levoit LV6S Smart Hybrid Ultrasonic Humidifier User Manual

**levoit LV6S Smart Hybrid Ultrasonic Humidifier User Manual

**

Package Contents

• 1x Smart Hybrid Ultrasonic Humidifier
• 3x Aroma Pad (1 Pre-Installed)
• 3x Absorption Pad (1 Pre-Installed)
• 2x Water Filter Sponge (1 Pre-Installed)
• 1x Cleaning Brush
• 1x User Manual
• 1x Quick Start Guide

Bonus Items

1x Remote Control
1x 3V CR2025 Battery (Pre-Installed)

Specifications

Note : The humidifier may run for a longer or shorter time depending on the environmental temperature and humidity.

Noise Level| 430-753 ft²/40-70 m²
Effective Range| 11.5 x 7.6 x 11.2 in /
Dimensions| 29.2 x 19.3 x 28.8 cm
Weight| 5.6 lb/2.6 kg

Note: To access additional smart humidifier functions, download the free VeSync app (see page 1.

READ AND SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

To reduce the risk of fire, electric shock, or other injury, follow all instructions and safety guidelines.

General Safety

• Only use the humidifier as described in this manual
• Place the humidifier and cord so that it will not be knocked over. Do not place near large pieces of furniture or in high- traffic areas.
• When not in use, turn the humidifier off and disconnect from power by removing the plug from the outlet
• Do not use the humidifier in wet environments.
• Keep the humidifier out of reach from children.
• Do not open the base or remove the water level sensor for self-servicing
• Always unplug your humidifier from the power outlet before cleaning or detaching the water tank from the humidifier base.
• Always make sure to place the humidifie on flat, level surface before operation.
• Only fill the water tank with clean water. Never fill the water tank with any other liquids
• Do not place the humidifier near sources of heat, such as stovetops, ovens, or radiators.
• Do not place the humidifier directly on floors, carpets, of rugs.
• Do not use other items as replacement parts for this product
• Do not cover the nozzles while the humidifier is on. Doing so may damage the humidifier.
• Remove the water tank from the base before moving the humidifier.
• Do not immerse the humidifier base, power cord, or plug in water.
• Do not clean the humidifier immediately after turning it off, especially if it has been diffusing warm mist
• Allow the humidifier to cool down completely before cleaning
• If the humidifier is damaged or s not functioning properly, stop using it and contact Customer Support immediately (see page 29)
• This humidifier is not to be used by persons (including children) with reduced physical, sensory, or mental capabiliies, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Supervise children when they are near the humidifier.
• Children should not clean or perform maintenance on the humidifier without supervision
• Children should be supervised to ensure that they do not play with the humidifier.
• Not for commercial use. Household use only.

Caution: Risk of Leaks and Electric Shock

• Do not add essential o, supplemental water treatment liquids, or water filters into the water tank or base chamber. This will damage the humidifier and cause leaks. Only add essential olls to the aroma pad.

Power & Cord 

• Ensure that the plug fits properly into a polarized socket
• Do not handle the power cord or plug with wet hands. Keep the plug and power cord away from liquids.
• Your humidifier has a polarized plug (one prong is wider than the other), which fits into a polarized outlet only one way. This is a safety feature to reduce the risk of electric shock. Ifthe plug does not fit, reverse the plug. If it sill does not fit, do not use the plug in that outlet. Do not bypass this safety feature.
• Ifthe power supply cord is damaged, it must be replaced by Arovast Corporation or similarly qualified persons in order to avoid an electric or fire hazard. Please contact Customer Support (see page 29)
• Unplugging the power cord will disable remote control of the humidifier and temporarily disconnect the humidifier from VeSync and other third-party apps.

This product contains a coin/button battery.

WARNING: CHEMICAL BURN HAZARD. KEEP OUT OF REACH OF CHILDREN.

Swallowing can lead to chemical burns, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion Seek medical attention immediately.

• Dispose of the battery immediately according to local regulations;
• Store spare batteries securely;
• Use non-transparent containers to keep the batteries out of view.

Unfortunately, it is not obvious when a button or coin battery is stuck in a child’s esophagus (food pipe). The child might

• Cough, gag or drool a lot;
• Appear to have a stomach upset or a virus;
• Besick;
• Pointto their throat or stomach;
• Have a pain in their abdomen, chest or throat;
• Be tired or lethargic;
• Be quieter or more clingy than usual or otherwise “not themselves”;
• Lose their appetite or have a reduced appetite;
• Notwant to eat solid food / be unable to eat solid food.

These sorts of symptoms vary or fluctuate, with the pain increasing and then subsiding.

A specific symptom to button and coin battery ingestion is vomiting fresh (bright red) blood. If the child does this seek immediate medical help.

