home TORNADO Series Kitchen Extractor Hood Instruction Manual

KPE 6020S, KPE 6020W, KPE 6020B
TORNADO series
instruction manual

KITCHEN EXHAUST HOOD, TORNADO SERIES

Carefully read the instructions for use before using the appliance.
Illustrations contained in these instructions for use are only for reference, and always the actual version of the product applies.This instructions for use applies to multiple versions of the appliance. Accordingly, it may contain the description of functions, which do not apply to your actual appliance.
ADVICE AND RECOMMENDATIONS

WARNINGS INSTALLATION

• The manufacturer does not assume responsibility for damage due to erroneous or incorrect installation.

• The minimum safety distance between the cooktop and the exhaust hood is 650mm (some models may be installed lower, refer to the sections on dimensions and installation).

• Verify that the available mains voltage complies with the rated voltage of the exhaust hood indicated on the product label inside the appliance.

• In case of appliances with class I. contact protection, verify, whether the household power supply provides adequate earth protection.

• Connect the exhaust hood to an exhaust duct with a pipe of at least 120mm diameter. Keep the length of the exhaust duct to the minimum, as much as possible.

• Do not connect the exhaust hood to the flue of appliances that produce combustion products, or exhaust gases (gas heaters, fireplaces, etc.).

• If the exhaust hood is used with appliances other than electric (e.g. stove with gas burner), adequate ventilation must be ensured within the room, in order to prevent the backflow of exhaust gases. The kitchen should have an opening directly connected to outdoor air, to ensure the entry of fresh air.
  If the kitchen exhaust hood is used with appliances powered by other sources, than electricity, the negative pressure within the room may not exceed the 0.04 mbar value, in order to prevent the reverse suction of smoke and gases indoors by the exhaust hood.

• In the event of damage to the supply cable, the cable must only be replaced by the manufacturer or at an authorized service location, to avoid any potential risks.

• In case the installation instructions of a stove with a gas burner specifies a greater installation height, that distance shall be applied. Always observe the requirements applicable to air replacement.

USE

• Ensure adequate ventilation in the room, if the kitchen exhaust hood is used simultaneously with other appliances using gas or other fuel types (this does not apply to exhaust hoods, which return the air into the room when set to recycling ventilation).
• This exhaust hood is exclusively designed for household use, to eliminate smells in the kitchen.
• Never use the exhaust hood for purposes other than designated.
• Never leave a high open flame burning under the exhaust hood.
• Set the flame intensity so that it is directed towards the bottom of the pan, and it does not extend around the sides.
• Fryers should be continuously monitored during use: oil can catch fire, if overheated.
• Avoid the use of open flames under the exhaust hood, as this presents a risk of fire.
• This appliance can be used by children aged 8 years or above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, provided that they are supervised or have been given instructions concerning the safe use of the appliance and understand the hazards involved.
• Keep children supervised. Do not allow children to play with the appliance.
• Cleaning and user maintenance may not be carried out by children without proper supervision.
• CAUTION : Accessible parts of the exhaust hood may become hot, if used together with cooking appliances.

MAINTENANCE

• Regularly clean the kitchen exhaust hood and its filter, according to the given instructions.
• Before starting any maintenance work on the appliance, disconnect the plug from the mains socket.
• Clean the exhaust hood with a moistened cloth and neutral liquid detergent.
• This appliance serves up to 4 cooktop units.

DISPOSAL

Waste equipment must be collected and disposed separately from household waste because it may contain components hazardous to the environment or health. Used or waste equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of product at a facility specializing in the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local waste management organization. We shall undertake the tasks imposed upon the manufacturer pursuant to the relevant regulations and shall bear all associated costs arising from such.

MAIN PARAMETERS

Rated voltage and frequency: 220–240 V~ / 50 Hz
Drive motor rated input: 38 W
Grease filter: KPE 60/A
Carbon filter: KPE 6020/C
Under certain circumstances, electric appliances carry a risk.

