RenewAire EV Series IAQ Sensor Instruction Manual
- June 15, 2024
- RenewAire
Table of Contents
RenewAire EV Series IAQ Sensor
Specifications
- Model: IAQ-D, IAQ-W
- Compatible with: EV-Series, SL-Series, EV Premium, HE-Series, LE-Series
Product Overview
The IAQ Sensor is an accessory for RenewAire products. It is designed to provide accurate indoor air quality measurements and control the operation of the Energy Recovery Ventilator (ERV) based on the IAQ sensor level.
Dimensions
IAQ-W
- Height: 3.3 inches
- Width: 1.15 inches
- Depth: 4 inches
IAQ-D
- Height: 3.5 inches
- Width: 1.15 inches
- Depth: 4.7 inches
Electrical
The IAQ Sensor requires wiring connections to the RenewAire unit’s control board. Refer to the wiring schematics provided below for the specific unit model:
Wiring Schematics
- Figure 3.1.0: Wiring Schematic for EV90, EV90P, EV130, EV200, EV240, EV300 Units Only
- Figure 3.1.1: Wiring Schematic for EV Premium and SL75 Units
- Figure 3.1.2: Wiring Schematic for HE1.5IN Units without ECM
- Figure 3.1.3: Wiring Schematic for HE1.5RT, LE-Series, and all HE2X and larger Units without VFDS or ECM
- Figure 3.1.4: Wiring Schematic for HE- and LE-Series Units with Factory-Installed VFDS
- Figure 3.1.5: Wiring Schematic for HE1.5 Units with ECM and Terminal Block
- Figure 3.1.6: Wiring Schematic for HE07, HE10, and HE1.5 Units with ECM and Circuit Board
Factory Assistance
If you require further assistance with the installation or wiring of the IAQ Sensor, please contact our customer support at 1-800-627-4499.
FAQ
Q: What is the purpose of the IAQ Sensor?
The IAQ Sensor is designed to measure indoor air quality and control the operation of the Energy Recovery Ventilator (ERV) based on the IAQ sensor level.
Q: Which RenewAire units are compatible with the IAQ Sensor?
The IAQ Sensor is compatible with EV-Series, SL-Series, EV Premium, HE-Series, and LE-Series units.
Q: How do I wire the IAQ Sensor to my RenewAire unit?
Refer to the wiring schematics provided in the user manual for your specific RenewAire unit model.
IAQ Sensor
Supplemental Wiring Manual for Accessories
- EV-Series
- SL-Series
- EV Premium
- HE-Series
- LE-Series
OVERVIEW
The Indoor Air Quality (IAQ) monitor uses an advanced MEMS metal oxide semiconductor sensor to detect poor air quality. The sensor reacts quickly to detect a broad range of VOCs such as smoke, cooking odors, bio-effluence, outdoor pollutants, and from human activities. The sensor captures all VOC emissions that are completely invisible to CO2 sensors and provides a linear analog signal output of 4–20 mA, 0–5, or 10–10 VDC and a Normally Open (NO) relay to control an alarm or ventilation fan in various ways.
DIMENSIONS
IAQ-W
ELECTRICAL
WIRING SCHEMATICS
In this example, the IAQ Controller turns the Energy Recovery Ventilator (ERV) on at High speed when the IAQ sensor level exceeds IAQ Controller Relay setting.
In this example, the ERV does not run while unoccupied, set by timer. During occupancy, the ERV runs at variable Speed. IAQ Controller sets speed based on IAQ sensor levels. Remove the potentiometers by cutting the wires at the potentiometer. Cap the orange and purple wires from the potentiometer with wire nuts.
FACTORY ASSISTANCE
In the unlikely event that you need assistance from the factory for a specific
issue, make sure that you have the information called for in the Unit Records
page in the Owner Information section of the unit manual. The person you speak
with at the factory will need that information to properly identify the unit
and the installed options.
To contact RenewAire Customer Service:
Call 800-627-4499
Email:
RenewAireSupport@RenewAire.com
About RenewAire
For over 40 years, RenewAire has been a pioneer in enhancing indoor air
quality (IAQ) in commercial and residential buildings of every size. This is
achieved while maximizing sustainability through our fifth-generation, static-
plate, enthalpic-core Energy Recovery Ventilators (ERVs) that optimize energy
efficiency, lower capital costs via load reduction and decrease operational
expenses by minimizing equipment needs, resulting in significant energy
savings. Our ERVs are competitively priced, simple to install, easy to use and
maintain and have a quick payback. They also enjoy the industry’s best
warranty with the lowest claims due to long-term reliability derived from
innovative design practices, expert workmanship and Quick Response
Manufacturing (QRM).
As the pioneer of static-plate core technology in North America, RenewAire is
the largest ERV producer in the USA. We’re committed to sustainable
manufacturing and lessening our environmental footprint, and to that end our
Waunakee, WI plant is 100% powered by wind turbines. The facility is also one
of the few buildings worldwide to be LEED and Green Globes certified, as well
as having achieved ENERGY STAR Building status. In 2010, RenewAire joined the
Soler & Palau (S&P) Ventilation Group in order to provide direct access to the
latest in energy-efficient air-moving technologies. For more information,
visit: renewaire.com
201 Raemisch Road | Waunakee, WI | 53597 | 800.627.4499 | RenewAire.com
Member of the S&P Group Family of Brands
2023 © RenewAire LLC 105917_004_NOV23
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>