DANCING OWS Pro Open Ear Bluetooth Headphones User Manual
- June 15, 2024
- DANCING
Table of Contents
Oladance OWS C1
List of items
Product introduction
Multipoint connection
Enable multipoint connection: After the first device is connected, press and
hold the buttons of both earphones at the same time for 2 seconds, and after
hearing the tone, the headset enters pairing mode again, and the second device
can search for the headset and connect.
Disconnect multipoint connection: When the headset has been connected to 2
devices, press and hold the buttons of both headsets at the same time for 2
seconds, and disconnect all Bluetooth devices and enter pairing mode after
hearing the tone.
| Operation temperature: 0~45°C Input: 5.0V **1A
---|---
Product name| Alamance OWS C1**
---|---
Product model| OLA07
Bluetooth protocol| HFP/A2DP/AVRCP/HSP
Working frequency| 2402-2480MHz
Disposal and Recycling Information
This symbol (with or without a solid bar) on the device, batteries (included),
and / or the packaging, indicates that the device and its electrical
accessories (for example, a headset, adapter or cable) and batteries should
not be disposed of as household garbage.
Battery warning
The built-in lithium battery of the product is forbidden to be
disassembled, impacted, extruded or put into fire. The battery under the very
low air pressure may result in explosion or flammable liquid or gas leakage.
Avoid the battery in a high-temperature environment or being exposed to strong
sunlight to avert explosion. Don’t use the battery continuously in case of
serious ballooning. The battery shall be handled pursuant to the local
regulations and shall not be disposed as household garbage. Don’t try to
repair, remove or refit the battery. The explosion may happen if the battery is
replaced by the one subject to incorrect model. Don’t compress or puncture the
battery with hard object. The battery leakage, overheating or outbreak of a
fire may occur if the battery is destroyed.
Declaration of Conformity
Hereby, Shenzhen Dancing Future Technology Ltd., declares that this device is
in compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following internet address:
http://oladance.com
SAR: RF exposure information: The EIRP power of the device at maximal case is
below the exempt condition, 20mW specified in EN 62479: 2010. RF exposure
assessment has been performed to prove that this unit will not generate the
harmful EM emission above the reference level as specified in EC Council
Recommendation (1999/519/EC).
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement.
RF Exposure
The portable device is designed to meet the requirements for exposure to radio
waves established by the FCC RF exposure guidelines. These requirements set a
SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value
is measured at a distance of 0mm between the radiator and the Head. The
highest reported Head SAR value: 0.48W/kg.
RF Exposure
The portable device is designed to meet the requirements for exposure to radio
waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg
averaged over one gram of tissue. The highest SAR value is measured at a
distance of 0mm between the radiator and the Head. The highest reported Head
SAR value: 0.48W/kg.
FCC ID:2A9AR-OLA07L FCC ID:2A9AR-OLA07R IC:29727-OLA07L IC:29727-OLA07R
HVIN:OLA07L HVIN:OLA07R
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 0cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Warning:
- Don’t place the product into a liquid environment or avoid the product exposed to high humidity
- Avoid extrusion to avert the damage to the product
- Don’t attempt to dismantle the product. Put the product in a cool and dry place to keep it dry if stored for a long time
- Avoid touching the strong magnet to prevent the magnetic headset from being demagnetized.
- Avoid the dusty, wet and dirty environment where the electronic circuit of the equipment may be damaged if being used.
- Don’t Use the equipment at the moment of thunderstorm because the thunderstorm may incur equipment fault or shock hazard.
- Don’t use the equipment when riding a motorcycle or a bicycle,driving a car or crossing the road to ensure your safety.
- Keep the equipment out of reach of children or pets to avert the damage.
- Don’t wash the equipment with chemical cleanser or strong detergent
Don’t Listen to the voice under high sound pressure and high volume for a long
time to prevent the possible hearing impairment when the headset is used.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference.
- this device must accept any interference, including interference that may cause undesired operation of the device.
How to wear the headphones correctly
Description of the LEDs
| Flashing white light: Bluetooth pairing/connecting
Solid white light: Bluetooth connection successful
Flashing red: Headphones are less than 5% battery
Solid red light: Headphones charging
White light flashes alternately red: headphones on/off
The indicator light is off: Charging of the earbuds is complete
---|---
| Blinking white: The headphones are charging
The indicator light is off: Charging of the earbuds is complete
Sound For Comfort
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>