VACOS 20210913 1080p Full HD Wireless Smart IP Security Camera User Manual

Vaco’s Indoor Camera
USER MANUAL

About This Manual
The Manual includes instructions for using and managing the product. Pictures, charts, images, and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version on the company website. Please use this user manual under the guidance of professionals.
Legal Disclaimer
REGARDING THE PRODUCT WITH INTERNET ACCESS, THE USE OF THE PRODUCT SHALL BE WHOLLY AT YOUR OWN RISK. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITY FOR ABNORMAL OPERATION, PRIVACY LEAKAGE, OR OTHER DAMAGES RESULTING FROM CYBER ATTACKS, HACKER ATTACKS, VIRUS INSPECTIONS, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED FOR ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.

Regulatory Information

FCC Information

FCC compliance:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. RF Exposure Warning Statements: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with a minimum distance of 20cm between the radiator & body.
EU Conformity Statement
This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info
Safety Instruction

These instructions are intended to ensure that users can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may occur if any of the warnings are neglected.

Cautions: Injury or equipment damage may occur if any of the cautions are neglected.

| Warnings Follow these safeguards to prevent serious injury or death.
---|---
| Cautions Follow these precautions to prevent potential injury or material damage.

Warnings

• Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
• In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
• Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
• In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
• Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 100-240 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
• Do not connect several devices to one power adapter as adapter overload may cause overheating or a fire hazard.
• Please make sure that the plug is firmly connected to the power socket.
• If smoke, odor, or noise rises from the device, turn off the power at once and unplug the power cable, and then please contact the service center.

Cautions

• Do not drop the camera or subject it to physical shock.
• Devices are designed for indoor use only. Keep them away from liquids and humid environments.
• While in delivery, the camera shall be packed in its original packing, or packing of the same texture.
• A few parts(e.g.electrolytic capacitor) of the devices shall be replaced regularly according to their average enduring time. Please check their conditions regularly and replace them in time.
• Use only attachments/accessories specified by the manufacturer.
• Improper use or replacement of the battery may result in a hazard of explosion. Replace with the same or equivalent type only. Dispose of the waste batteries according to the instructions provided by the battery manufacturer.
• If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. )

Preventive and Cautionary Tips
Before connecting and operating your device, please be advised of the following tips:

• Make sure the power supply voltage is correct before using the camera.
• Install the system in a well-ventilated, dust-free environment.
• Do not place the camera in extremely hot, cold (the operation temperature shall be 0 C ‘— 4 0 C, storage temperature shall be -2 0 C — 6 0 C), dusty or damp locations, and do not expose it to high electromagnetic radiation.
• Place the devices on stable and leveled surfaces, avoiding falling down or dropping.
• Use the device in conjunction with an uninterrupted power supply if possible.
• Only clean the devices with a dry cloth; never use chemical cleaners. Before any cleaning, you must disconnect the adapters.
• Power down the device before connecting and disconnecting accessories and peripherals.
• Unplug this device when unused for long periods of time.

What in the box

Product Description

Reset Button/Indicator Light| Operation/Light Status| Description
---|---|---
Reset Button| Long Press| Reset the Camera
Indicator Light| Solid Red Light| Device Initiation or Device Error
Slow Flashing Red Light| Ready for WiFi Connection
Fast Flashing Red Light| WiFi Connecting
Solid Blue Light| WiFi Connected

Product Description

3.1 Ensure your router supports the 2.4 GHz wireless network and DHCP.
The camera is only compatible with the 2.4 GHz wireless network.
3.2 Ensure your router is encrypted by WAP/WAP2, and there are no special characters in the username and password of your WiFi login account.
3.3 Ensure your WiFi is working properly, and your phones or tablets have been connected to the WiFi.
3.4 Search for Vaco’s Smart in App Store or Google Play. Download and install it on your phones or tablets.

Create Your Vacos Account

New users need to sign up by email/phone number. Click Sign Up, follow the steps to complete the registration, and then log in. (Photo 1, 2, 3)

Add the Device

5.1 Tap the add-device icon “ ” on the screen, and select Indoor Camera in the device list. Plug the camera into a power outlet, and tap Next. (Photo 4, 5, 6) 5.2 Follow the instructions on the screen to reset your device, and then tap Next. (Photo 7)
5.3 Enter the WiFi password, and then tap Next. (Photo 8)

5.4 A QR code will be shown on your phone. Please scan the QR code with the camera. (Photo 9, 1 0)
Note: To ensure the camera can scan the QR code successfully, please turn off the Auto-Lock function of your phone. Ensure the camera and QR code are in the same horizontal line, and the operating environment is bright enough. If the scan fails, please request a video guide by email from our tech support at support@vacos.com.

5.5 You’ll hear a prompt tone when the scan is completed. Tap Next on the app. You will hear a prompt tone indicating WiFi connecting. When the app screen shows 100% connecting, the Indoor camera has been connected to your WiFi. (Photo 10)
Note: If the camera fails to connect to the WiFi, please reset the camera and try again.
5.6 You can name your camera when the camera is online, and then tap Done. (Photo 11)
5.7 Now enjoy your live stream. (Photo 12)

Install the Camera to the Wall

6.1 Place the bracket on the wall, and then mark the positions on the wall.
6.2 Drill holes at the marked positions, and put anchors into the holes.
Note: Anchors are not needed for the wooden wall.

6.3 Fix the bracket to the wall with screws.

6.3 Install the camera into the bracket.

 Troubleshooting

Q: Why can’t I get the live stream?
A: Please check the WiFi connection. You can put the camera close to the router to check if your device can connect to WiFi. If the issue still exists, please reset your device and try again.
Q: Why is the camera still in the device list after it’s reset?
A: Device resetting only resets the network configuration of the camera, and doesn’t change the configurations of the app. If you want to remove the camera, please delete it from the device list manually in the app.
Q: Why can’t my camera recognize a microSD card?
A: Ensure your microSD card meets the standards. The supported microSD card format is FAT32. You are advised to insert a microSD card when the camera is powered off. The camera can’t recognize a microSD card with a poor network connection.
Q: Why can’t I receive app notifications?
A: Ensure the app is running on your phone first. To get notifications, you should enable the notification in the app and allow the Vacos Smart App notification in your smartphone’s settings.

Shenzhen Kean Digital Co., Ltd.
Address: Room 1001, Rujun Building, No.105 Center Road,
Bantian Street Longgang District, Shenzhen, 518129, China.
support@vacos.com 1 vacos.com
FCC ID: 2AKL2K22IPC I Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>