EAST OAK PTU23001 LED Patio Umbrella Owner’s Manual

: June 15, 2024
: EAST OAK

EAST OAK PTU23001 LED Patio Umbrella

EAST-OAK-PTU23001 LED Pat-Umbrella-product

Specifications

Model: PTU23001 PTU23003 PTU23002 PTU23004
Weighted base requirement: Minimum 31 lbs. (14 kg) if used through a table, or 70 lbs. (32 kg) if freestanding

IMPORTANT CAUTION

Please check all parts and components to ensure no damage or missing items before starting the product’s construction. If you have any problems or discover any missing parts, please contact customer service at support@eastoak.com.

Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
When using power tools, please adjust the gear to the minimum. Otherwise, it will cause damage to the parts.
Assemble on a soft surface such as a drop sheet or rug to avoid scratching.

SAFETY GUIDE

Patio umbrellas are only designed to provide protection from the sun NOT the wind.
NEVER open or operate this umbrella in wind conditions greater than 5mph (8kph).
NEVER use the tilt function in any wind (even a light breeze).
NEVER use excessive force on the crank handle to open or close the umbrella.
ALWAYS close and secure the umbrella when not in use or during any strong wind event, especially gusting wind and rain.
ALWAYS close the umbrella when unattended or not in use. If you are not sitting under it, the umbrella should be closed.
ALWAYS use the Velcro straps to properly secure the canopy to the frame when the umbrella is closed.
Umbrella bases are required (additional purchase) to secure this umbrella.
NEVER open or operate a patio umbrella without a base. It is important to use a correctly weighted base; more weight is always better than less weight. This model requires a MINIMUM base weight of 31 lbs. (14 kg) if used through a table, or 70 lbs. (32 kg) if freestanding.

FAILURE TO CAREFULLY OBSERVE THESE SAFETY WARNINGS CAN RESULT IN CATASTROPHIC DAMAGE TO YOUR UMBRELLA, POTENTIAL PERSONAL INJURY AND OR PROPERTY DAMAGE.

IMPORTANT INFORMATION

Suppose the umbrella shows ANY signs of stress or moves around excessively even when adequately weighted. In that case, it indicates the wind is too strong, and the umbrella must be closed and secured immediately.

CARE AND MAINTENANCE

To help extend the life of the polyester fabric and reduce the effects of fading, we strongly advise using a protective storage cover whenever the umbrella is not being used.
During extended periods of bad weather (especially through winter months), your umbrella should be stored inside in a dry place.
The polyester fabric has been treated to make it dirt and shower-resistant (not waterproof). If your umbrella gets wet, please allow it to fully dry before storing it away. The fabric can be cleaned with a soft brush, then use a damp cloth and mild detergent to remove any stubborn stains.

PARTS LIST

ASSEMBLY INSTRUCTIONS

Locate the plug at the top of the umbrella. Then, carefully insert the plug into the solar panel’s underside socket.
Place the solar panel on the top of the umbrella, taking care to conceal the wires inside the gap at the top, then gently turn the solar panel in a clockwise direction to attach it to the umbrella. Take care not to over-tighten, as this may damage the umbrella and the solar panel.
Attach bottom pole (B) to umbrella frame (A), then tighten in the counterclockwise direction.
Stand and secure the umbrella in a suitable base (not included). Then, secure the umbrella pole firmly by tightening the locking nut, as shown.
Locate the umbrella in direct sunlight to charge the batteries before first use. IMPORTANT NOTE: Charge the batteries for at least 8 hours in direct sunlight before first use. Failing to follow this step will shorten the lifespan of the rechargeable batteries and decrease the performance of the lights. Also, ensure the switch on the rib is set to the “OFF” ‘O’ position during charging.

OPERATING INSTRUCTIONS

To open the umbrella, unfasten the Velcro storage straps and gently pull out each umbrella rib by hand. At the same time, wind the crank handle gently in a clockwise direction.
CAUTION : Do not wind the crank in a counterclockwise direction to open as damage may occur.
Continue to wind the crank handle until the umbrella canopy is fully open and taut. Take care as over winding may damage the umbrella. Once the canopy is fully open, insert the support pin into the hole below the runner hub.
To tilt the canopy, push the tilt button with one hand and gently allow the canopy to tilt with the other hand. Release the button to lock in the position.
CAUTION : The tilt option should only be used on wind-free days. Use of the tilt function even in a light breeze is not recommended.
To close the umbrella, ensure the canopy is horizontal (never close the umbrella in the tilted position). Remove the support pin below the runner hub. Wind the crank handle counterclockwise until the canopy is fully closed.
Use the Velcro storage straps to secure the umbrella when not in use.

