VACOS Indoor Cam PT User Manual
- June 10, 2024
- VACOS
Table of Contents
VACOS Indoor Cam PT
User Manual
Indoor Cam PT
About This Manual
The Manual includes instructions for using and managing the product. Pictures,
charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to change
, without notice, due to firmware updates or other reasons. Please find the
latest version in the company website .
Please use this user manual under the guidance of professionals.
Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE
CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT
THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS
BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the
limits for a Class 8 digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Warning Statements: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
EU Conformity Statement
This product and – if applicable – the supplied accessories too are
marked with “CE” and comply therefore with the applicable harmonized European
standards listed under the EMC Directive 2004/108/EC, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European Union. See
the product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information see:
www.recyclethis.info
Safety Instruction
These instructions are intended to ensure that user can use the product
correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions” Warnings:
Serious injury or death may occur if any of the warnings are neglected.
Warnings Follow these safeguards Cautions Follow these precautions to to
prevent serious injury or death. prevent potential injury or material damage.|
Cautions: Injury or equipment damage may occur if any of the cautions are
neglected.
---|---
Warnings
-
Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
-
In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
-
Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
-
In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
-
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 100~240 VAC or 12 VDC according to the IEC60950-1 standard.
Please refer to technical specifications for detailed information. -
Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard.
-
Please make sure that the plug is firmly connected to the power socket.
-
lf smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
Cautions
- Do not drop the camera or subject it to physical shock.
- Devices are designed for indoor use only. Keep them away from liquids and humid environments.
- While in delivery, the camera shall be packed in its original packing, or packing of the same texture.
- few parts(e.g.electrolytic capacitor) of the devices shall be replaced regularly according to their average enduring time. Please check their conditions regularly and replace therm in time.
- Use only attachments/accessories specified by the manufacturer.
- Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose the waste batteries according to the instructions provided by the battery manufacturer.
- If the product does not work properly , please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. )
Preventive and Cautionary Tips
Before connecting and operating your device , please be advised of the
following tips:
Make sure the power supply voltage is correct before using the camera.
Install the system in a well-ventilated, dust-free environment.
-
Do not place the camera in extremely hot, cold (the operation temperature shall be 0C~40C, storage temperature shall be – 20 C ~ 60 C), dusty or damp locations, and do not expose it to high electromag netic radiation.
-
Place the devices on stable and leveled surfaces, avoiding falling down or dropping.
Use the device in conjunction with an uninterrupted power supply if possible. -
Only clean the devices with a dry cloth; never use chemical cleaners. Before any cleaning, you must disconnect the adapters.
Power down the device before connecting and disconnecting accessories and peripherals. -
Unplug this device when unused for long periods of time.
What’s in the Box
Product Description
Reset Button/Indicator Light| Operation/Light Status|
Description
---|---|---
Reset Button| Press Once| Activate One-Touch Call
Long Press| Reset the Camera
Indicator Light| Solid Red Light| Device Initiation or Device Error
Slow Flashing Red Light| Ready for WiFi Connection
Fast Flashing Red Light| WiFi Connecting
Solid Blue Light| WiFi Connected
Product Description
3.1 Ensure your router supports the 2.4 GHz wireless network and DHCP. The
camera is only compatible with the 2.4 GHz wireless network.
3.2 Ensure your router is encrypted by WAP/WAP2, and there are no special
characters in the username and password of your WiFi login account.
3.3 Ensure your WiFi is working properly, and your phones or tablets have been
connected to the WiFi.
3.4 Search for Vacos Smart in App Store or Google Play. Download and install
it into your phones or tablets.
Create Your Vacos Account
New users need to sign up by email/phone number. Click Sign Up, follow the steps to complete the registration, and then log in. (Photo 1, 2, 3)
Add the Device
5.1 Tap the add-device icon “ + “on the screen, and select PT Camera in the
device list.
Plug the camera into a power outlet, and tap Next. (Photo 4, 5, 6)
5.2 Follow the instructions on the screen to reset your device, and then tap N
xt. (Photo 7)
5.3 Enter the WiFi password, and then tap Next. (Photo 8)
5.4 A QR code will be shown on your phone. Please scan the QR code with the
camera. (Photo 9, 10)
Note: To ensure the camera can scan QR code successfully, please turn off
the Auto-Lock function of your phone.
Ensure the camera and QR code are in the same horizontal line, and the
operating environment is bright enough. If the scan fails, please request a
video guide by emails from
our tech support at support@vacos.com.
5.5 You’ll hear a prompt tone when the scan completed. Tap Next on the app.
You will hear a prompt tone indicating WiFi connecting. When the app screen
shows 100%
connecting, the PT camera has been connected to your WiFi. (Photo 10)
Note: If the camera fails to connect the WiFi, please reset the camera
and try again.
5.6 You can name your camera when the camera is online, and then tap Done.
(Photo 11)
5.7 Now enjoy your live stream. (Photo 12)
Install the Camera to the Wall
6.1 Place the bracket on the wall, and then mark the positions on the wall.
6.2 Drill holes at the marked positions, and put anchors into the holes.
Note: Anchors are not needed for the wooden wall.
6.3 Fix the bracket to the wall with screws
6.4 Install the camera into the bracket
Troubleshooting
Q: Why can’t I get the live stream?
– A: Please check the WiFi connection. You can put the camera close to the
router to check if your device can connect to WiFi. If the issue still exits,
please reset your device and try again.
Q: Why is the camera still in the device list after it’s reset?
– A: Device resetting only resets the network configuration of the camera,
and doesn’t change the configurations of the app. If you want to remove the
camera, please delete it
from the device list manually in the app.
Q: Why can’t my camera recognize a microSD card?
– A: Ensure your microSD card meets the standards. The supported microSD
card format is FAT32. You are advised to insert a microSD card when the camera
is powered off. The camera can’t recognize a microSD card with poor network
connection.
Q: Why can’t I receive app notifications?
– A: Ensure the app is running on your phone first. To get notifications,
you should enable the notification in the app and allow the Vacos Smart App
notification in your
smartphone’’s settings.
Shenzhen Kean Digital Co., Ltd.
Address: Room 1001, Rujun Building, No.105 Center Road,
Bantian Street, Longgang District, Shenzhen, 518129, China.
Support@vacos.com | vacos.com
FCC ID: 2AKL2K22IPC | Made in China
THEMIS AR Unterstutzung UG
Beedstrasse 54, In Dusseldorf, (40468), Deutschland
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>