INMOTION N400 TC4 Series X Receiver Instruction Manual
- June 15, 2024
- INMOTION
Table of Contents
INMOTION N400 TC4 Series X Receiver
Guarantee, service, repairs and maintenance
Inmotion Controls, Inc. products are covered by a guarantee/warranty against
material, construction and manufacturing defects. During the
guarantee/warranty period, Inmotion may replace the product or faulty parts.
Work under guarantee/warranty must be carried out by Inmotion Controls, Inc.
The f0110Ming are NOT covered by the guarantee / warranty:
- Faults resulting from normal wear and tear
- Parts of a consumable nature such as pushbuttons, relays, ålses etc. that have been subject to unauthorized modifications
- Faults resulting from incorrect installation and use
- Condensation and water damage
Maintenance
- Repairs and maintenance must be carried out by qualified personnel.
- Use spare parts from Inmotion Controls, Inc. only-
- Contact your representative if you require senice or other assistance.
- Keep the product in a dry, clean place.
- Keep contacts and antennas clean.
- Wipe off dust using a slightly damp, clean cloth.
INTENDED USE
The HS and Receiving units are intended as the control unit interface for the Radio Remote Control for Hoists, Cranes, Monorail, and Material Handling equipment.
OPERATING METHODS
The receiving unit accepts signals from the Radio Transmitter and processes them to open or close specific relays for Hoist, Trolley, Bridge, and various auxiliary functions.
Customer Information
Thank you for purchasing an Inmotion Controls, Inc. radio remote control. READ ALL INSTRUCTIONS CAREFULLY BEFORE MOUNTING, INSTALLING AND CONFIGURING THE PRODUCT. This manual includes general information concerning the operation of the radio remote control transmitter.
General Information on Safety
- Persons under the influence of drugs and/or alcohol and/or other medicine that impairs their reaction may not assemble, disassemble, install, put into operation, repair or operate the product.
- All conversions and modifications of an installation/system must conform to the relevant safety requirements. Work on the electrical equipment must be performed only by qualified, authorized personnel and under the relevant safety requirements.
- In the event of malfunctioning, visible defects or irregularities, the product must be stopped, and switched off and the relevant master switches must be switched off.
FCC Part 15 FCC ID : RX-(RN489896162-B0129) / TX-(RN489896162-B0134)
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( l) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
- You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
European Union Regulatory Notice
This device bearing the CE marking complies with the essential requirements
and other relevant provisions of Directive 1999/5/EC. This device complies
with the following harmonized European standards.
- safety: EN 60950-1 :2006+Al 1
- EMC: ETSI EN30 1489-1 Vl.9.2 2001-09; ETSI EN 301 489-3 Vl.4 .1 2002-08
- Radio: ETSI EN 300 220-1 v2.4.1: 2012; ETSI EN 300 220-2 v 24.1:2012 The following CE marking is valid for EU-harmonized telecom products.
IC Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: ( I ) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
General Description
Transmitter
STOP, ON/OFF
The N series transmitter has a STOP button on the button side. The STOP
switch has 2 functions:
- Press to “STOP’.
- Press 5 secs for turn the ON and OFF transmitters.
Start the transmitter.
- Press 5 secs for turn ON the transmitter.
- Press the ” START’
Turning the transmitter off
Press ( ) 5 secs to turn OFF the transmitter. The transmitter turns off All
relays deactivate.
Change the batteries
BATTERY TYPE: 2 x 1.5V(LR03 AAA)
- Remove the battery cover
- Remove both batteries.
Receiver
WARNING! The receiver must NOT be opened by any other than a qualified installer- Make sure to turn the electricity off before opening the receiver.
Wiring Diagram
Troubleshooting
Transmitter
Receiver
Should an error occur, the LED of the receiver will indicate the cause.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>