OPERATING THE LIGHTS

To operate the lights, turn the switch (located on the end of one rib) to the “ON” (‘I’) position. Ensure that it is set to the “OFF” (‘O’) position when the lights are not being used.
IMPORTANT: If the lights are accidentally left on during the day, the batteries will NOT charge, and the lights will not operate at night.

REPLACING THE BATTERIES

The batteries in your LED umbrella must be replaced at least once yearly (or when you feel the light is fading more quickly). You can purchase replacement batteries at specialty retailers. You will need three AA size 1.2v 1200mAh NIMH rechargeable batteries, the same as the ones included with this unit.
Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause them to leak.

NEVER dispose of batteries in the fire. Batteries must be recycled or disposed of as per state and local guidelines.
NEVER mix old and new batteries.
NEVER mix Alkaline, Standard (Carbon-Zinc) or rechargeable (Nickel Cadmium), or (Lithium) batteries together in the solar panel.

Twist the solar panel counterclockwise and remove it from the top of the umbrella.
Carefully pull the plug out of the socket under the solar panel. IMPORTANT: Do not pull the wire to remove the plug.
Set the solar panel upside down on a soft, clean surface to avoid scratching. Loosen all three screws on the bottom of the solar panel.
Carefully open the solar panel. Replace the batteries, matching the +/- on the battery with the +/- on the battery case.|}

EAST OAK PTU23001 LED Patio Umbrella

Specifications

Model: PTU23001 PTU23003 PTU23002 PTU23004
Weighted base requirement: Minimum 31 lbs. (14 kg) if used through a table, or 70 lbs. (32 kg) if freestanding

IMPORTANT CAUTION

Please check all parts and components to ensure no damage or missing items before starting the product’s construction. If you have any problems or discover any missing parts, please contact customer service at support@eastoak.com.

Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
When using power tools, please adjust the gear to the minimum. Otherwise, it will cause damage to the parts.
Assemble on a soft surface such as a drop sheet or rug to avoid scratching.

SAFETY GUIDE

Patio umbrellas are only designed to provide protection from the sun NOT the wind.
NEVER open or operate this umbrella in wind conditions greater than 5mph (8kph).
NEVER use the tilt function in any wind (even a light breeze).
NEVER use excessive force on the crank handle to open or close the umbrella.
ALWAYS close and secure the umbrella when not in use or during any strong wind event, especially gusting wind and rain.
ALWAYS close the umbrella when unattended or not in use. If you are not sitting under it, the umbrella should be closed.
ALWAYS use the Velcro straps to properly secure the canopy to the frame when the umbrella is closed.
Umbrella bases are required (additional purchase) to secure this umbrella.
NEVER open or operate a patio umbrella without a base. It is important to use a correctly weighted base; more weight is always better than less weight. This model requires a MINIMUM base weight of 31 lbs. (14 kg) if used through a table, or 70 lbs. (32 kg) if freestanding.

FAILURE TO CAREFULLY OBSERVE THESE SAFETY WARNINGS CAN RESULT IN CATASTROPHIC DAMAGE TO YOUR UMBRELLA, POTENTIAL PERSONAL INJURY AND OR PROPERTY DAMAGE.

IMPORTANT INFORMATION

Suppose the umbrella shows ANY signs of stress or moves around excessively even when adequately weighted. In that case, it indicates the wind is too strong, and the umbrella must be closed and secured immediately.

CARE AND MAINTENANCE

To help extend the life of the polyester fabric and reduce the effects of fading, we strongly advise using a protective storage cover whenever the umbrella is not being used.
During extended periods of bad weather (especially through winter months), your umbrella should be stored inside in a dry place.
The polyester fabric has been treated to make it dirt and shower-resistant (not waterproof). If your umbrella gets wet, please allow it to fully dry before storing it away. The fabric can be cleaned with a soft brush, then use a damp cloth and mild detergent to remove any stubborn stains.

PARTS LIST

ASSEMBLY INSTRUCTIONS

Locate the plug at the top of the umbrella. Then, carefully insert the plug into the solar panel’s underside socket.
Place the solar panel on the top of the umbrella, taking care to conceal the wires inside the gap at the top, then gently turn the solar panel in a clockwise direction to attach it to the umbrella. Take care not to over-tighten, as this may damage the umbrella and the solar panel.
Attach bottom pole (B) to umbrella frame (A), then tighten in the counterclockwise direction.
Stand and secure the umbrella in a suitable base (not included). Then, secure the umbrella pole firmly by tightening the locking nut, as shown.
Locate the umbrella in direct sunlight to charge the batteries before first use. IMPORTANT NOTE: Charge the batteries for at least 8 hours in direct sunlight before first use. Failing to follow this step will shorten the lifespan of the rechargeable batteries and decrease the performance of the lights. Also, ensure the switch on the rib is set to the “OFF” ‘O’ position during charging.

