UNIFULL ‎FMAM-ZNMSF007 Smart Keyless Entry Door Lock Installation Guide

UNIFULL ‎FMAM-ZNMSF007 Smart Keyless Entry Door Lock

Product Information

Specifications:

1. Smart lock*1
2. Doorbell*1
3. Latch*1
4. Key fobs*2
5. Physical keys*2
6. Box striking plate*1
7. Mounting plate*1
8. Protective pad*2
9. Lock cylinder*1
10. Nuts*3
11. Screws*9

Product Usage Instructions

Dimensioning:
Before drilling the hole, please check the dimensions and follow the instructions below:

1. Measure to verify that the hole on the door is 2-1/8 (54mm) in diameter.
2. Make sure the distance from the edge of the door to the center of the hole is 2-3/8 (60mm) or 2-3/4 (70mm).
3. Check if the hole on the door side is 1 (25mm) in diameter as shown in the picture.
4. The thickness of the door should be 1-3/8 to 2 (35 to 50mm).

Reversible Handle Adjust for Left Opening or Right Opening **

**

Note: The initial state of the smart lock handle is suitable for right- opening doors.

1. Move downward the handle at a 45-degree angle till you see the screws inside.
2. Unscrew the screws.
3. Move the handle 270 degrees backward till you see the screw holes.
4. Screw the screws back
5. In this way, the shift from left/right opening way is done.

Insert the Bolt or Latch:

Trim size: 3/4 (19mm)
Screw: 2
Proceed to the next step without adjustment.
Pinch and pull the square hole to adjust the length of the lock tongue.

Install the Strike Plate on the Door Frame:
Trim size: 3/4 (19mm)
Screw: 2
The door frame holes should be drilled at least 1/2 (12mm) deep.

Install Door Lock

1. Fit the rubber pad on the outer panel and tighten the 3 screw pipe strings.
2. Fix the lock cylinder according to the left or right opening way. Make sure the triangle arrow on the lock cylinder groove corresponds to the left or right door-opening direction you want to set.
3. Pass the outer panel power cord through the door hole and out from the other side.
4. Fit rubber pad on the metal retaining plate beneath the lock as shown in the picture, then screw the three long screws into the corresponding holes.
5. Connect the two terminals. Check the positive and negative of the plug before using. Do not forcibly insert or remove the plug to avoid damage.
6. Fix the back panel with screws one by one.
7. Insert the battery, close the battery cover, and complete the installation.

Important
Please pay attention to the step 2  of installation of the lock, the set of left/right openning issue

FAQ

1. Q: What are the dimensions for drilling the hole?
   A: The hole on the door should be 2-1/8 (54mm) in diameter. The distance from the edge of the door to the center of the hole should be 2-3/8 (60mm) or 2-3/4 (70mm). The hole on the door side should be 1 (25mm) in diameter. The thickness of the door should be 1-3/8 to 2 (35 to 50mm).

2. Q: How do I adjust the handle for left or right opening?
   A: To adjust the handle for left or right opening, follow these steps:

3. Move downward the handle at a 45-degree angle till you see the screws inside.

4. Unscrew the screws.

5. Move the handle 270 degrees backward till you see the screw holes.

6. Screw the screws back in.

7. Q: How deep should I drill the door frame holes for the strike plate?
   A: The door frame holes should be drilled at least 1/2 (12mm) deep.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>