PARTS

DIMENSIONS

INSTALLATION

DRILLING AND MONTING THE BRACKET

• Carefully read the instructions for use.
• Remove the exhaust hood from its packaging and verify the operation of all of its functions. Verify, whether the rated voltage (V) and frequency (Hz) indicated on the product label is equivalent to the supply voltage and frequency available at the installation site.
• Ensure there is no electric wiring, piping, etc. behind the mounting surface to be drilled.
• Stainless steel and glass surfaces of the exhaust hood can easily get damaged, if scratched or impacted by the tools during installation. Pay attention to the protection of these surfaces during installation.
• Protect the surface of the cooktop below with a sheet of cardboard paper or similar means, to avoid causing any damage during the installation of the exhaust hood.
• The manufacturer does not take responsibility for failure to observe safety regulations applicable to the correct and normal use of electric appliances.

Select the Ventilation Mode:

INFORMATION

• Adequate combustion and gas exhaust requires the presence of a sufficient amount of air in the flue (chimney) of appliances using combustible fuels, in order to prevent reversed air-flow.
• In the course of evaluation of air-pressure, the entire ventilation system of the house/flat needs to be considered.
• Authority regulations applicable to the delivery of extracted air must be observed. If the exhaust hood is used in recycling ventilation mode with an activated carbon or cotton filter, no limitations apply to the operation of the appliance.
• If external ventilation mode is preferred, two types of ventilation methods are possible, by “horizontal connection” and “vertical connection”. Use a suitable too to remove the cover, and install the butterfly-valve into the opening before use.
• The square-shaped butterfly valve required for “horizontal connection” is not included in the supply.

Preparation of Installation:

Before the commencement of installation works, ensure that the appliance is disconnected from power supply. The plug should be positioned to ensure easy disconnection and connection.
The help of two persons will be required to install the exhaust hood. The following tools and materials will be required to complete installation.
Required tools:

• Drill suitable for the type of wall
• Phillips head screwdriver
• Measuring band
• Kitchen saw or jigsaw
• Installation and electrical connection should be performed by a qualified person, with he observation of all applicable rules and standards, also including the consideration of fire-resistance.
• Do not vent the extracted air into to the flue (chimney) of other appliances using gas, or other combustible fuels.
• Always observe the requirements applicable to air discharge.
• The kitchen exhaust hood should be positioned at a height of at least 65cm, and up to 75cm from the cooktop.

INSTALLATION INTO CABINET

• Drill a hole of 130mm diameter and four holes of 3.5mm diameter arranged, as shown on the imagebelow.
• Warning: Failure to follow these instructions for the installation of bolts and the fastening devicemay result in electric hazards.
• CAUTION: If the kitchen exhaust hood will be used in recycling ventilation mode, the 130 mmdiameter hole is not required.
• Fasten the exhaust hood to the kitchen cabinet using the 4 bolts. Temporarily fitting the exhausthood, check the correct position of mounting bolts. If correct, set the appliance into position. Tightenthe bolts, if needed.

INSTALLATION ON WALL

• To mount the exhaust hood on the wall, drill the top two holes of 10mm diameter at a distance of 538 mm, symmetrical to the exhaust outlet in the middle, as shown on the image below. Ensure that the exhaust hood is positioned exactly above the cooktop.
• Fit two plastic dowels (included) into the holes.
• Place two bolts into the top two dowels, and tighten them so that they protrude by 3mm from the wall surface.
• Hang the kitchen exhaust hood on the top two bolts and mark the position of the two bottom bolts.
• Remove the exhaust hood from the wall, drill the two bottom holes, then fit the plastic dowels into the holes.
• Hang the exhaust hood on the top two bolts, fit the bottom bolts and tighten them all.

OPERATION

| DRIVE MOTOR SWITCH: Press this switch to stop the operation of the drive motor.
---|---
| ENGINE SPEED SWITCH: By pressing this switch the drive motor changes to LOW speed (rpm) operation.
| ENGINE SPEED SWITCH: By pressing this switch the drive motor changes to MEDIUM speed (rpm) operation.
| ENGINE SPEED SWITCH: By pressing this switch the drive motor changes to HIGH speed (rpm) operation.
| LIGHT ON/OFF SWITCH: Press to turn the lighting on, and press again to turn off.