OPERATING INSTRUCTIONS

To open the umbrella, unfasten the Velcro storage straps and gently pull out each umbrella rib by hand. At the same time, wind the crank handle gently in a clockwise direction.
CAUTION : Do not wind the crank in a counterclockwise direction to open as damage may occur.
Continue to wind the crank handle until the umbrella canopy is fully open and taut. Take care as over winding may damage the umbrella. Once the canopy is fully open, insert the support pin into the hole below the runner hub.
To tilt the canopy, push the tilt button with one hand and gently allow the canopy to tilt with the other hand. Release the button to lock in the position.
CAUTION : The tilt option should only be used on wind-free days. Use of the tilt function even in a light breeze is not recommended.
To close the umbrella, ensure the canopy is horizontal (never close the umbrella in the tilted position). Remove the support pin below the runner hub. Wind the crank handle counterclockwise until the canopy is fully closed.
Use the Velcro storage straps to secure the umbrella when not in use.

OPERATING THE LIGHTS

To operate the lights, turn the switch (located on the end of one rib) to the “ON” (‘I’) position. Ensure that it is set to the “OFF” (‘O’) position when the lights are not being used.
IMPORTANT: If the lights are accidentally left on during the day, the batteries will NOT charge, and the lights will not operate at night.

REPLACING THE BATTERIES

The batteries in your LED umbrella must be replaced at least once yearly (or when you feel the light is fading more quickly). You can purchase replacement batteries at specialty retailers. You will need three AA size 1.2v 1200mAh NIMH rechargeable batteries, the same as the ones included with this unit.
Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause them to leak.

NEVER dispose of batteries in the fire. Batteries must be recycled or disposed of as per state and local guidelines.
NEVER mix old and new batteries.
NEVER mix Alkaline, Standard (Carbon-Zinc) or rechargeable (Nickel Cadmium), or (Lithium) batteries together in the solar panel.

Twist the solar panel counterclockwise and remove it from the top of the umbrella.
Carefully pull the plug out of the socket under the solar panel. IMPORTANT: Do not pull the wire to remove the plug.
Set the solar panel upside down on a soft, clean surface to avoid scratching. Loosen all three screws on the bottom of the solar panel.
Carefully open the solar panel. Replace the batteries, matching the +/- on the battery with the +/- on the battery case.|}

EAST OAK PTU23001 LED Patio Umbrella

Specifications

Model: PTU23001 PTU23003 PTU23002 PTU23004
Weighted base requirement: Minimum 31 lbs. (14 kg) if used through a table, or 70 lbs. (32 kg) if freestanding

IMPORTANT CAUTION

Please check all parts and components to ensure no damage or missing items before starting the product’s construction. If you have any problems or discover any missing parts, please contact customer service at support@eastoak.com.

Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
When using power tools, please adjust the gear to the minimum. Otherwise, it will cause damage to the parts.
Assemble on a soft surface such as a drop sheet or rug to avoid scratching.

SAFETY GUIDE

Patio umbrellas are only designed to provide protection from the sun NOT the wind.
NEVER open or operate this umbrella in wind conditions greater than 5mph (8kph).
NEVER use the tilt function in any wind (even a light breeze).
NEVER use excessive force on the crank handle to open or close the umbrella.
ALWAYS close and secure the umbrella when not in use or during any strong wind event, especially gusting wind and rain.
ALWAYS close the umbrella when unattended or not in use. If you are not sitting under it, the umbrella should be closed.
ALWAYS use the Velcro straps to properly secure the canopy to the frame when the umbrella is closed.
Umbrella bases are required (additional purchase) to secure this umbrella.
NEVER open or operate a patio umbrella without a base. It is important to use a correctly weighted base; more weight is always better than less weight. This model requires a MINIMUM base weight of 31 lbs. (14 kg) if used through a table, or 70 lbs. (32 kg) if freestanding.

FAILURE TO CAREFULLY OBSERVE THESE SAFETY WARNINGS CAN RESULT IN CATASTROPHIC DAMAGE TO YOUR UMBRELLA, POTENTIAL PERSONAL INJURY AND OR PROPERTY DAMAGE.

IMPORTANT INFORMATION

Suppose the umbrella shows ANY signs of stress or moves around excessively even when adequately weighted. In that case, it indicates the wind is too strong, and the umbrella must be closed and secured immediately.

CARE AND MAINTENANCE

To help extend the life of the polyester fabric and reduce the effects of fading, we strongly advise using a protective storage cover whenever the umbrella is not being used.
During extended periods of bad weather (especially through winter months), your umbrella should be stored inside in a dry place.
The polyester fabric has been treated to make it dirt and shower-resistant (not waterproof). If your umbrella gets wet, please allow it to fully dry before storing it away. The fabric can be cleaned with a soft brush, then use a damp cloth and mild detergent to remove any stubborn stains.

