chicco Next2Me Magic Bedside Crib User Manual

June 11, 2024
chicco

chicco Next2Me Magic Bedside Crib - Logo Next2Me Magic Bedside Crib
User Manual

chicco Next2Me Magic Bedside Crib -

Next2Me Magic Bedside Crib

chicco Next2Me Magic Bedside Crib - Featured| chicco Next2Me Magic Bedside Crib - Fig
---|---
chicco Next2Me Magic Bedside Crib - Fig 1| chicco
Next2Me Magic Bedside Crib - Fig 2
chicco Next2Me Magic Bedside Crib - Fig 3

IMPORTANT CAREFULLY AND KEEP FOR FUTURE REFERENCE.

WARNING: TO AVOID THE DANGER OF SUFFOCATION REMOVE THIS PLASTIC COVER BEFORE USING THE PRODUCT. THIS COVER SHOULD BE DESTROYED OR KEPT AWAY FROM BABIES AND CHILDREN.
WARNINGS

  • Only for domestic use.
  • WARNING: Do not use this product without reading the instructions for use first.
  • WARNING: When in its highest position the product is intended for use by children of 0 to 5/6 months (weighing up to 9 kg).
  • WARNING: Stop using the product as soon as the child can sit or kneel or pull itself up.
  • WARNING: Placing additional items in the product may cause suffocation.
  • WARNING: Do not use the product if any part is broken, torn or missing.
  • WARNING: DO NOT USE the product in“Crib Configuration” and/or “Bedside sleeper Configuration” if any part is missing, damaged or broken. Contact Artisanal Sp A for spare parts and user instructions if needed DO NOT REPLACE missing, damaged or broken parts with non-OEM components or components not approved by Artisanal
  • WARNING: Consult the user manual for the list of components. Examine the product regularly to make sure that there are no loose, damaged or missing parts.
  • WARNING: Always use all parts needed for each configuration of use.
  • WARNING: Be aware of the risk of burns from cigarettes, naked flames and other heat sources, like electric or gas heaters, that are near the crib.
  • Before assembly, check that the product and all of its components have not been damaged during transportation. Should any part be damaged, keep out of reach of children and do not use.
  • Make sure that the adult using the product knows exactly how it works.
  • WARNING: The product is ready for use only when all locking mechanisms are engaged. Make sure they are securely engaged before use.
  • WARNING: When your child is unattended and the product is in “Crib Configuration”, always make sure that the side is raised and locked in the closed position and aligned with the upper perimeter of the crib.
  • When the product is being used, and above all in “Crib Configuration”, the wheels must always be locked.
  • All operations for opening, adjusting, fastening and installing the product must be carried out by an adult.
  • Before using in the “Bedside sleeper Configuration” (fastened to bed), make sure the product is fastened and installed correctly. Check the fastening system hold before each use by attempting to push the crib away from the parents’ bed.
  • The fixing straps are included in the packaging. Other fastening systems should not be used.
  • To prevent danger of choking due to the child’s head being trapped, when the crib is in the “Bedside sleeper Configuration” (fastened to the bed) it should be properly fastened to the parents’ bed with the fixing straps as explained in the in struct ion booklet.
  • WARNING: Before placing the child inside the crib when the product is in the “Bedside sleeper Configuration” (fastened to the bed), be sure that the fixing straps are fastened and tightened correctly. The product must be attached to the parents’ bed frame/support and there should be no gaps between the lowest part of the Bedside sleeper crib and the parents’ mattress.
  • If there are gaps between the lowest part of the Bedside sleeper crib and the parents’ mattress, DO NOT use the product.
  • Do not fill any spaces or gaps between the parents’ mattress and the crib with pillows, blankets, bedsheets or any other material that may cause a choking hazard.
  • DANGER! The Bedside sleeper, when not attached to the adult’s bed, shall have all its sides in place and/or in their highest position.
  • WARNING: To avoid hazards from the child’s neck being caught on the top rail on the side that is next to the adult bed, the top rail must not be higher than the adult bed mattress.
  • WARNING: To avoid the risk of your child being strangled the attachment system to the adult’s bed shall always be kept away from and out of the crib.
  • The product must always be placed on a horizontal surface. Never leave the product on a sloping surface with your child inside.
  • Unattended children must not be left to play near the product.
  • Do not use the product without the frame.
  • Keep the fixing straps out of reach of children.
  • Only use the mattress provided with the product or replacement mattresses approved by Artisan.
  • WARNING: Do not use more than one mattress in the product. Only use the mattress that comes with the product.
  • WARNING: Only use the mattress sold with this crib, do not add a second mattress on this one, suffocation hazard.
  • WARNING: When not attached to the bed, the crib can be inclined by a maximum of 4 positions between one leg sup- port and the other.
  • Infants can suffocate on soft bedding.
  • Avoid placing pillows or similar items under newborn babies for additional comfort during sleep.
  • Use the crib in the “Bedside sleeper Configuration” (fastened to the bed) only with beds of the size indicated in the reference figure at the beginning of the manual.
  • Do not leave anything inside the product that might reduce its depth.
  • To prevent the child from being trapped, do not place the crib close to walls or obstacles.
  • Do not leave any small objects inside the product that might be swallowed.
  • Only use spare parts approved by the manufacturer. Do not attach any accessories to the product that have not been supplied by the manufacturer.
  • Do not make adjustments to the product when the child is in it.
  • When in the “Bedside sleeper Configuration” (fastened to the bed), the crib must never be inclined.
  • Do not move the product when the child is inside.
  • Do not use the product with more than one child at a time.
  • WARNING: Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc To avoid strangulation hazards, never give children objects with strings attached, or leave these objects within their reach.
  • Prolonged exposure to direct sunlight may cause the product’s colour to fade. After prolonged exposure of the product to high temperatures, wait a few minutes prior to putting your child in it.
  • All assembly couplings must be fastened correctly. Be sure there are no loose screws, as a child’s body or clothing (e.g., laces, necklaces, cords from pacifiers) may get trapped and cause a strangulation hazard.
  • Keep the product out of reach of children when it is not in use.
  • WARNING: Be careful when the child is in the crib, that objects or bedding items do not fall into the crib.