LIGHTING

REPLACING THE LAMP

• Turn off the exhaust hood and disconnect the plug from the mains socket, or switch off the cut-out, or fuse.
• Remove the grease filter.
• Apply tension on the lamp and remove it from its holder (this might require the exertion of pressure or force).
• Disconnect the lamp connector.
• Replace the lamp with a new one of equivalent type, and ensure that it is correctly connected to the connector.
• Reconnect the power supply by plugging the supply cable plug into the wall socket, or by switching the cut-out, or fuse back on.
  | Maximum output| Voltage| | Lamp base| ILCOS D code
  ---|---|---|---|---|---
  With built-in adapter
  LED-modules| 1.5 W| 220 V-240 V| Rectangle:
  33.2 mm x 120 mm| | DBS-1.5-H-33.2/120

INFORMATION
Regularly clean the ventilation fans. Prevent the accumulation of thick grease on the fan blades.

CLEANING AND MAINTENANCE

Before cleaning, maintenance or servicing, disconnect the kitchen exhaust hood from the power supply.

• Regularly clean the surfaces of the exhaust hood. To clean the exhaust hood use mild soap or detergent.
• Avoid using strong bases or scrubbing materials.
• Avoid using scrubbing materials and dish-washing liquid.
• The metal grease filter can be cleaned using mild soap or detergent. (Strong deposits of grease are difficult to remove and the filter might need to be replaced.)
• The activated carbon filter cannot be cleaned, it needs to be replaced regularly.

Information
Do not allow water to enter the electrical parts of the drive motor, the control switch, etc. during cleaning.

It is recommended to clean the metal grease filter every three months, according to the followinginstructions:

• Remove the metal grease filter from the kitchen exhaust hood and clean it in a solution of water andmild liquid detergent. Let soak.
• Rinse thoroughly with hot water and let dry completely.
• The colour of the metal grease filter may change after it was cleaned several times. This is no reasonfor raising complaints, or to replace the metal grease filter.

Information
Failure to carry out the cleaning procedure as instructed will cause a risk of fire.

FITTING THE BUTTERFLY-VALVE
Hold the butterfly-valve in hand and adjust it to the exhaust outlet, as shown on the image. Fit the butterfly-valve into position and turn until the three claws of the valve seize. Installation is now complete. The mounting type of outside air baffles and of butterfly-valves must comply with the requirements of the IEC/EN 60335-1 standard.

REPLACEMENT, INSTALLATION OF THE CARBON FILTER

• Remove the grease filter.
• The carbon filter is located on the drive motor. Turn the carbon filter until unscrewed.
• Replace the carbon filter with a new one, and reassemble the unit by performing the above steps in reverse order.
  Warning : The carbon filter is not washable or recyclable. It needs to be replaced after approximately 2–3 months of use.

TROUBLESHOOTING

the blades.
The condenser is damaged.| Replace the condenser.
The drive motor is damaged.| Replace the drive motor.
The internal wiring of the drive motor is cut off/ disconnected. There is an unpleasant smell present.| Replace the drive motor.
Neither the lighting, nor the dnve drive motor run.|  in addition to the above, check the following:
, ii he lighting is damaged.| Replace the lamps.
The supply cable is loosened.| Connect the cable according to the wiring diagram.
Oil leak present.| The outlet and the inlet of the vent are not sealed properly.| Remove the outlet and seal with adhesive sealant.
Vibration occurs.| The blade can cause vibration, if damaged.| Replace the blade.
The drive motor is not fastened tightly.| Fasten the drive motor tightly.
The exhaust hood is not fastened tightly.| Fasten the exhaust hood tightly.
Insufficient suction.| The distance between the exhaust hood and cooktop is too big.| Readjust the distance.
Too much ventilation due to opened doors or windows.| Select a new location for the installation of the appliance, or close some of the doors/windows.
The appliance is askew.| Mounting bolts are not tightened enough.| Tighten the mounting bolts and adjust the appliance horizontally.
Hangers are not tightened enough.| Tighten the hangers and adjust the appliance horizontally.

Producer
SOMOGYI ELEKTRONIC ®
• H – 9027 • Győr, Gesztenyefa út 3.
• www.somogyi.skTel.: +421/0/35 7902400Ul. gen. Klapku 77, 945 01 Komárno, SKDistributor: SOMOGYI ELEKTRONIC SLOVENSKO s. r. o.www.somogyi.hu

References

• Zed d.o.o.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>