The lack of clear symptoms is why it is important to be vigilant with “flat” or spare button or coin batteries in the home and the products that contain them. Be aware that even used button or coin batteries may cause injury

Electromagnetic Fields (EMF)

This humidifier complies with all standards regarding electromagnetic fields (EMF)

If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today,

GETTING TO KNOW YOUR SMART HUMIDIFIER

Function Diagram

• A. Nozzles
• B. Top Cover
• C. Handle
• D. Water Tank
• E. Water Filter
• F. Water Filter Sponge
• G. Base
• H. LED Display
• I. Control Panel
• J. Aroma Box
• K. Aroma Pad
• L. Humidity Sensor (In Aroma Box Compartment)
• M. Mist Tube
• N. Mist Channel
• O. Noise Silencer
• P. Absorption Pad
• Q. Air Outlet
• R. Float Brackets
• S. Base Chamber
• T. Power Cord
• U. Water Outlet Valve
• V. Heating Element
• W. Transducer
• X. Float
• Y. Remote Control

Indicators

• A. Sleep Mode Indicator
• B. Timer Indicator
• C. WiFi® Indicator
• D. No Water Indicator
• E. Relative Humidity (RH) Percentage
• F. Warm Mist Setting Indicator
• G. Mist Level Indicator

Buttons

• H. On/Off Button
• I. Mist Level Button
• J. Humidity Level Button
• K. Warm Mist Button

Mist Level Indicator (Blue)

Warm Mist Indicator (Orange)

CONTROLS & DISPLAY

Note: You can also use the VeSync app to control these functions, as well as additional app-only features (see page 16). These controls are also on the included remote control.

On/Off Button

• Tap to tum the humidifier on/oft
• Press and hold for 5 seconds to pair with the VeSync app. See the VeSync in-app instructions for more information.
• Press and hold for 15 seconds to reset the humidifier. This will restore the humidifier’s default settings and disconnect it from Wi-Fi® and the VeSync app (see page 1)

Mist Level Button

• Tap repeatedly to cycle through mist level settings: low, medium, and high mist.
• Press and hold for 3 seconds to tur the display off Tap any button to turn the display back on
• To turn display off: Press and hold § for 3 seconds. Tap any button to tum the display back on

Humidity Level Button

• Sets the relative humidity (RH) percentage. The humidifier will automatically stop misting when the room reaches the target humidity level (see page 13)
• Press and hold for 2 seconds to cancel your humidity level setting.

Warm Mist Button

• Cycles through warm mist settings: low heat, medium heat, high heat, and heat off (see page 13)

Wi-Fi Indicator

• Tumns on, off, or blinks to indicate pairing status. See the VeSync in-app instructions for more information.

No Water Indicator

• Blinks when there is no water in the tank. After this indicator blinks 10 times, the humidifier will turn off. Refill the tank and properly place it on the base to use your humidifier.
• Lights up when the water tank is removed. Remains on until the tank is replaced.

Remote Control
The remote control can be used to control any of the humidifier’s functions from a distance. It must be within 16 /5 m of the humidifier to work.

Note:

• Remove the plastic tab from the remote control’s battery compartment before using.
• Tore place the battery, see page 20.

Timer Button

• Sets or cancels a timer (see page 14)
• Can only be controlled through the remote control or VeSync app.

Sleep Mode Button

• Press to tum Sleep Mode on/off (see page 14).
• Can only be controlled through the remote control or VeSync app.

GETTING STARTED

1. Remove all packaging

2. Clean the water tank and water tank cover before first use.
   Note: Check to make sure that the water filter is correctly in place. If not, then rotate the filter clockwise to secure itin place.

3. Choose a hard, flat location for the humidifier at least 12 inches /30 cm away from any walls. The surface must be water-resistant. [Figure 11]

   • Do not place the humidifier directly on floors, carpets, or rugs.

4. Mistshould be directed away from walls, fumiture, bedding, and appliances. Avoid letting too much mist fall on the side of the humidifier with the aroma box, as this may interfere with the sensor inside the aroma box

Note: The humidity sensor and an air inlet are both focated inside the aroma box. Placing the humidifier away from walls will also ensure that the inlet and sensor function properly.

FILLING & REFILLING

Note: Make sure the water tank is clean

1. Remove the water tank cover.
2. Use the handle to remove the tank from the base. Fill the tank with room- temperature water. Do not fill with hot water.
3. Replace the water tank cover and place the tank back on the base. [Figure 2]
   

Note:

• We recommend using purified water to fil the tank.
• Using tap water may result in a white dust (dried minerals) on surfaces.

Caution

Do not add water directly into the base chamber. [Figure 2.2]

Do not add water through the misttube. [Figure 2.3]

Do not add essential oils into the humidifier. Only add essentic oils to the aroma pad. [Figure 2.4]

Do not use water treatment liquids or third-party water filters in this humidifier [Figure 2.5]

VESYNC APP SETUP

Note: Due to ongoing updates and improvements, the VeSync app may be slightly different than shown in the manual. In case of any differences, follow the in-app instructions.

1. To download the VeSync app, scan the QR code or search “VeSync” in the Apple App Store® or Google Play Store.
   Note: For Android” users, choose Allow to use VeSync.
   
   
   [ **](https://play.google.com/store/apps/details?id=com.etekcity.vesyncplatform&hl=en)
   **

2. Open the VeSync app. If you already have an account, tap Log In. To create a new accourt, tap Sign Up.
   Note: You must create your own VeSync account to use third-party services and products. These wil not work with a guest account With a VeSync account, you can also allow your family and friends to control your smart humidifier

Wi-Fi Connection

1. To disconnect Wi-Fi, press and hold for 15 seconds until the Wi-Fi indicator turns off. This will restore the smart humidifier’s default settings and disconnect it from the VeSync app.
2. Toreconnect, please follow the instructions in the VeSync app for adding a device.
3. Follow the in-app instructions to set up your smart humidifier.

Note:

• You can use the VeSync app to connect your smart humidifier to Amazon Alexa or Google Assistant”. Follow the in-app instructions to connect VeSync to your voice assistant.
• Your phone must have Location tumed on while your phone is connecting to Yyour smart humidifier. This srequired to establish the Bluetooth® connection. You can turn Location off after your smart humidifier is finished connecting to the VeSync app.

USING YOUR SMART HUMIDIFIER

Note: Using the VeSync app allows you to control your smart humidifier remotely and access additional functions and features (see page 16).

1. Plug in the humidifier. The humidifier wil light up, then tum off

2. Tap to turn your humidifier on. The humidifier will start misting
   Note: Ifthere is no water in the tank, will flash 10 tmes, and the humidifier wil tum off Fil the water tank (see Getting Started, page 9.

3. Tap$ repeatedly to cycle through mist settings: Low, Medium, and High

4. Rotate the nozzles to adjust the direction of the mist. **[Figure 31]

Note:

**

  * Direct the nozzles away from any furniture, walls, or other objects to prevent them from getting wet.
  * Do not inhale the mist directly from the nozzles.

5. Optionally, use the controls or the VeSync app to turn on warm mist, activate Sleep Mode, and more (see Controls & Display, page 8)

6. When your room has reached your preferred humidify level, tum the humidifier to a lower setting, or tum it off. A comfortable humidity level is between 40% and 60%
   Note: You can also set the humidifier to automatically stop misting when the room reaches a specific humidity level (see Humidity Level, page 13).

7. Tap  to tumn your humidifier off.

Warm Mist

• Tap tout on warm mist. Keep tapping to increase the heat setting for the mist, and to turn warm mist off.
• Caution: Mist may be hot. Do not place your bare hands, face, or other exposed skin over the nozzles while using warm mist [Figure 3.2]
• The humidifier may take 15 minutes to warm up before producing warm mist.
• The warm mist function can be used during Sleep Mode.

Humidity Level

You can customize the humidity leve that the humidifier will maintain. The humidifier will automatically stop misting when the room reaches the target humidity level

1. Tap repeatedly to set a humidity level between 40% and 80% Relative Humidity (RH)

2. The display will flash 3 times to confirm your selection, then return to showing the current humidity percentage in the room
   Note:
   

   • The humidifier will automaticatly mist for 15 seconds after being turned on, even if the room has reached the set humidity level
   • Tap  ****once tosee the selected humidity level again. Keep tapping  to change the humidity level.
   • You can stil adjust the mist fevel, the timer, and the warm mist setting after setting the humidity level.
   • The humidifier will not increase the mist level when @ humidity level percentage is set, only stop misting once the set humidity level is reached. If you want the humidity in your room to increase faster, set the humidifier to high mist level.

3. Once the humidity of the environment reaches the humidity you set, the humidifier will automatically stop misting.

4. The humidifier will continue detecting the humidity level in the room. It will start misting again when the humidity drops to 5% below the set level

Note:

• To cancel the set humidity level, press and hold for 2 seconds, which will set the humidity level to “. The display will lash 3 times to confirm, then return to showing the current humidity percentage in the room.
• When the humidity level is set to “* the humidifier will automatically keep misting at the current mist level until it runs out of water

Timer

You can set an auto-shutoff timer between 1and 12 hours.

• Press repeatedly on the remote control to choose a time in increments of 1 hour. When you stop pressing , the display will flash 3 times and the timer will start.
• The humidifier will automatically power off once the timer is finished.
• To cancel a timer, press and hold for 3 seconds. You can also press repeatedly until the display reads *~ or use the VeSync app.

Note: Timer can only be controlled through the remote control or VeSync app.

Sleep Mode

Sleep Mode changes the humidifiers mist setting to an automatic mode and tumns off the display lights.

• Press on the remote control to turn Sleep Mode on/off.
• Sleep Mode automatically turns off warm mist to reduce noise. You can press ( toturn warm mist back on.
• Sleep Mode uses the humidity sensor to detect the relative humidity in the room and automatically adjusts the mist level to maintain 50-60% relative humidity.

Note: Sleep Mode can only be controlled through the remote control or VeSync app.

• When Sleep Mode s on, you can tap or press any button to wake up the display. If you stop touching the display, the display will tum off again after 6 seconds.
• When Sleep Mode s on, you can use all other settings except changing the mist level or humidity level. I you change the mist level or humidity level, Sleep Mode will turn off.
• When Sleep Mode is turned on, the humidifier will automatically mist for 15 seconds, even if the room’s humidity level is over 60%

Turning Off the Display

The display will automatically dim after 30 seconds of inactivity.

• To tum off the display, press and hold  for 3seconds.
• To turn the display back on, tap any button
• You can alsopress % on the remote control to turn the display on/oft. [Figure 3.3]
  

Using the Aroma Box

Your humidifier can be used for aromatherapy.

1. Push the aroma box at the back of the base and pull it out. [Figures 3.4]

2. Put8-10 drops of essential oils on the aroma pad. [Figure 3.5]
   

3. Place the aroma box back into the humidifier.

4. Turn on the humidifier. The humidifier will automatically diffuse aroma when used

Note:

• Do not add resented olls, water treatment liquids, or third-party water filters into the water tank or base chamber. Only add essential oils to the aroma pad. [Figure 3.6]
• The aroma pads can be cleaned and reused after diffusing essential oils (see Cleaning the Aroma Pad, page 20)
• This humidifier uses a small heat-based aroma diffuser. The aroma fs intended to be light

Absorption Pads

The mineral absorption pads help reduce mineral buildup (scale) inside the humidifier, especially on the heating element

Note: For information on replacement aroma pads or absorption pads, see page 20.

Memory Function

• The humidifier will remember your settings for Mist Level, Humidity Level, Warm Mist, and Wi-Fi settings when tumed off or unplugged, and will resume those settings when turned back on.
• The humidifier will not remember Sleep or Timer settings, and the display will automatically turn back on when the humidifier is turned back on.

Automatic Shutoff

The humidifier will automatically tum off when all of the water in the tank has been diffused. will show on the display and blink 10 times before the humidifier turns off.Fill the water tank (see Getting Started, page 9).

If the tank has been removed from the base, the humidifier will automatically stop misting. will show on the display, and will turn off once the tank is placed properly back on the base.

VeSync App Functions

The VeSync app allows you to access additional smart functions, including those listed below

Remote Control From Your Phone

• Tum the humidifier on/off.
• Cycle through mist levels and heat levels, and tum Sleep Mode on/off.
• Tum the display lights on/off.

Monitor Humidity Levels

• Check current humidity levels in the humidifier’s environment

Set Timers & Schedules

• Program individual timers or create a schedule for your smart humidifier.

Third-Party Voice Control

• Compatible with Amazon Alexa and Google Assistant” for voice commands.

Note: The VeSync app s continually updated and app features will expand

IMPORTANT TIPS

Your humidifier must have the correct level of water in the base chamber to work properly. If there is too much water in the base chamber, the humidifier cannot create mist.

• Do not place the humidifier on an inclined surface.

• Never pour water directly into the base chamber. [Figure 41] Only add water to the water tank. The humidifier will automatically release the correct amount of water into the base chamber.
  

• Avoid moving or shaking the humidifier This may cause the water tank to release too much water into the base chamber.

• Before moving the humidifier, tum it off, unplug t, and remove the water tank. Empty any excess water from the base chamber.

CARE & MAINTENANCE

Note:

• Al maintenance should be done on a water-resistant surface, such as kitchen counter:
• Change the water daily to avoid bacteria growth.
• Use a tissue or cloth to clean the nozzles regularly.
• If not using the humidifier for 3 days or Inger. do not leave water inside. Clean and day the humidifier instead.

Cleaning

You should clean your humidifier water tank and base chamber every 3 days, and when you’re ready to store.

Note:

• Never immerse the base in water or fique. Do not pace any part of the humidifier in dishwasher.
• Do ot use detergents to clean the humidifier

1. Unplug the humidifier.
   Note: If you’ve been using the warm mist setting, allow the humidifier to cool before cleaning.

2. Remove and rinse the water tank cover.

3. Remove the water tank from the base, and remove the mist channel and mist tube. [Figure 5.1] Pour out any water from the tank and base chamber. If you’ve used the warm mist setting, use caution in case the water is still hot.
   Note : When pouring out water, hold down the float to ensure that it does not fall out of the base chamber.

4. Remove the water filter from the tank by rotating it counterclockwise and lifting it out. [Figure 5.2]

5. Remove the water filter sponge from the water filter if necessary for cleaning. [Figure 5.3]
   

6. Detach the mist tube from the mist channel by twisting the tube counterclockwise. [Figure 5.1]

7. Remove the float, noise silencer, absorption pad, and aroma box from the base. [Figure 5.4]

8. Detach the outer water outlet valve from the tank by rotating it counterclockwise. [Figure 5.5]

9. Rinse all parts (except the outside of the base) with room temperature water.

10. To descale the humidifier (remove mineral buildup).
    a. Remove the water filter and the water outlet valve from the tank. Remove the noise silencer and absorption pad from the base. Keep the mist tube and mist channel in place.
    b. Fill the tank with 3 US cups / 710 mL of distiled white vinegar.
    C. Replace the tank cover and swish the vinegar around the tank.
    d. Place the tank on the base and soak for 15-20 minutes. Vinegar will drain into the base chamber and loosen scale (mineral buildup) in the tank and in the base chamber (ncluding the transducer and float).
    e. Remove the tank, remove the tank cover, and pour out any vinegar.
    f. Remove the float from the base chamber by pulling up the larger side of the float and pulling the shaft out from the float brackets. One side of the float brackets is open (U-shaped) to allow the shaft to be removed. [Figure 5.6]
    9. Place the float, water filter, water outlet valve, aroma box, and noise silencer in a container. Fill with enough vinegar to cover them. Soak for 15-20 minutes.
    h. Use a soft cloth and the included cleaning brush to remove scale from all parts. [Figure 5.7]
    i. Rinse all parts until any vinegar smell is completely gone.

Cleaning the Aroma Pad & Absorption Pad 

1. Pull out the aroma box and remove the aroma pad. [Figure 5.8]
2. Remove the noise silencer, then remove the absorption pad from on top of the heating element. [Figure 5.9]
3. Rinse the pads under warm, running water.
4. Dry the pads with a clean cloth.
5. Place the aroma pad back into the aroma box.
6. Place the absorption pad back into the base.

Note: Do not use liquid cleaners or detergents to clean the pads or any other part of the humidifier.

Replacing the Aroma Pad & Absorption Pad 

If the aroma pad or absorption pad is stiff even after cleaning, then it needs to be replaced. Extra pads are included with the humidifier.

To maintain the performance of your humidifier, only use official Levoit aroma pads and absorption pads. For more information, contact Customer Support (see page 29).

Replacing the Remote Control Battery

1. Remove the battery compartment by pinching the tab in and pulling the compartment out. [Figure 5.10]
2. Remove the old battery.
3. Replace with a new 3V CR2025 battery. Make sure the polarities match
4. Replace the battery compartment
5. Dispose of the old battery according to your local laws and regulations.

Reassembling

1. Place the float back into the base chamber: [Figure 5.1]
   a. Make sure the correct side of the float is facing up.
   b. Insert the smaller prong into the closed side of the float brackets
   c. Place the larger prong into the open (U-shaped) side of the float brackets

2. Place the absorption pad and the noise silencer back over the heating element [Figure 5.12]

3. Screw the mist tube back onto the mist channel by twisting the tube clockwise. Place securely into place back over the base chamber. [Figure 5.12]

4. Place the outer water outlet valve back onto the tank by rotating it. [Figure 5.13]

5. Make sure the water filter sponge is securely placed inside the water falter. Place the water fitter back into the tank and rotate it clockwise to secure tin place. [Figure 5.14]

