VACOS B09NW1NQSS Video and Audio Camera Baby Monitor User Manual

Baby Monitor
User Manual

What’s in the Box

Note: The power adapters may vary based on the specific countries’ adapter specifications.

Product Description

LCD Monitor Introduction

Camera Introduction

How to Set up the Camera and Monitor

Power on the Monitor
Note: Please fully charge the monitor before operation.

1. Connect one end of the power cable to the 5V/2A power adapter, and then link the other end of the power cable (the Type-C end) to the monitor.
2. Plug the power adapter into the outlet.
3. Press the power button for 3 seconds to turn on the monitor.

Power on the Camera

1. Connect one end of the power cable to the 5V/1A power adapter, and then link the other end of the power cable (the Type-C end) to the camera.
2. Plug the power adapter into the outlet.

Positioning
Place the camera at somewhere near the crib, such as on the cabinet, so you can monitor your baby conveniently.
Note: NEVER place the camera or cords within 3-feet of the crib. Caution:
Never place the camera inside or mount the camera on baby’s bed/playpen, avoiding accidentally falling off or being entangled by wires. Keep the camera out of baby’s reach, at least 3 feet away from the crib and the baby. Place the camera on a stable and leveled surface. Adjust camera’s lens to ensure the best visibility of your child.

How to Add the Camera to the LCD Monitor

The monitor and camera have been paired by default. If you want to add a new camera to the monitor, or the camera is reset, you’ll need to pair them again. Please refer to the following steps to pair the monitor and camera.

1. Press the Menu ( ) icon button to enter the main menu, and then press up/down ( ) icon button to select the system setting. Press the OK ( OK ) icon button.
2. Use the up/down ( ) icon button to select pairing, and then press OK to go to the camera pairing interface. Select the camera you want to pair and press the ( OK ) icon button.
3. The interface shows a countdown to the pairing.
4. Tap the pairing button for 1 second until you hear a tone that the pairing is complete.

Note: The pairing button is on the back of the camera.

Switch the Cameras via the LCD Monitor

You can switch the cameras manually if you have added more than 2 cameras to the monitor. The monitor can show up to 4 cameras’ stream simultaneously.
Note: The monitor may make a loud noise if the monitor is too close to the camera.
The problem can be solved once the monitor is away from the camera.

How to Install the Camera to the Wall

1. Place the bracket on the wall, and then mark the positions on the wall.

2. Drill holes at the marked positions, and put anchors into the holes.
   Note: Anchors are not needed in the wooden wall.

3. Fix the bracket to the wall with the screws.

4. Install the camera into the bracket.

Baby Monitor Setting Menu

Press the power ( ) icon button to turn on the monitor, and then press menu button to go to the setting menu. Setting Menu Introduction

off the lullaby.
Note: The sound alert will be automatically turned off when lullabies are being played.
Warning: You may not hear the baby’s crying sound when playing the lullaby.
| You can set up the sound sensitivity. When the camera detects any specific noise, the monitor will display the icon and alert you audibly.
Note: The ambient noise may cause false alerts.
| You can set up the temperature detecting range. When the temperature exceeds the specific value, the monitor will display the icon and alert you audibly.
| Set up the alarm clock
| You can choose the auto-lock screen time for your monitor among 1, 2 and 5 minutes.
| Record Setting| Description
---|---|---
Playback| View recorded video clips
Motion Detect| Turn on/off the motion detection alerts
Recording Time| Set up the single recording time
Overwrite| Select ” On ” , the TF card will be full , and the oldest video will be deleted while recording . Select ” Off ” , and the TF card will not record when it is full .
Format| Format the TF card
Note: Format the TF card when you install the TF card to the camera for the first time.
Card Info| The storage capacity of the TF card
| System Setting| Description
---|---|---
Date Time| Set up the date and time on the monitor
Pairing| Add a camera
Note: 1 monitor supports up to 4 cameras.
Frequency&WiFi| Frequency: Change the refresh rate of the device to prevent flicker.
Region: WiFi channels can be set to boost signal connectivity
Alert Volume| Set up the alert volume
Language| Set up the menu language
Default| Restore all settings to default
Firmware Update| The version information and update settings of the software
Image Flip| Image FIip:According to the Installation direction of the camera,choose whether to flip the image
Night Vision Mode :Day and night mode changeover can be set manually

Note: The interval between every two audible alerts is 10 seconds. During the 10-second time interval, the device won’t send you notifications even there are motion events.

Introduction to Live Stream

device is recording when the icon flashes red and white alternatively.
| Camera volume
| Playing the lullaby
| The VOX is on. The white icon shows VOX is on. There will be audible alerts when there are motion events. The icon will flash red and white alternatively for 10 seconds, and then the icon turns white.
| Sleep mode
| Motion detection function: The white icon shows motion detect is on. When the camera detects motions, the icon turns red and you will hear a prompt tone. The red icon will turn white in 10 seconds.
| TF card: The white icon shows TF Card has been inserted, while the red icon shows the card storage is full.
| The monitor’s image magnification
| Temperature detect: The red icon shows the temperature surpasses the specified line, and you will hear a prompt tone.
| Feeding timer: You’ll see a red alarm icon on the monitor screen after you have enabled the camera volume, and hear a voice prompt when the countdown ends.
| Remaining power of battery
| Long press the Talk button on the monitor and this icon will display on the monitor screen.
| In a standalone live stream, you can rotate the camera up & down, left & right by controlling the direction button on the monitor.
| In acertain single monitoring screen, press the submenu button to use the up/down button to adjust the brightness,
the left/right button to adjust the sound volume. Press OK button to record manually.
| In the multi-screen mode, the monitor will display the select box. When the select box displays in the camera stream in the top right corner, it means that you have selected the camera, and the voice is from the camera.
Please press the Menu button to get the settings of the camera. Control the up/down/left/right direction to change the select box. After you have pressed OK button, you can switch to the current camera’s stream with the select box

FAQ

Q: How to power on/off & turn on/off the LCD monitor?

A: Power on/off the monitor: Press the power button for 5 seconds; Turn on/off the monitor: Press the power button once.

Q: What's the connection distance between the camera and monitor?

A: The longest connection distance between the camera and LCD monitor is 1,000 feet in open areas without interference.

Q: Why does the baby monitor record videos without human - triggered events ?

A: When the motion detection function is enabled , the baby monitor will start recording whenever it detects the scene changes ( such as the oscillating fan. fluttering curtain , or swaying trees ) .

Q: Why does the display turn on automatically after turned off?

A: The display will turn on when the Power button is pressed, or when alarms of audio, motion, temperature, and feed time clock are activated.

Q: When the device in different scenes because of obstacles and signal interference and other reasons video delay, poor signal, how to avoid interference?

A: Can be based on different regional signal regulations and 14 channels for customers to choose, FCC, EU, MKK, Other (Turbo) .

Q: How can | avoid switching back and forth between black and white/color when the camera is backlit or in a complex lighting environment?

A: You can go to the Image Setting-Night Vision Mode option in the device menu to select the appropriate image mode according to the light and brightness of the camera, Auto, Day Mode, Night Mode.

Shenzhen Kean Digital Co., Ltd.
Address: Room 1001, Rujun Building, No.105 Center Road,
Bantian Street, Longgang District, Shenzhen, 518129, China.
support@vacos.com 
vacos.com
MONITOR FCCID: 2AKL2K52LED
CAM FCCID: 2AKL2K62CAM
Made in China THEMIS AR Unterstutzung UG
Beedstrasse 54, In Dusseldorf, (40468), Deutschland

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>