VIKING VS-12BL Biometric Wall Mounted Safe User Manual

VIKING VS-12BL Biometric Wall Mounted Safe

MODELS:

• VS-12BL WALL SAFE
• VS-14BL TOP OPENING DRAWER SAFE
• VS-20BLX MINI
• VS-25BL
• VS-25DBLX (VS-25DBL ) SMALL DEPOSITORY SAFE VS-35BLX (VS-35BL )
• VS-38BLX (VS-38BL) EXTRA WIDE LAPTOP SAFE VS-50BLX (VS-50BL ) LARGE
• VS-52BLR (VS-52BL*) HIDDEN WALL SAFE
• VS-52BLX HIDDEN WALL SAFE LASER CUT
• Models may change name with improvements and modifications

DISCLAIMER: Not recommend for a ge groups 55 and above. Due to th inning fingerprints, ALL fingerprint readers will lose accuracy with increasing age.

IMPORTANT· READ FIRST

TEST ALL FUNCTIONS OF YOUR SAFE. THEN BOLT IT DOWN TO A PERMANENT LOCATION.

• If you used Key to UNLOCK your safe, use Key to Lock it. If you USED PIN or Fingerprint, LOCK it electronically with # button.
• When the Key is used to UNLOCK your safe ALL electronic functions are disabled, thus locking with # button will not work.
• If you used Key to UNLOCK your safe the Key cannot be removed in UNLOCKED position. Lock your safe with key and remove key. (For more information see TIPS AND TROUBLESHOOTING)
• When putting batteries in or replacing it MAKE SURE your safe is in LOCKED position.
• Remember to register NEW PIN, or else anyone can open your safe with Default PIN.
• In default mode fingerprint function is disabled. To activate it register at least one fingerprint.
• Remember to register the same fingerprint in multiple positions.
• You cannot remove only one set of fingerprints. You must Reset your safe and set it up again.
• When Reset to factory default mode, only Default PIN or Key can open the safe.
• When low battery is shown ” “, replace with new batteries. All registered fingerprints and PIN will be SAVED.
• Sounds can be turned ON/OFF, except Warning Beep. (*Warning Beep is disabled if the safe is unlock with Key).
• Multiple use of incorrect PIN or fingerprint will put your safe On HOLD for 2 minutes.
• When on HOLD only the Key can unlock your safe.
• Do NOT store the Keys to your safe inside the safe.

DISCLAIMER: Most all fingerprint biometric readers loose accuracy and become inconsistent due to worn out, damaged or thinning skin associated with aging.
DISCLAIMER: The functionality and setup of Viking safes may vary between batches. Check Viking’s website for latest User’s Manual and tips.

GENERAL DESC RJPTION

• A Fingerprint Registration/Reset Button
• B  Battery Compartment
• C Locking Bars
• D LED light
• E Motorized Door
• F Fingerprint Reader
• G LCD display
• H Battery Indicator
• I Keypad
• J  Fingerprint Activation Button *
• K Confirm Button #
• L Logo Plate and Key Access

NOTE

• If you Unlock your safe with Key, use Key to Lock it.
• If you Unlock it with PIN or Fingerprint, LOCK it electronically with #

BEFORE FIRST USE

1. UNLOCK your safe with Key and open the door. (Remove Logo Plate, to access the keyhole)

2. With door open, LOCK the safe with Key and remove the Key.

3. Install batteries while the safe is in LOCKED position. Press any button on the keypad and look for the battery indicator icon on the LCD screen confirming your safe has power.

4. Then UNLOCK your safe electronically with PIN 1234 # and proceed with set up: change PIN and add fingerprints.
   REMEMBER: All Electronic functions of your safe are disabled when your safe is in LOCKED position – Locking Bars Stick Out. Lock the safe with Key, Remove the Key and UNLOCK your safe electronically to proceed with Set up.
   Unlock the safe electronically means using PIN or registered fingerprint. However, if the safe is new and/or in Default mode only factory default PIN 1234 # will unlock the safe. Fingerprints function is disabled in Factory Default Mode.

HOW TO RESET SAFE TO FACTORY DEFAULT SETTINGS

1. PRESS and HOLD down Reset Button 0 for 10 seconds or until you see “INIF” on the screen. Your safe is reset to Factory Default. All data is deleted, and you can begin with Set Up.

HOW TO CHANGE PIN CODE ON KEYPAD

• Step 1: Enter the Default PIN 1234 and HOLD down# until(——) shows up (1-2 seconds).

• Step 2: Enter your New PIN Code and #. Wait for the Beep. and enter# AGAIN. (Do NOT hold down #). You will see OK on the screen confirming New PIN code is registered.
  Note: You enter your New PIN only once, but you Enter# twice. Please, test to ensure only your New PIN will unlock the safe.

• Step 3: Test. Enter the Old/Default PIN code 1234 #- it should give show ERR. Safe remains locked.
  Enter your New PIN Code# – The safe should unlock.
  Note: Should you need to change a Registered PIN follow the same steps using your Registered PIN instead of the Default PIN.
  Note: When Reset to factory default mode, by holding down the Reset Button A for 10 seconds all data is erased. Only Default PIN or Key can open the safe. To change it to your New PIN Code again, follow the steps above.

