edishine HLFL02M LED Floor Lamp Instruction Manual
- June 4, 2024
- edishine
Table of Contents
HLFL02M LED Floor Lamp
Instruction Manual
HLFL02M LED Floor Lamp
Thank you for your purchase.
Please contact us if you have any questions.
We will get back to you within 24 hours.
Please attach your Order ID so that we can serve you better.
CAUTION
- Before assembly, place all parts out on a clean flat surface and inspect each part for defects that may have occurred during shipping.
- Inspect wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there are any defects in the wire, DO NOT continue to assemble. Please send an email to our Customer Service immediately.
- Consult a qualified electrician if you have any electrical questions.
- Never drape clothes over the lamp.
- To reduce the likelihood of tipping over, we recommend placing the lamp behind furniture and keeping children and pets away.
- To prevent children from suffocating and choking, keep them away from packing materials.
- Please keep this manual and hand it over when you transfer the product.
Packing List
| Part | Description | Quantity |
|---|---|---|
| A | Column Floor Lamp | 1 |
| B | Base | 1 |
| C | Screw | 2 |
| D | Screwdriver | 1 |
| E | Adapter Connector | 1 |
| F | Adapter | 1 |
| G | Remote Control | 1 |
| H | Instruction Manual | 1 |
Assembly Instruction
Before assembly, please compare the accessories with the packing list to make sure all parts are present; install the adapter first to check if the product functions as intended.
- Align the screw holes of the Base (B) with the screw holes at the bottom of the Column Floor Lamp (A) and fix them with Screws (C).
- Connect the Adapter Connector (E) to the Adapter (F) and then spin the lock of the Adapter.
- Place the floor lamp where you need it and plug it into the power supply.
Function
REMOTE CONTROL INSTRUCTIONS
- ON/OFF Switch
- Speed+/Speed-：Adjust the speed of the light change
- Mode+/Mode-：Press +/- on Modes to get 358 lighting effects
- Brightness-/Brightness+: Adjust the lamp’s brightness
- Auto: Short press to play 358 lights effects automatically; long press for 5 seconds to enter RGB colorful jump mode for lamp test;
- Lock key: Remote control ID match, press 5 seconds for the one-to-one match (green light flashes 3 times), and press 5 seconds again to unmatch (white light flashes three 3 times);
- Set key: Adjust the RGB order, press 5 seconds and enter the setting menu, then press RGB buttons to adjust the RGB order, press R until the lamp bar shows red, G until green, B until the light bar shows blue, and exit after mediation.
- RGBW static monochrome mode.
Cycle play effect: In automatic play mode, press the “Setup” key once, and
then press the “Lock” key once, to grasp the current effect then cycle play
Memory function: The floor lamp can remember the brightness and mode of the
last adjustment.
Note
- There must be a direct line of sight between the Remote Control and the Signal Receiver (1).
- The Remote Control works within 26ft without obstacles, and the IR signal cannot pierce through glasses or walls.
Specifications
- Product Height: 44.9 IN.
- Diameter: Φ2 IN
- Base Diameter: 6.9 IN.
- Line Length：5.9 FT
- Materials: Plastic & Metal
- Input Voltage: 100-240VAC 60Hz
- Max. Wattage: 9W
- Operating Distance: 26FT
One Year Limited Warranty
EDISHINE warrants this product to be free from defects in material and
workmanship for a period of one year from the date of purchase.
The warranty is void if the damage is caused by misuse or improper
installation. Our dedicated customer service team will get back to you within
24 hours.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
V10826
Documents / Resources
|
edishine HLFL02M LED Floor
Lamp
[pdf] Instruction Manual
HLFL02M, 2AU8L-HLFL02M, 2AU8LHLFL02M, HLFL02M LED Floor Lamp, HLFL02M, LED
Floor Lamp, Floor Lamp, Lamp
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>