COMPONENTS
A. Leg rest with wheels
A1. Height adjustment button
A2. Height indicator
A3. Telescopic foot release button
A4. Telescopic feet
A5. Wheels with brakes
A6. Central support structure slot
A7. Bottom bar slots
A8. Upper structure fastening support
A9. Upper structure release button

B. Bottom bar
C. Central support structure
D. Crib structure
D1. Fabric
D1.1 Front vertical zippers
D1.2 Upper zipper
D1.3 Fabric attachment buttons
D1.4 Side support upright openings
D2. Upper frame
D3. Structure/leg support fasteners
D4. Crib structure side upright fasteners
D5. Side tilting button
D6. Crib bottom
D7. Front strap fastening buckle
D8. Rear strap fastening buckle
D9. Mattress stopper

E. Crib structure side uprights
E1. Locking/unlocking right tilting function
E2. Locking/unlocking left tilting function
E3. Safety levers
F. Fastening straps
F1. Red crib front fastening buckle
F2. Grey crib rear fastening buckle
F3. Grey bed fastening and height adjustment buckle
G. Mattress with removable lining
H. Bag

ASSEMBLY OF THE CRIB

  1. Hold the bottom support “A” and insert the lower bar “B” in the relevant slot “A7” (Fig.1), pushing the metal pin until you hear the click. Repeat the same operation for both feet (Fig.1A).
  2. Now insert the central support structure “C” into the slots “A6” on both leg support, pushing the metal pin until you hear the click (Fig.2-3).
  3. Hold the frame “D2” and turn the upper part of the frame by 90° (Fig.4). Repeat the same operation for the bottom of the crib “D6” (Fig.5).
  4. Pass the side support uprights “E” through the openings “D1.4”, on both sides of the crib (Fig.6), until they are inserted into the fasteners “D4”, making sure that you have heard the click of correct installation (Fig.7).
  5. Close the vertical front zippers “D1.1” (Fig.8) and then the upper hinge “D1.2” (Fig.9).
  6. Fasten the buttons “D1.3” located in the upper front corners, and in the front and rear areas of the bottom of the crib (Fig.10-11-12).
  7. Fasten the crib structure “D” to the legs “A” inserting the couplers “D3” in the “A8” supports located on both legs (Fig.13), until you hear the click. Be careful to position the structure “D” so that the tilting front panel faces in the same direction as the telescopic feet “A4”.
  8. Insert the mattress “G” inside the crib structure “D”, paying attention to orient the breathable net surface upwards. Make sure the mattress rests against the stopper “D9” (Fig.14).
  9. Block the 4 wheels “A5” of the crib by lowering the levers that activate the brakes (Fig.15). The crib is now ready to be used.