HOW TO REGISTER FINGERPRINTS ON FINGERPRINT SCANNER

1. Unlock your safe using PIN (Do Not Use Key)

2. To register fingerprints, PRESS BRIEFLY Reset button A. As soon as Green Light comes on, place your fingerprint on the Glass Fingerprint Reader F  LCD screen will display “- IN -“. One fingerprint is registered.
   Repeat this step up to 32 to add more fingerprints.

3. If the registration fails “Err” will be displayed on LCD screen. Register the same finger again by repeating Step 3.1.

4. Repeat Step 3.1 with the same fingerprint but change fingerprint position on the Glass Fingerprint Scanner – left,right, up, down, to the side.
   Note: The more times and various positions you program one fingerprint the more likely it is to open in an emergency.

5. To register a completely different fingerprint, repeat

NOTE

• If you your safe with Key, use Key to it.
• If you it with PIN or Fingerprint, LOCK it electronically with #

HOW TO UNLOCK AND LOCK THE SAFE WITH YOUR FINGERPRINT

1. UNLOCK: Press Fingerprint Activation Button * when Green light comes on, place registered fingerprint on the Glass Fingerprint Reader. “OPEN” will be displayed on LCD screen. Safe is Unlocked.
2. LOCK: Close the door and Press# button
   Note: Do Not Use Key to lock the safe if you UNLOCKED it with fingerprint.

HOW TO UNLOCK AND LOCK THE SAFE WITH PIN CODE

1. UNLOCK: Enter a registered PIN and # (do not hold down#). 5.2. LOCK: Close the door and Press # button.
   Note: Do Not Use Key to lock the safe if you UNLOCKED it with PIN.

HOW TO UNLOCK AND LOCK THE SAFE WITH A KEY

1. UNLOCK: Insert the key in the keyhole and rotate to the right/clockwise to unlock.
2. LOCK: Insert the key and Rotate left/anticlockwise.
   Note: Do Not Use Key to lock the safe if you UNLOCKED it with PIN or Fingerprint

HOW TO TURN SOUNDS ON/ OFF

SOUNDS ON: Press 1 & star button, you will hear a long beep, sound is on. 7.2. SOUNDS OFF: Press O & star button, the sound is off.

HOW TO INSTALL/CHANGE BATTERIES ON LED LIGHT

1. Unscrew the little screw. Carefully pull down the LED light on the screw side on the left. Put 2 fresh AA batteries on the back of the light. Put Back the LED light starting on the right side of the LED light first.
   Note: 2 AA batteries are provided and have to be installed.

TIPS AND TROUBLESHOOTING

Note: If you Unlock your safe with Key, use Key to Lock it. If you Unlock it with PIN or Fingerprint, Lock it electronically with #

MOUNTING INSTRUCTIONS

TEST ALL FUNCTIONS OF YOUR SAFE.? BOLT IT DOWN TO A PERMANENT LOCATION.

Note: The safe may be mounted to a wall or floor. Be aware of the load bearing. Failure to do so can result in personal injury and/or damage to property. Use appropriate tools when performing work and always use eye protection

Wall Mounting

• Do not mount the safe without anchoring to the wall
• Find the studs in the wall, at your desired location. Most studs are 16 inches or 24 inches apart
• Check the wall for concealed wires or pipes
• Measure the location of the pre-set drill holes; mark their exact position onto the wall ensuring that the studs or anything else behind will not interfere
• Drill the appropriate size holes for the anchors you are using
• Carefully press the anchor into the holes at this time
• Mount the safe by running screws from inside of the safe and securing to anchors; ensure the safe is mounted securely.

Floor Mounting

• Measure the location of the pre-set drill holes; mark their exact position onto the floor
• Drill the appropriate size holes for the anchors you are using
• Carefully press the anchor into the holes at this time
• Mount the safe by running screws from inside of the safe and securing to anchors; ensure the safe is mounted securely.

WARNING

Never store firearms and ammunition together. The safest protection against accidents involving children is to store your firearm unloaded in an approved Firearm Safety Lock Box, with ammunition stored separately.

MOUNTING METHOD

Fix the safe in the place which is not easy to move.

• Drill holes for expansion bolts (or clamping screws) in the right place.
• Turn the expansion bolts counterclockwise to separate.
• Use the expansion bolts (or clamping screws) to secure the safe to the wall.
• Make sure the safe is mounted in place as required and then tighten all screws.

CAUTION
Use the expansion bolt when there is a concrete wall surface. Use the clamping screw when there is a wooden wall surface.

CARE AND MAINTENANCE

To maximize the security and performance of the safe, keep Glass Fingerprint Scanner F clean

• Use a dry cloth to remove any smudges or prints off the Fingerprint Scanner after use
• Use gentle cleaning agents to clean the safe and Glass Fingerprint Sacnner
• Test registered fingerprints and PIN code every 6 months
• Keep liquids away from the control panel. Spills on the control panel will cause damage and possibly electric shock
• Secure safe in a proper area to prevent from falling and causing damage or injury
• DO NOT disassemble the product. For all repairs, contact Viking Security Safe Customer Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>