaging or documents indicates that the product shall not be treated as household waste. Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. For more detailed information about recycling of this product contact the local authorities or the authorized dealer.

Approval

Check the respective product page on the website of Highlite International (www.highlite.com) for an available declaration of conformity.Showtec logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals