BLAUPUNKT Raleigh 910 Multimedia Player Instruction Manual

BLAUPUNKT Raleigh 910 Multimedia Player

Operating instructions

1. Microphone input
2. Reset button
3. Power on/off, or mute
4. Return to main screen
5. Activate voice control
6. Volume+
7. Volume

SAFETY INFORMATION

Use This Product Safely
This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit protect you if you observe the following procedures for installation, use and servicing. This unit doesn’t contain any parts that can be repaired by the user.

When Driving
Keep the volume level low enough to be aware of road and traffic conditions.

When Car Washing
Do not expose the product to water or excessive moisture. This could cause electrical shorts, fire or other damage.

When Parked

• Parking in direct sunlight can produce very high temperatures inside your vehicle.
• Give the interior a chance to cool down before starting playback.

Use the Proper Power Supply
This product is designed to operate with a 12 volt DC Use Authorized Service Centers Do not attempt to disassemble or adjust this precision product. Please refer to the Service Center list included with this product for service assistance.

For Installation
The unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°.

Notes

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

• Before finally installing the unit, connect the wiring temporarily and make sure

• it is all connected up properly and the unit and the system work properly.

• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is an emergency stop.

• If installation angel exceeds 30°from horizontal, the unit might not give its optimum performance.

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

INSTALLATION

DIN FRONT/REAR-MOUNT
This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

Installation Opening

This unit can be installed in any dashboard having an opening as shown below:

ATTENTIONS OF INSTALLATION

1. This player should be installed by professional technician.
2. please read the instruction and operation of equipment carefully before installing.
3. Make sure to connect other wires before power connection.
4. To avoid short circuit. Please make sure all the exposed wire are insulating.
5. Please fix all the wires after installation.
6. Please make connection to the player accordingly to this instruction manual. Wrong connection may cause damage.
7. This player only fit for 12V DC device and please make sure your car belongs to this kind of cathode grounding electrical system.
8. Please connect the wires rightly. Wrong connection will cause malfunction or damage the electrical system.

Note
After the installation is complete, you need to set the language and radio area for the first startup

At first, the user can touch to select the desired language, and then enter the interface for selecting the radio region. After touching the desired radio region, the user can touch the to complete the initial setting.

WIRING CONNECTON

Attention

1. Please make sure “Battery +”and “ACC’ pin location are correct before making connection
2. Parking “wire must be connected to “ground” in order to active the video function
3. This player can only be used by the 12V DC cathode grounding electrical system.
4. Don’t connect the terminals of the car battery until the player is absolutely with well erection joint.
5. Please make sure to connect the yellow wire to the positive of the battery(+).
6. When change the fuse. Please make sure the specifications are same.
7. Using good quality speaker with 4-8 ohm can result in the best effect of the equipment.
8. Connect iPhone to product via USB1 port, User can also go to Apple CarPlay. or connect Android Auto compatible phone to product via USBl port.

Main screen

Touch to enter device menu, the following menu appears

• Touch 11 to show between the driver name and the driver address
• Touch to connect CarPlay.
• Touch to connect Bluetooth.
• Touch to delete the device.
• Touch to Search devices.
• Touch to exit device menu.
• Touch icon to enter home menu.

Home menu

• Android Auto: Connect to Android phone
• Radio : Listen to FM or AM radio program
• Phone : Make a hands-free phone call
• USB : Play music/video/image in USB device
• Apple Car Play: Connect to iPhone
• BT Music : Play audio streaming through Bluetooth
• Camera 1 : View left or right camera
• Camera 2: View left or right camera
• AV-IN : External audio/video players
• Settings : Set the parameters of the product

OPERATION

Radio mode
In the main menu, press the [Radio] icon. The radio page menu is displayed.

Select FM/ AM band

Up to 30 stations can be stored under the FM band and AM band.
Touch the to change FMl /FM2/FM3/AM1 /AM2 band.

Tuning into a station
Tuning into stations manuallY, Long press the or to search previous or next by step.

Station seek tuning
Touch the or to to search for the previous or next available radio station. If the station is searched, the process will stop and play the station searched .

Storing stations manually

• Touch to select FM1/FM2/FM3/AM1/AM2 band .
• Received the desired station .
• Press one of the memory buttons [1 ]-[6] for approx. 2 seconds to store the current station at the button. The station is stored.

Automatic Search and Storage Station

• Long press l to automatic search and save station; When search is completed, the first radio station searched will be automatically played and the stations will stored in the preset [ 1 ] ~FM3(or AM 1 / AM2).

Scanning stations Fial
Touch the to listen the preset stations [1] to [6] FM1 ~FM3(or AM 1 / AM2) for few seconds.

Directly enter frequency
Press button then input desired station frequency and press [ OK ] button.

Adjusting the seek tuning sensitivity

• The seek tuning sensitivity decides whether the automatic station seek tuning finds only strstations or also weaker stations that may be noisy .
• Touch to adjust the sensitivity of station seek tuning.
• If LOC is displayed, only stations with a strong signal are found during seek tuning.
• If DX is displayed, stations with a strong and weak signal are found during seek tuning.

RDS function
Many FM stations broadcast an RDS (Radio Data System} signal in addition to their programmed in the Europe reception area that allows additional functions, such as the display of the station name.

Switching AF(Alternate frequencies) function on/off

• If the AF function is activated, the car audio system automatically tunes into the best receivable frequency for the station that is currently set
• Press [AF] button to switch the AF function on/off.
• If the AF function is switched on, AF is displayed.

Switching the TA (Travel Announcement) function on/off

• If the TA function is activated, the car audio system automatically receive travel announcement.
•  Press [ TA ] button to switch the TA function on/off.

If the TA function is switched on, TA is displayed.

Selecting the program type and starting seek tuning
You can select a program type with the PTY function to search for stations of a particular genre, the following PTY List.

USB media player
Insert USB Flash Drive with media files.

Supporting Format

• ♦ Music : MP3, WMA, FLA(, WAV.
• ♦ Video : MP4, WMV, MKV, AVI, MPEG.
• ♦ Picture : JPG, PNG, BMP.

Connecting a USB data carrier

• Insert the data carrier to the USB2 socket.
• The device automatically switches to USB mode. The data is read, and playback starts with the first media file recognized by the device.

Play Music

• Touch , Display the folder/file list.

• Touch►► to play the next track.

• Touch◄◄to play the previous track.

• Touch  or ► to pause current playing track or replay the paused track.

•  Repeat All files.

• Repeat the same files.

• Repeat all files of current folder.

• Playback in random.

•  Display equalizer.

• Input desired track

 Return to the player interface.
Drag the  for fixed-point playback.

Video playback from USB

• Touch   ,select to play.
• for fixed-point to show the video list then select the video track
• Touch the screen to enter full screen mode. If current state is full screen mode, touch the screen again to exit full screen mode.

Image playback from USB

• Touch select to show the picture list then select the picture to play.
• Touch  to rotate current playing pictures.
• Touch   to zoom in or zoom out current playing pictures.
• Touch the screen to enter full screen mode. If current state is full screen mode, touch the screen again to exit full screen mode.

Bluetooth mode

• The Bluetooth connection is not available when Apple CarPlay is on.
• The Bluetooth® function allows pairing cell phones & BT equipped media playback devices with the car audio system.
• Once you pair a cell phone with the car audio system, you can make phone calls
• with the built-in hands free function. You can access the list of dialed numbers and the phone book of the registered cell phone after selecting “Sync” option.
• If the connected Bluetooth® device supports the functions like A2DP and AVRCP, you can play music via the car audio system and control playback. During a call, music playback is interrupted and resumes again after the call.
• If a cell phone is paired via Bluetooth® and a call is received during playback, the source playback is interrupted and the call menu is displayed.

Bluetooth pairing

Select the Bluetooth item and search the Bluetooth device on your phone. Select “Raleigh 91 O” and confirm that this code is shown on “Raleigh 91 O”. Do not enter this code on any accessory. The BT icon will be displayed when successful paired.

Connection status
If a mobile phone/device is connected with the car audio system, the Bluetooth® icon is displayed at the top right corner of the display in all audio/video sources.

Bluetooth PHONE mode
Select In the main menu, press [Phone], the following menu appears.

1. Touch to select the digital numbers on the dial keyboard, touch the  to make a phone call.
2. Touch to enter contacts list then select a name from the phone book to call.
3. Touch to enter history record list then choose a record number for calling.
4. Touch to enter Bluetooth setup, the following menu appears

• Bluetooth settings numu
• BT: on/off
• Auto Answer : on/off
• Auto Load Phonebook: on/off
• Load Phonebook :Touch [>]to loading Phonebook.
• Touch to search the surrounding Bluetooth Device. Make sure Bluetooth on device is enable and discoverable;AII devices searched will be displayed on the product screen.
• Touch to enter the paired mobile device. the following appears

• Touch the to disconnect the Bluetooth phone
• Touch the to connect the Bluetooth phone.
• Touch the to delete the device paired.

Hands-free Mode and Private Mode

• During a call, to switch between Hands-free mode and private mode; Touch to mute microphone so that the receiver hear from your side.
• Answer/dial out a call.
• Reject/cancel a call.

Bluetooth playback mode
Select In the main menu, press [ BT Music], the following menu appears.

• Touch to switch next track.
• Touch to switch previous track.
• Touch to pause playback, touch ►to play.

External audio/ video sources (AV-IN)

• Connect an external component to the AV-IN input terminal.
• Select AV-IN as the source.
• Turn on the connected component and start playing the source

Apple CarPlay (Wired and Wireless)

Connection

1. Connect iPhone to product USB1 port via lightning cable, the product screen will automatically show the CarPlay interface. User can operate the common functions of iPhone on the product. iPhone support : minimum iPhone; Required iOS: minimum iOS 7.1.
   

2. When connect iPhone via USB1 port you can select II Enable Wireless CarPlay” to enable wireless CarPlay. User can also go to Select Device list and then initiate wireless connection via Bluetooth pairing.
   

Call Out/ Receive Call
Touch the phone button on the main interface of CarPlay for Calling.

Play Music
Touch the music button on the main interface of CarPlay to play all of contents from iTunes.

Use Map
Touch the navigation button on the main interface of CarPlay to show the maps.

Siri

1. Touch and hold Apple Home key on the iPhone device for using Siri voice assistant, such as making a call, playing music, opening the map and other voice commands;
2. Touch the voice key on the front panel;
3. When iPhone is connected, enable Siri by steering wheel (some cars);
4. Control with II Hey, Siri11

Android Auto (Wired and Wireless)

1. Connect Android Auto compatible phone to product USB 1 port via standard USB cable. Drivers can enjoy music from their phone, show the way with Google map or other map App and make or receive a call. User need to enable Bluetooth on both phones and the product at the same time. Required Android 05:6.0. (Android Auto App must be installed on the phone before connecting)
2. User can also go to Select Device list and then initiate wireless connection via Bluetooth pairing.

Camera 1 Input

• This device features a video input at the rear of the device for connecting a left or right view camera that is available as an option (sold separately). If a left or right view camera is connected, the image is displayed on the screen, when select camera 1 as the source.
• When connect CAM 1 trigger wire to left or right lamp power supply can to view camera 1

Camera 2 Input

• This device features a video input at the rear of the device for connecting a left or right view camera that is available as an option (sold separately). If a left or right view camera is connected, the image is displayed on the screen, when select
  camera 2 as the source.

• When connect CAM 2 trigger wire to left or right lamp power supply can to view camera 2

Rear Camera Input
This device features a video input at the rear of the device for connecting a rear view camera that is available as an option (sold separately). If a rear view camera is connected, the image is displayed on the screen, when the reverse gear is engaged
Connect REVERSE wire to reverse lamp power supply to detect when the reverse gear is engaged.

External monitor

• This device features a video out for connecting an external monitor for passengers in the rear
• seat (see Connection diagram at the end of these instructions).
• Select the desired source via the main menu and start movie playback, e.g. from a USB.
• The image is displayed on the rear monitor.

Settings

System Settings

1. Touch to select language;

2. Touch to select date & time

3. Open/Close key beep

4. Open/Close hand brack

5. Touch to select SWC, the following menu appears.
   Open/Close SWC default switch, When user open SWC default switch, touch to select custom swc
   After the [ ] is touched, select the keys you wanted to set. Long press one steering wheel key to complete the function setting. One by one by pressing the steering wheel above key and records the order, click on the corresponding function settings ,touch [ ] to save settings.

6. Touch to select radio setup. Open/Close RDS; touch to select the region.

7. Touch to select factory reset, All the memories will be lost!

8. Touch to select GPS Connection Status form, View GPS position status.

9. Touch to select About. View the current software version.

Display Settings

Open/Close Lighting Detect

• Adjust daylight dimming level or night dimming level, when lighting detect is on, adjust night dimming level.
• Illumination settings, the following menu appears.
• Open/Close Led Auto. When Auto Led is on, backlit keys in automatic cycle display White/Red/Yellow/Blue/Green/Purple/Light Green, when the Led Auto is off, you can choose single color backlighting.
• Touch to enter wallpaper interface you can select your favorite wallpaper in the background
• Touch to enter change logo interface. the following menu appears..

you can change start screen logo, follow the steps below
BMP name is set to 1024 x 600 in the root directory of the USB flash drive.

Audio & EQ Settings

1. Adjust Balance/Fader, the following menu appears. Touch  or  to adjust fader & balance, touch  balance.

2. Touch to enter Subwoofer Output interface, the following menu appears. Open/Close subwoofer output.
   

   • Touch  or to adjust subwoofer level Oto+ 10.
   • Touch   or [  to adjust subwoofer phase 0°to 180°
   • Touch to enter subwoofer crossovers interface, the following menu appears..
   • Low Pass Filter adjustment. Use – and + to select frequency 60Hz, 80Hz, 100Hz, 120Hz, 160Hz and 200Hz
   • Use – and+ to set a crossover slope 12dB or 24dB

3. Open/Close Loudness effect.

4. EQ Settings, the following menu appears.. Select a preset equalizer via < or > Select EQ Custom to set the levels of the available frequency bands according to your preferences.
   You can adjust the equalizer for all sources. Touch the to enter the equalizer menu.
   Note : Touch the [Reset] to reset the customized setting again

5. Front and Rear Crossover, the following menu appears.

   • Use – and+ to select front or rear
   • Use – and+ to select frequency off, with all pass.
   • High Pass Filter adjustment. Use – and + to select frequency 60Hz, 80Hz, 1 00Hz, 125Hz.
   • Use – and + to set a crossover slope 12d B or 24d B.

6. Mic Select internal or external, When Internal is selected, the internal microphone is effective, and when External is selected, the external microphone is effective

Bluetooth Settings

1. Open/Close Bluetooth connection.
2. Pairing mode from Bluetooth device connection.
3. Displays the device name of the Bluetooth connected device
4. Users can modify the Bluetooth name
5. The user can clear connected or paired devices

Rear Camera Setting

1. When the rear camera View is set to normal, the video is in normal View. When the rear camera View is set to reverse, the video is in reverse View.
2. Open/Close parking assist guide. When the parking assist guide is set on, the Parking assist guide view is displayed
3. Users can adjust the parking assist guide. (Only the parking assist guide is seton.)

COMMON PROBLEMS AND SOLUTIONS

When there is a problem with the machine

1. Recovery to factory settings or reset;
2. Try reigniting
3. Please check the phenomena that described in the table below and try to use the solutions;
4. Contact Service Center

FOR MORE LANGUAGES, PLEASE SCAN QR CODE BELOW
PARA MAS IDIOMAS, FAVOR ESCANEAR EL CODIGO QR ABAJO
POUR PLUS DE LANGUES, VEUILLEZ SCANNER LE CODE QR CI-DESSOUS

BP Americas Corp.

• Doral, Florida 33178 USA
• www.bpcarusa.com
• BP Americas Paraguay S.A.
• Asuncion, Paraguay
• info@bpamericas.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>