ADJUSTING THE CRIB HEIGHT
The crib can be adjusted in 11 different heights. To adjust the height, press the buttons “A1” on the leg support “A” and lift or lower the structure “D” to the desired position (Fig.16). Release after hearing the click. The base of the crib can be slightly inclined by adjusting the leg supports to different heights (Fig.17).
WARNING: The crib can be inclined by a maximum of 4 positions between one leg support and the other (e.g., right leg support in position 5 and left leg support in position 1 (Fig. 18).
WARNING: The child’s head must always be positioned near the raised end (Fig.19).
WARNING: It is not possible to select different heights on the two sides of the crib when in rocking configuration. You can deactivate the tilting function by rotating and
fastening the locks E1-E2 on the central support structure bar and ensuring that you hear the locking click of the safety levers E3 located on the locks (Fig.21A-21B-21C).
WARNING: If the crib has been used previously in “Side sleeping configuration (fastened to the bed),” make sure that the side is in locked position and check that it is engaged correctly.
WARNING: Always remember to deactivate rocking configuration when using the product in “Side sleeping (fastened to the bed)” or when the child is unattended.
WARNING: It is not possible to select different heights on the two sides of the crib when in rocking function.

SIDE SLEEPING CONFIGURATION (FASTENED TO THE BED)
It is possible to fasten the crib to the parents’ bed (side sleeping configuration).
WARNING – IMPORTANT FOR YOUR CHILD’S SAFETY: This configuration is allowed only with beds that allow compliancy with all the conditions described in this paragraph. In particular, the LOWERED side of the crib must always be positioned against the mattress of the parents’ bed and the parents’ mattress must be aligned with the height of the crib’s side (Fig.22A-22B). Moreover, the crib must be fastened to the structure of the parents’ bed or to the mattress support (mesh or slat sprung base).
WARNING: Check that the structure of the crib in side sleeping configuration does not interfere with the parents’ bed.
WARNING: During use, make sure that the bedsheets, blankets, etc. do not interfere with the crib’s space.

  1. Lower the side of the crib by pushing button “D5” and accompanying the side until it reaches the end of its travel (Fig.23).
    WARNING: Use the crib with the side lowered only in side sleeping mode, (fastened to the bed).

  2. Put the crib against the parents’ bed and check its height compared to the parents’ mattress (Fig.24).
    WARNING: The height of the parents’ mattress must be higher than or the same as that of the side of the crib, (fastened to the bed). If this is not the case, use the adjustment system to achieve this condition on both sides.
    WARNING: In side sleeping configuration, the 2 leg supports of the crib must be set at the same height.

  3. To fasten the crib to the parents’ bed (side sleeping configuration), use the pair of supplied straps “F”.

  4. Carefully release the buckles “D6” and “D7” by pushing them slightly upwards and then pulling them out (Fig.25).

  5. Fasten the grey buckles “F2” to the buckles “D6” located in the rear part of the bottom of the crib “D4” (Fig.26).

  6. Fasten the red buckles “F1” to the buckles “D7” located in the front part of the bottom of the crib “D4” (Fig.27).

  7. Then pass the straps around the parents’ bed structure from top to bottom (Fig.28) and fasten the grey buckles “F3” to form a loop (Fig.29). Make sure to repeat the step on both sides. To make installation easy, when fastening the buckles, always keep the crib slightly away from the parents’ bed.