6. Refill the tank, if necessary. Place the tank properly on the base and place the tank cover on the water tank.

TROUBLESHOOTING

a working Outlet and turn it on.
Add purified water to the water tank.
Little a no mist canes out.| Turn the mist level to a higher setting.
Fa the water tank.
There may be too much water in the base charter. Empty the base chamber. Rail the water tank (not the base chamber) and place the water tank property onto the base.
Make sure the air Inlets on the bottom of the Dose and In the aroma box are not blocked. The humidifier should not be set on carpet or other surf aces that may block The ak Inlets.
Oean the humidifier (see Care a Maintenance. page 1)). Make sure the nozzles are not blocked or clogged.
Make sure the humidifier is on a level surface.
If the water tank or base was washed with detergent. rinse thoroughly with clean water to remove any detergent
Oean the water titer (see page 201 or replace the water litter sponge with a new one. One replacement water filter sponge is included with this humidifier. For information on additional replacements, contact Customer Supped (see page 29).
Humidifier uses water too Quickly.| The humidifier uses up water based on the environmental temperature and humidity. If your env konment is cold and/Or dry the humidifier will Nil out of water faster
Using the warm mist function wal use up water faster.
Humidifier produces an unusual smell.| ti the humidifier is new. unplug and rinse all pans. Men place in a cool, dry place for 12 hour&
n essential oas were placed on the aroma pad. rinse the pad under clean water and allow it to dry.
Oean the humidifier (see Care li Maintenance. page 17).
Humidifier makes a loud or unusual noise.| Make sure the water lank is proper?), al place (see Getting Started. page 9).
Set mist level to a lower setting.
Empty the base chanter. Refill the water tank (not the base clamber) and place the water tank properly onto the base.
When using the warm mist function, the heating element may make a gurgling noise el the water level is low. Add more water to the water tank.
The humidifier may be malftctioning. Stop using the amidiner and contact Customer Support (see page 29).
Mist leaks from the base.| Make sure the water tank is properly in place (see Getting Started. page 9).
---|---
White dust appears around or in the humidifier.| We recommend using prided to fl the humidifier. Avoid using water with nigh mineral content such as tap water.
Oean the humidifier (see Care & Maintenance, page 17).
Water teaks from the humidifier.| Avoid firming the hionidifier in a room MN over 60% relatWe humidity.
Wipe any excess water off the top and bottom 01 the base.
De not shake the humidifier.
Make sure to place the humidifier on a flat, level surface.
Check the water tank for leaks. tl there are leaks. contact Customer Support (see page 29).
the area around the humidifier is damp or wet horn condensation.| Humidity may be too high. Tian down the mist level, turn off the humidifier. or open a door or %Miaow to the room.
Open a window to ensure proper allow for the humidifier. or move the humidifier to a more wel-ventlated room.
Make sure the water tank is properly in place (see Getting Started. page 9).
When replacing the water tank. wipe off excess water from the water tank and base.
Mist is not warm after tapping 4:*.| flow the humidifier to heat up for about IS minutes to produce warm mist
Oean the heating element ‘see Care a Maintenance. page 17).
The mist is warm on the cool mist setting.| The heating element may ski be warn after being used for warm mast Mow the heating element to cool for at least 30 minutes.
Mold grows inside the humidifier.| Ciean the water tank and base chamber regularly ‘see Care a Maintenance. page 17).
el lights up red.| Fill Me water tank.
Place hie water tank properly on the base.
Clean the water finer (see page 17) or replace it with a new one. To request a new water filter. contact Customer Support (see page 29).
Essential oil has little or no smell.| Add more essential oil For best results, use pre essential oil.
Display shows an incorrect humidity percentage.| The room may be larger than the humidifiers effective range. Move to a room
---|---
smeller than 430-753 ft’ / 40-70 m2.
Moistwe may have bull up inside the humidity sensor. Make sure the Nantes are facing away from the aroma box so that mist does not settle on the sensor inside the aroma Cox (see diagram in Getting To Knew Your Smart Humidifier. page 6). Twn off the humidifier, remove the aroma box. and allow the sensor to air dry.
If the humidifier is placed within 12 inches/ 30 an of a wall or in a corner. the humidity sensor cannot provide a proper reading for relative humidity in the
room.
The humidity sensor will give an improper reading if it is exposed to dust. Avoid using the humidifier in dusty rooms. Avoid using tap water in the humidifier, as this can increase dust in the air.
The humidity level isn’t changing in my room.| Use a higher mist level setting.
Depending on your environment. the humidifier may take longer to humidity your air.
The room may be larger than the humidifiers effective range. If the room is larger than 430-753 ft’ 140-70 m’. the humidifier will not be as eftective
The humidifier does net respond to the remote.| Move remote control to within 16 K! 5 m of the humidifier.
Remove the plastic lab from the remote’s battery conpartment.
Change the battery (see Replacing the Remote Control Battery. page 20).
Display shows Error Code| The humidifier is matfundlcning. Contact Customer Support (page 291.

If your problem is not listed, please contact Customer Support (see page 29)

VESYNC APP TROUBLESHOOTING

Why isn’t my humidifier connecting to the VeSync app?

• Make sure your phone has Bluetooth® turned on and is not currently connected to another Bluetooth device.
• During the setup process, you must be on a secure 2.4GHz Wi-Fi network. Confirm that the network is working correctly.
• Make sure the Wi-Fi password you entered is correct
• Make sure your humidifier and phone are within 30 ft /10 m of each other.
• Reset the humidifier by pressing and holding for 15 seconds. Then try connecting again.

My humidifier is offline.

• Make sure the humidifier is plugged in. The humidifier may appear to be offline if it is unplugged, o ifthe outlet does not have power.
• Refresh the VeSync menu by swiping down on the screen.
• Make sure your router is connected to the intemet and your phone’s network connection is working
• Resetthe humidifier using one of these options:

a. Delete the humidifier from the VeSync app. Swipe left (0S”) or press and hold (Android), then tap Delete. Then reconfigure your humidifier with the VeSync app.
b. Pressand hold () for 15 seconds. Then reconfigure your humidifier with the VeSync app.

Note: Power outages, internet outages, or changing WI-Fi routers may cause your humidifier to go offline.

The VeSync app is displaying an incorrect humidity percentage while the humidifier is turned on.

• The room may be larger than the humidifier’s effective range. Move to a room smaller than 430-753 2/ 40-70
• Moisture may have buit up inside the humidity sensor. Make sure the nozzles are facing away from the aroma box so that mist does not settle on the sensor inside the aroma box (see diagram in Getting To Know Your Smart Humidifier, page 6). Turn off the humidifier, remove the aroma box, and allow the sensor to air dry.
• If the humidifier is placed within 12 inches / 30 cm of a wall or in a comer, the humidity sensor cannot provide a proper reading for the relative humidity in the room
• The humidity sensor will give an improper reading if it is exposed to dust. Avoid using the humidifier in dusty rooms

If your problem is not listed, please contact Customer Support (see page 29).

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT – PART 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. I this equipment does cause harmful interference to radio or television reception, which can be determined by terming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the ser’s authority to operate this equipment

FCC RADIATION EXPOSURE STATEMENT

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instructions as documented in this manual. This transmitter must not be co- located or operating in conjunction with any other antenna o transmitter. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT – PART 18

This device complies with part 18 of the FCC Rules.

This equipment generates and uses ISM frequency energy and if not installed and used properly, that is n strict accordance with the manufacturer’s instructions, may cause interference to raio and television reception. It has been type tested and found to comply with limits for an ISM Equipment pursuant to part 18 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However ,there is o guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radlio or television reception, which can be determined by tuning the equipment off and on, the users encouraged to try to correct the interference by one or more of the following

• Reorient the receiving antenna of radio o television.
• Relocate the equipment with respect to the receiver.
• Move the equipment away from the receiver.
• Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits

Conduct only the user maintenance found in this manual. Other maintenance and servicing can cause harmful interference and can void the required FCC compliance. The manufacturer is not responsible for any radio or TV interference cause by unauthorized modification to the equipment. It is the responsibilty of the user to correct such interference.

FCC SDOC SUPPLIER’S DECLARATION OF CONFORMITY

Arovast Corporation hereby declares that this equipment is in compliance with FCC requirements, The declaration of conformity may be consulted in the support section of our website, accessible from www.levoit.com

WARRANTY INFORMATION

For your own reference, we strongly recommend
that you record your order ID and date of
purchase.
Order ID|
Date of Purchase|

Levoit Limited Product Warranty

Register your products at https://warranty.levoit.com/warranty to stay up to date with important product information such as product updates, I mited warranties, usage and maintenance recommendations, and notifications concerning safety warnings or product recalls. Registration is not required to claim your limited warranty

Two (2) Year Limited Consumer Product Warranty

Arovast Corporation (“Arovast”) warrants that the product shall be free from defects in material and workmanship for a period of 2 years from the date of original purchase (“Limited Warranty Period”), provided the product was used in accordance with its use and care instructions (e.g., in the intended environment and under normal circumstances).

Your Limited Warranty Benefits

During the Limited Warranty Period and subject to this limited Warranty Policy, Arovast will, in its sole and exclusive discretion, either (i) refund the purchase price if the purchase was made directly from the online Levoit store, (ii) repair any defects in material or workmanship, (iii) replace the product with another product of equal or greater value, or (iv) provide store credit in the amount of the purchase price.

Who is Covered?

This limited warranty extends only to the original consumer purchaser of the product and is not transferable to any subsequent owner of the product. regardless of whether the product transferred ownership during the specified term of the limited warranty. The original consumer purchaser must provide verification of the defect or malfunction and proof of the date of purchase to claim the Limited Warranty Benefits

Be Aware of Unauthorized Dealers or Sellers

This limited warranty does not extend to products purchased from unauthorized dealers or sellers. Arovast’s limited warranty only extends to products purchased from authorized dealers or sellers that are subject to Arovast’s quality controls and have agreed to follow its quality controls. Please be aware, products purchased from an unauthorized website or dealer may be counterfeit, used, defective, or may not be designed for use in your country. You can protect yourself and your products by making sure you only purchase from Arovast or its authorized dealers. If you have any questions about a specific seller, or if you think you may have purchased your product from an unauthorized seller, please contact our Customer Support Team via support@levoit.com.

What’s Not Covered?

• Noma wear and tear, including parts that might wear out over time (e.g., batteries, falters cleaning brush, essential oil pads, etc) +If the proof-of-purchase has been altered in any way or is made illegible. + If the model number, serial number of production date code on the product has been altered, removed or made legible. + If the product has been modified from its original conation. +If the product has not been used in accordance with directions and instructions in the user manual – Damages caused by connecting peripherals, acditional equipment or accessories other than those recommended in the user manual, . Damages or defects caused by accident, abuse, misuse, or improper of inadequate maintenance.
• Damages or defects caused by service of repair of the product performed by an unauthorized service provider or by anyone other than Aromas.
• Damages or defects occurring during commercial use, rental use, or any use for which the product is not intended.
• If the unit has been damaged, including but not limited to damage by animals, lightning, abnormal village, fire, natural disaster, transportation, dishwasher, of water (unless the. user manual expressly states that the product is dishwasher-safe).
• Incidental and consequential damages.
• Damages or defects exceeding the cost of the. product.

Claiming Your Limited Warranty Service in 5 Simple Steps:

1. Make sure your product is within the specified limited warranty period.
2. Make sure you have a copy of the invoice and order ID of proof-of-purchase.
3. Make sure you have your product. DO NOT dispose of your product before contacting us
4. Contact our Customer Support Team via supportlevoit.com
5. Once our Customer Support Team has approved your request, please return the product with a Copy of the invoice and order ID.

Sole and Exclusive Remedy

THE FOREGOING LIMITED WARRANTY CONSTITUTES AROVAST CORPORATION’S EXCLUSIVE LIABILITY, AND YOUR SOLE AND EXCLUSIVE REMEDY, FOR ANY BREACH OF ANY WARRANTY OR OTHER NONCONFORMITY OF THE PRODUCT COVERED BY THIS LIMITED PRODUCT WARRANTY STATEMENT. THIS LIMITED WARRANTY IS EXCLUSIVE, AND IN LIEU OF ALL OTHER WARRANTIES. NO EMPLOYEE OF AROVAST CORPORATION OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY IN ADDITION TO THE LIMITED WARRANTY IN THIS LIMITED PRODUCT WARRANTY STATEMENT

Disclaimer of Limited Warranties

TO THE FULLEST EXTENT PROVIDED BY APPLICABLE LAW, EXCEPT AS WARRANTED IN THIS LIMITED PRODUCT WARRANTY POLICY, AROVAST CORPORATION PROVIDES THE PRODUCTS YOU PURCHASE FROM AROVAST CORPORATION “AS IS” AND AROVAST CORPORATION HEREBY DISCLAIMS ALL WARRANTIES OF ANY KIND, WHETHER EXPRESS OR IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, AND FITNESS FOR PARTICULAR PURPOSE.

Limitations of Liability

TO THE FULLEST EXTENT PROVIDED BY APPLICABLE LAW, IN NO EVENT WILL AROVAST CORPORATION, ITS AFFILIATES, OR THEIR LICENSORS, SERVICE PROVIDERS, EMPLOYEES, AGENTS, OFFICERS, OR DIRECTORS BE LIABLE FOR:

(a) DAMAGES OF ANY KIND ARISING OUT OF OR IN CONNECTION WITH PRODUCTS PURCHASED FROM AROVAST CORPORATION IN EXCESS OF THE PURCHASE PRICE PAID BY THE PURCHASER FOR SUCH PRODUCTS, OR

(b) INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES EVEN IF AROVAST CORPORATION OR ONE OF ITS SUPPLIERS HAS BEEN ADVISED OF THE POSSIBILITY OR LIKELIHOOD OF SUCH DAMAGES

AND REGARDLESS OF WHETHER CAUSED BY TORT (INCLUDING NEGLIGENCE), BREACH OF CONTRACT, OR OTHERWISE, OUR LIABILITY SHALL UNDER NO CIRCUMSTANCES EXCEED THE ACTUAL AMOUNT PAID BY YOU FOR THE DEFECTIVE PRODUCT, NOR SHALL WE UNDER ANY CIRCUMSTANCES BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, SPECIAL OR PUNITIVE DAMAGES OR LOSSES, WHETHER DIRECT OR INDIRECT

EXCEPT AS COVERED BY THIS LIMITED PRODUCT WARRANTY STATEMENT, AROVAST CORPORATION SHALL NOT BE LIABLE FOR COSTS ASSOCIATED WITH THE REPLACEMENT OR REPAIR OF PRODUCTS PURCHASED FROM IT, INCLUDING, BUT NOT LIMITED TO, LABOR, INSTALLATION, OR OTHER COSTS INCURRED BY THE USER AND, IN PARTICULAR, ANY COSTS RELATING TO THE REMOVAL OR REPLACEMENT OF ANY PRODUCT.

OTHER RIGHTS YOU MAY HAVE

SOME JURISDICTIONS DO NOT ALLOW FOR: (1) EXCLUSION OF IMPLIED WARRANTIES; (2) LIMITATION ON THE DURATION OF IMPLIED WARRANTIES; AND/ OR (3) EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE DISCLAIMERS IN THIS POLICY MAY NOT APPLY TO YOU. IN THESE JURISDICTIONS YOU HAVE ONLY THE IMPLIED WARRANTIES THAT ARE EXPRESSLY REQUIRED TO BE PROVIDED IN ACCORDANCE WITH APPLICABLE LAW. THE LIMITATIONS OF WARRANTIES, LIABILITY, AND REMEDIES APPLY TO THE MAXIMUM EXTENT PERMITTED BY LAW.

ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS IN YOUR JURISDICTION. THIS STATEMENT OF LIMITED WARRANTY IS SUBJECT TO APPLICABLE LAWS THAT APPLY TO YOU AND THE PRODUCT. PLEASE REVIEW THE LAWS IN YOUR JURISDICTION TO UNDERSTAND YOUR RIGHTS FULLY.

CHANGES TO THIS POLICY

We may change the terms and availability of this limited warranty at our discretion, but any changes will not be retroactive.

This warranty is made by:

Arovast Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806

CUSTOMER SUPPORT

If you have any questions or concerns about your new product, please contact our helpful Customer Support Team

Arovast Comoration
1202 N. Miller St., Suite A
Anaheim, CA 92806, USA

Email: support@levoit.com
Toll-Free: 388-726-8520

Support Hours

Mon—Fri, 9:00 am-5:00 pm PST/PDT
English only

*Please have your order invoice and order ID ready before contacting Customer Support

ATTRIBUTIONS

Apple App Store s a trademark of Apple Inc.

Google, Android, and Google Play are trademarks of Google LLC.

Wi-Fi® is a registered trademark of Wi-Fi Alliance®.

Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. of its affiliates.

105 is a registered trademark of Cisco Systems, Inc. and/or s affiiates in the United States and certain other countres.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Arovast Corporation is under license. Other trademarks and trade names are those of their respective owners

References

• . Spend less. Smile more.
• Vesync-Warranty Registration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>