PARTS LIST

ASSEMBLY INSTRUCTIONS

Locate the plug at the top of the umbrella. Then, carefully insert the plug into the solar panel’s underside socket.
Place the solar panel on the top of the umbrella, taking care to conceal the wires inside the gap at the top, then gently turn the solar panel in a clockwise direction to attach it to the umbrella. Take care not to over-tighten, as this may damage the umbrella and the solar panel.
Attach bottom pole (B) to umbrella frame (A), then tighten in the counterclockwise direction.
Stand and secure the umbrella in a suitable base (not included). Then, secure the umbrella pole firmly by tightening the locking nut, as shown.
Locate the umbrella in direct sunlight to charge the batteries before first use. IMPORTANT NOTE: Charge the batteries for at least 8 hours in direct sunlight before first use. Failing to follow this step will shorten the lifespan of the rechargeable batteries and decrease the performance of the lights. Also, ensure the switch on the rib is set to the “OFF” ‘O’ position during charging.

OPERATING INSTRUCTIONS

To open the umbrella, unfasten the Velcro storage straps and gently pull out each umbrella rib by hand. At the same time, wind the crank handle gently in a clockwise direction.
CAUTION : Do not wind the crank in a counterclockwise direction to open as damage may occur.
Continue to wind the crank handle until the umbrella canopy is fully open and taut. Take care as over winding may damage the umbrella. Once the canopy is fully open, insert the support pin into the hole below the runner hub.
To tilt the canopy, push the tilt button with one hand and gently allow the canopy to tilt with the other hand. Release the button to lock in the position.
CAUTION : The tilt option should only be used on wind-free days. Use of the tilt function even in a light breeze is not recommended.
To close the umbrella, ensure the canopy is horizontal (never close the umbrella in the tilted position). Remove the support pin below the runner hub. Wind the crank handle counterclockwise until the canopy is fully closed.
Use the Velcro storage straps to secure the umbrella when not in use.

OPERATING THE LIGHTS

To operate the lights, turn the switch (located on the end of one rib) to the “ON” (‘I’) position. Ensure that it is set to the “OFF” (‘O’) position when the lights are not being used.
IMPORTANT: If the lights are accidentally left on during the day, the batteries will NOT charge, and the lights will not operate at night.

REPLACING THE BATTERIES

The batteries in your LED umbrella must be replaced at least once yearly (or when you feel the light is fading more quickly). You can purchase replacement batteries at specialty retailers. You will need three AA size 1.2v 1200mAh NIMH rechargeable batteries, the same as the ones included with this unit.
Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause them to leak.

NEVER dispose of batteries in the fire. Batteries must be recycled or disposed of as per state and local guidelines.
NEVER mix old and new batteries.
NEVER mix Alkaline, Standard (Carbon-Zinc) or rechargeable (Nickel Cadmium), or (Lithium) batteries together in the solar panel.

Twist the solar panel counterclockwise and remove it from the top of the umbrella.
Carefully pull the plug out of the socket under the solar panel. IMPORTANT: Do not pull the wire to remove the plug.
Set the solar panel upside down on a soft, clean surface to avoid scratching. Loosen all three screws on the bottom of the solar panel.
Carefully open the solar panel. Replace the batteries, matching the +/- on the battery with the +/- on the battery case.|}}
Make sure the O ring is correctly located before replacing the cover.
Re-assemble the solar panel. Do not over-tighten the screws.

FEATURES

• SOLAR-POWERED LIGHTS: Use day or night with 40 built-in solar LED lights and a center LED light. Lights can run for 6-7 hours simultaneously.
• HIGH-DURABILITY FABRIC: Made with high-quality, water-resistant fabric to last for years of enjoyment.
ADJUST YOUR SHADE: Stay cool at all times, as the easy push-button tilt system gives coverage no matter what time of day. Up to 45 degrees inclination, while a wind vent cools air under the umbrella. CONVENIENT CRANK HANDLE: Easy open/close system puts the umbrella up in just seconds with minimal effort.
QUICK SETUP: Detachable pole contributes to easy setup and storage.

WHAT’S IN THE BOX

1 x Main Frame and Canopy
1 x Lower Pole
1 x Solar Panel
3 x Spare LED Light Covers
1 x Owner’s Manual

TECHNICAL SPECS

• Construction Materials: 180g Polyester Canopy, Aluminum Pole, and Steel Ribs.
• Assembly Time: 1-5 minutes
• Product Size:
- Umbrella Ribs: 8 steel ribs
- Umbrella Pole Diameter: 1.9 inch

WARRANTY AND SERVICE

GUARANTEED 3-YEAR WARRANTY
Thank you for choosing East Oak. This product is covered by our company warranty for up to 3 years from its original purchase date.

CLAIM WARRANTY
If you’d like to claim your product’s warranty, register your new product on our website at www.eastoak.com/warranty.