  8. At this point put the crib against the parents’ bed and tighten the noose pulling the straps (Fig.30). Carry out this step first on one side and then on the other, adjusting the straps until the crib is in contact with the parents’ mattress.
    WARNING: Before use, always make sure that there is no space between the parents’ mattress and crib’s side. Otherwise adjust the straps pulling them until the required condition is restored. Make sure that the side is always free to be lowered and raised completely.

  9. Lock the crib’s wheels. If when fastening the crib to the parents’ bed it is not possible to fit the crib’s feet under the parents’ bed, the crib can be fastened anyway by the following the instructions above and retracting the telescopic feet “A4” when putting the crib against the bed. To activate retraction, simply push the crib towards the bed so that the release buttons “A3” (Fig.31) are activated, retracting the feet as much as necessary to install the crib correctly.

  10. To close the side, simply lift it upwards, holding it from the centre (Fig.32). Always make sure that it is engaged correctly.

WARNING: Whenever the side is lowered, make sure that the position compared to the parents’ mattress has not changed from that illustrated in the paragraphs above. WARNING: Never use the rocking function when the crib is in “Side sleeping configuration (fastened to the bed).”
WARNING: Use the product with beds and/or mattresses with straight sides only. Do not use the product with round beds and/or mattresses or water mattresses.
WARNING: When the product is used in “Side sleeping configuration (fastened to the bed),” it must always be mounted on the long side of the bed. DO NOT install the product at the head or feet of the bed.

CARE AND MAINTENANCE
The crib and mattress have a resistant fabric lining that can be removed completely and washed.
To remove the fabric, follow the instructions in the paragraph “HOW TO REMOVE THE FABRIC COVER.”
WARNING: Covering or removing the fabric may take a few minutes and must be carried out by an adult.
Regularly inspect the crib for signs of wear and any damage.
In the case of damage do not use and keep out of reach of
children.
When washing the fabrics pay close attention to the instructions on the label.
Do not use solvents, abrasive or overly aggressive products
Hand wash in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean

Check that the fabric and the stitching are in good condition after each wash.
WARNING: When covering or removing the cover, take care when handling the fabric parts so as to avoid accidental tearsor damage.
WARNING: The fabric part of drop side cannot be removed. Do not open the zipper.

MAKING THE BED
It is possible to unfasten the crib from the parents’ bed when making the b ” have been completed.

MAKING THE BED
It is possible to unfasten the crib from the parents’ bed when making the bed. Just unfasten the grey buckles under the fabric lining.
When fastening the crib again to the parents’ bed, pull the straps again to make sure that the crib is correctly and securely fastened to the parents’ bed. Make sure that all the steps illustrated above in “Side sleeping configuration (fastened to the bed)” have been completed.
REMOVING THE COVER

  1.  Remove the mattress.
  2. Release the crib structure “D” from the feet “A” by pushing the buttons “A9” and pulling it upwards (Fig.33).
  3. Open the 3 zippers “D1.1” and “D1.2” on the fabric.
  4. Release the fastening buttons “D1.3.”
  5. Remove the side support uprights “E” by pushing on the  appropriate tabs (Fig.34) and operating on the pins in the upper fasteners to remove them from the fabric.
  6. You can now remove the lining.

DISASSEMBLING THE CRIB
The crib can be disassembled completely to put it away in the supplied bag. In order to complete the disassembly of the crib after removing the fabric, remove the bottom bar “B” and the central support structure “C” by repeating the steps illustrated in “ASSEMBLY OF THE CRIB.”

WARRANTY
The product is guaranteed against any conformity defect in normal conditions of use as provided for by the instructions. The warranty shall not therefore apply in the case of damage caused by improper use, wear or accidental events. For the duration of the warranty on conformity defects please refer to the specific provisions of applicable national laws in the country of purchase, where appropriate.
ARTSANA UK Ltd.
2nd Floor
1 Imperial Place
Maxwell Road
Dreamworld
Hertfordshire – WD6 1JN
0208 953 6627 (office hours)
www.CHICCO.uk.com

ARTSANA S.p.A.
Tel. (+39) 031 382 111 – Fax (+39) 031 382 400
www.chicco.com

Reference:chicco Next2Me Magic Bedside Crib User Manual- device.reprot

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals