DANCING 1.6M 1:5 S.E.5a Balsawood Scale Airplane Instruction Manual
- June 12, 2024
- DANCING
Table of Contents
- PRE-FLIGHT CHECKS
- SAFETY PRECAUTIONS
- Specification
- Assembly symbol guide
- Assemble the Landing Gear
- Assemble the Tail Wing and Tail Wheel
- Wing installation
- Installation of control servos for horizontal tail and vertical tail
- Install the motor and cowling
- Install the stay wire
- Set and Adjust
- Control Directions Tests
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
1.6M 1:5 S.E.5a Balsawood Scale Airplane
Instruction Manual
SCG42
ARF
PRE-FLIGHT CHECKS
- Check/adjust servo centering, in order to adjust the control surface better.
- Double-check the spinning direction of motor at first usage, and sure it’s suitable for your model.
- Set the center of gravity (CG) at the position that manual already marked out. If necessary, add weight to the nose or tail to ensure the best flight performance.
- Double-check the inside of the fuselage, make sure all the equipments are correctly connected; Check the heat-shrink covering material’s surface, Make certain all screws, bolts, cabin and canopy remain secure.
- Take great care when connecting/disconnecting the battery, pls replace the battery immediately once found low voltage or damage to battery.
- The way the internal devices of the fuselage are connected will be related to your transmitter-receiver device. For those transmitter-receiver devices with more functions, you can simplify the connection of the internal devices of the fuselage. Check your device for details to see if it meets the features you need.
- When the power system and transmitter-receiver device are paired for the first time, you may need to set the maximum stroke of the throttle. Please set it yourself.
SAFETY PRECAUTIONS
- This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A TOY.
- Do not fly around some restricted location like airports, military bases, residential areas, etc.
- You will need to range check the transmitter to be sure you are not experiencing any interference.
- Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.
- If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from advanced expert fliers.
- Keep relevant items out of reach of children.
- This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use, if you plan to perform any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body strength.
- This product may include some fiberglass and carbon-fiber reinforced plastic parts, which may cause eye and skin discomfort, pls wear the goggles or dust-proof clothes when needed.
- Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the glue you need at your local stationery store.
Specification
Wingspan:1.62M(63.8″)
Fuselage Length:1.25M(49.2″)
Fly weight:≈3.1kg
Suggested Equipment
Motor : 3520-4220 800-500KV
Prop : 14inch
ESC:60-80A(4S)
Battery:4S 2200-4000mAh
Servo : 17g*4pcs
Radio:4CH+
Tools Needed
SCG42-B: Upper Wing
SCG42-A: Fuselage
SCG42-C: Lower Wing
SCG42-D: Landing Gear
SCG42-E: Wing bracket
SCG42-F: Horizontal tail/Vertical tail
SCG42-J: screws & parts
SCG42-H: Dummy machine gun
Collimator
Exhaust pipe
SCG42-G: tail wheel set
K:PVC PVC window shield
SCG42-J: screws & parts Rudder horn Wood block; Wood rod Connecting rod Stay
wire
Assembly symbol guide
Assemble the Landing Gear
Assemble the Tail Wing and Tail Wheel
Wing installation
Installation of dummy parts
Note: The upper and lower wing control surfaces shall be installed according to steps 03-9 and 03-10, and the left and right wing control surfaces shall be installed the same.
Installation of control servos for horizontal tail and vertical tail
Install the servo at the servo position shown in the figure, install the EZ- connecor on the rudder arm, install the control horn at the reserved hole of elevator and rudder, and connect the servo and control horn with steel wire connecting rod.
Install the motor and cowling
In combination with steps 05-4 and 05-6, adjust the position of the motor base
according to the size of the motor, and then use epoxy adhesive to fix the
motor base.
Install the propller and fix with adapter.
Note: The motor base has been designed with right pull and pull down
angles.
Install the stay wire
Installation of dummy parts
Set and Adjust
Display the C.G
Usually, the control throws set as below:
(Normal Flying)
Aileron ±(15°-30°)
Elevator ±15°
Rudder ±15°
Flap (take-off)15°-20°
(3D Flying only support some models)
±40° (or larger)
±40° (or larger)
±40° (or larger)
(Landing)20°-40°
Some special models will have V-tails, flaps, leading edge wings, etc., which
can be used as a reference for conventional flight angles. If you do not
confirm and there is no experienced person to guide you, we recommend that you
first test at a small angle to confirm that your settings are correct.
Control Directions Tests
| Transmitter Command| Aircraft Reaction
---|---|---
Elevator| Lifting rod down|
Lifting rod up|
Aileron| Steering rod to the right|
Steering rod to the left|
Rudder| Direction rod to the right|
Direction rod to the left|
More details about power system adjustment, please refer to below link: (You
can scan QR Code directly.)
http://www.dwhobby.com/art/connection
References
- DancingWingsHobby AEOrc ELErc HOBBY, RC PLANE,Balsawood Airplane,EPP Foamy Plane,BRUSHLESS MOTOR ,EDF,BLADE,PROPELLER
- How to Connect
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>