ELIMINATOR LIGHTING Furious Five RG 5-in-1 Lighting Effect Fixture | Sweetwater User Manual
- June 4, 2024
- Eliminator LIGHTING
Table of Contents
- Furious Five RG 5-in-1 Lighting Effect Fixture | Sweetwater
- GENERAL INFORMATION
- LIMITED WARRANTY (USA ONLY)
- SAFETY GUIDELINES
- MAINTENANCE GUIDELINES
- INSTALLATION INSTRUCTIONS
- SYSTEM MENU
- IR REMOTE OPERATION
- DIMENSIONAL DRAWINGS
- SPECIFICATIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Furious Five RG
User Manual
SKU#: Furious Five RG
UPC#: 818651028096
ITF-14#: 10818651028093
Furious Five RG 5-in-1 Lighting Effect Fixture | Sweetwater
©2020 Eliminator Lighting all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without
notice. Eliminator logo and identifying product names and numbers herein are
trademarks of Eliminator Lighting. Copyright protection claimed includes all
forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this
document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-Eliminator brands and product
names are trademarks or registered trademarks of their respective companies.
Eliminator Lighting and all affiliated companies hereby disclaim any and
all liabilities for property, equipment, building, and electrical damages,
injuries to any persons, and direct or indirect economic loss associated with
the use or reliance of any information contained within this document, and/ or
as a result of the improper, unsafe, insufficient and negligent assembly,
installation, rigging, and operation of this product.
Eliminator Lighting USA
6122 S. Eastern Ave. | Los Angeles, CA 90040 USA Tel:
323-948-0480 | Fax:
888-287-5224 |
www.eliminatorlighting.com |
info@eliminatorlighting.com
DOCUMENT VERSION An updated version of this document may be available online. Please check www.eliminatorlighting.com for the latest revision/update of this document before beginning installation and use.
Date| Document Version| Software Version| DMX Channels|
Notes
---|---|---|---|---
09/01/2020| 1.0| 1.0| 11 / 24 Channels| Initial Release
GENERAL INFORMATION
INTRODUCTION
Please read and understand all instructions in this manual carefully and
thoroughly before attempting to operate this product. These instructions
contain important safety and use information.
UNPACKING: This product has been thoroughly tested and has been shipped
in perfect condition. Carefully check the shipping carton for damage that may
have occurred during shipping. If the carton appears to be damaged, carefully
inspect your product for damage and be sure all accessories necessary to
assemble the product have arrived intact. In the event that damage has been
found or parts are missing, please contact our customer support team for
further instructions. Please do not return this product to your dealer without
first contacting customer support at the number listed below. Please do not
discard the shipping carton in the trash. Please recycle whenever possible.
CUSTOMER SUPPORT
Tel: 323-213-4592 | Fax:
323-582-2941
www.eliminatorlighting.com |
support@eliminatorlighting.com
WARRANTY RETURNS
All returned service items, whether under warranty or not, must be freight
pre-paid and accompanied by a return authorization (R.A.) number. The R.A.
number must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be written
down on a piece of paper and included in the shipping container. If the unit
is under warranty, you must provide a copy of your proof of purchase invoice.
Items returned without an R.A. number clearly marked on the outside of the
package will be refused and returned at the customer’s expense. You may obtain
an R.A. number by contacting customer support.
LIMITED WARRANTY (USA ONLY)
A. Eliminator Lighting, an ADJ Products, LLC brand, hereby warrants, to the
original purchaser, ADJ Products, LLC products to be free of manufacturing
defects in material and workmanship for a prescribed period from the date of
purchase (see specific warranty period listed below). This warranty shall be
valid only if the product is purchased within the United States of America,
including possessions and territories. It is the owner’s responsibility to
establish the date and place of purchase by acceptable evidence, at the time
service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product, please contact ADJ Products, LLC Service
Department at 800-322-6337. Send the
product only to the ADJ Products, LLC factory. All shipping charges must be
pre-paid. If the requested repairs or services (including parts replacement)
are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the
entire instrument is sent, it must be shipped in its original package. No
accessories should be shipped with the product. If any accessories are shipped
with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, or for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if
the product is modified in any manner which ADJ Products, LLC concludes, after
inspection, affects the reliability of the product; if the product has been
repaired or serviced by anyone other than the ADJ Products, LLC factory unless
prior written authorization was issued to purchaser by ADJ Products, LLC; if
the product is damaged because not properly maintained as set forth in the
instruction manual.
D. This is not a service contract, and this warranty does not include
maintenance, cleaning, or periodic check-up. During the period specified
above, ADJ Products, LLC will replace defective parts at its expense with new
or refurbished parts and will absorb all expenses for warranty service and
repair labor by reason of defects in material or workmanship. The sole
responsibility of ADJ Products, LLC under this warranty shall be limited to
the repair of the product, or replacement thereof, including parts, at the
sole discretion of ADJ Products, LLC. All products covered by this warranty
were manufactured after August 15, 2012, and bear identifying marks to that
effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or
improvements to its products without any obligation to include these changes
in any products theretofore manufactured. No warranty, whether expressed or
implied, is given or made with respect to any accessory supplied with the
products described above. Except to the extent prohibited by applicable law,
all implied warranties made by ADJ Products, LLC in connection with this
product, including warranties of merchantability or fitness, are limited in
duration to the warranty period set forth above. And no warranties, whether
expressed or implied, including warranties of merchantability or fitness,
shall apply to this product after said period has expired. The consumer’s
and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC
be liable for any loss or damage, direct or consequential, arising out of the
use of, or inability to use, this product.
This warranty is the only written warranty applicable to Eliminator Lighting,
an ADJ Products, LLC brand, and supersedes all prior warranties and written
descriptions of warranty terms and conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
All Eliminator Lighting products (except laser diodes) = 1-year (365
days) Limited Warranty (Such as Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls,
Par Cans, Trussing, Lighting Stands, etc., excluding lamps)
Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser
diodes which have a 6-month limited warranty)
Batteries = 180-Day Limited Warranty
To register your Eliminator Lighting product online, please click here on the
ADJ Warranty Registration Page: https://www.adj.com/portal/user/register/
SAFETY GUIDELINES
To ensure smooth operation, it is important to follow all instructions and
guidelines in this manual.
ELIMINATOR LIGHTING is not responsible for injury and/or damages
resulting from the misuse of these devices due to the disregard of the
information printed in this manual. Only qualified and/or certified personnel
should perform the installation of these devices and only the original rigging
parts included with these devices should be used for installation. Any
modifications to these devices and/or the included mounting hardware will void
the original manufacturer’s warranty and increase the risk of damage and/or
personal injury.
THERE ARE NO USER-SERVICEABLE PARTS INSIDE THESE DEVICES. DO NOT ATTEMPT ANY
REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES
RESULTING FROM MODIFICATIONS TO THESE DEVICES AND/OR THE DISREGARD OF SAFETY
INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY
AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
NEVER TOUCH LIGHT DURING OPERATION, AS IT MAY BE HOT! ALWAYS DISCONNECT FROM
THE MAIN POWER BEFORE REPLACING LAMPS! ALWAYS REPLACE LAMPS AND FUSES WITH
REPLACEMENTS OF THE SAME TYPE! KEEP FLAMMABLE MATERIALS AWAY FROM THESE
DEVICES!
INDOOR / DRY LOCATIONS USE ONLY! DO NOT EXPOSE DEVICES TO RAIN AND/OR
MOISTURE!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK – MAY INDUCE
BLINDNESS! SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
RISK GROUP 3 – RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION! THE FIXTURE EMITS A HIGH-INTENSITY WAVELENGTH OF ULTRAVIOLET LIGHT AT A WAVELENGTH OF 395NM 400NM. WEAR PROPER EYE AND SKIN PROTECTION. DO NOT OPERATE A FIXTURE WITH A DAMAGED/MISSING EXTERNAL COVER PROTECTIVE LENS. DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT. AVOID PROLONGED PERIODS OF EXPOSURE. AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON THE SKIN. AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m). INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY EXPERIENCE DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.
DO NOT position the device close to any FLAMMABLE MATERIALS while
operating.
DO NOT attempt installation and/or operation of the device without
knowledge of how to do so.
DO NOT permit operation by persons who are not qualified to operate these
types of devices.
DO NOT shake the device, and avoid brute force when installing and/or
operating.
DO NOT operate this device if the main power cord has become frayed,
crimped, and/or damaged. Replace any damaged power cords with cords of a
similar power rating.
DO NOT remove or break off the ground plug from the device power cords.
DO NOT remove or disassemble devices, there are NO user-serviceable parts
inside.
ALWAYS disconnect the device from the main power source before performing
any cleaning.
ALWAYS disconnect the light from the main power before replacing the lamp
ALWAYS be sure to install this device in an area that will allow proper
ventilation.
NEVER remove the ground prong from the power cable.
Power cords should be safely routed and secured so they are not likely to get
pinched.
Disconnect power cords during long periods of non-use.
Only use recommended rigging hardware as described in this guide.
Use the original packaging and materials to transport this device for service.
This device should be serviced by qualified service personnel when:
- The power cords or plugs have become damaged.
- Objects have fallen on and/or liquid has spilled into the device.
- The device has been exposed to rain and/or moisture.
- The device does not operate normally or exhibits a marked change in performance.
MAINTENANCE GUIDELINES
DISCONNECT POWER BEFORE PERFORMING ANY CLEANING OR MAINTENANCE!
CLEANING
Frequent cleaning is recommended to ensure proper function, optimized light
output, and extended life. The frequency of cleaning depends on the
environment in which the device operates: damp, smoky, or particularly dirty
environments can cause a greater accumulation of dirt on the fixture housing
and/or light fixture optics. Clean the external surface and the front lens of
the device periodically with a soft cloth to avoid dirt/debris accumulation
NEVER use alcohol, solvents, or ammonia-based cleaners.
MAINTENANCE
Regular inspections are recommended to ensure proper function and extended
life. There are no user-serviceable parts inside these devices, please refer
all other service issues to Eliminator Lighting. Should you need any spare
parts, please order genuine parts from Eliminator Lighting. Please refer to
the following points during routine inspections:
- A detailed review should be performed by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating.
- Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during normal operation, resulting in damage or injury as larger parts could fall.
- Check for any deformations on the unit. Deformations could allow for dust to enter the device or cause the device to fall and seriously injure a person(s).
- Electric power supply cables must not show any damage, material fatigue, or sediments.
FUSE REPLACEMENT
This device features a replaceable fuse located alongside the Power Input on
the back side of the device. To access the fuse, use a flathead screwdriver to
catch the groove in the wall of the Power Input. BE CAREFUL NOT TO DAMAGE
THE FUSE CLIP, THE POWER INPUT, OR THE PRONGS. The clip contains one
operational fuse and one spare. The operational fuse is the exposed fuse which
sits further back in the fuse socket, while the spare fuse is enclosed within
the square section clip housing. Please refer to the images below.
REPLACE THE FUSE ONLY WITH AN IDENTICAL F5A 250V FUSE.
OVERVIEW
1. Adjustable Mounting Bracket
2. Bracket Adjustment Knobs (x2)
3. 4-color LED Spotlights (x2)
4. UV Lights (x4)
5. 4-in-1 LEDs (x6)
6. 5730 White LED
7. Red/Green Laser
8. Display Screen
9. Safety Cable Attachment Point| 10. Power In
11. Fuse
12. Menu Button
13. Down Button
14. Up Button
15. Enter Button
16. DMX In
17. DMX Out
---|---
INCLUDED ITEMS:
- Power Cable (x1)
- Wireless IR Remote (x1)
INSTALLATION INSTRUCTIONS
FLAMMABLE MATERIAL WARNING
Keep devices at least 5.0 feet (1.5m) away from flammable materials and/or
pyrotechnics.
ELECTRICAL CONNECTIONS
A qualified electrician should be used for all electrical connections and/or
installations.
DO NOT INSTALL THE DEVICE IF YOU ARE NOT QUALIFIED TO DO SO!
OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, INCLUDING CALCULATING
WORKING LOAD LIMITS, KNOWLEDGE OF INSTALLATION MATERIAL BEING USED, AND
PERIODIC SAFETY INSPECTION OF ALL INSTALLATION MATERIALS. IF YOU LACK THESE
QUALIFICATIONS, DO NOT ATTEMPT THE INSTALLATION YOURSELF. IMPROPER
INSTALLATION CAN RESULT IN BODILY INJURY.
BEFORE RIGGING/MOUNTING DEVICES TO ANY METAL TRUSS/STRUCTURE OR CEILING, A
PROFESSIONAL EQUIPMENT INSTALLER MUST BE CONSULTED TO DETERMINE WHETHER THE
METAL TRUSS/STRUCTURE OR CEILING IS PROPERLY CERTIFIED TO SAFELY HOLD THE
COMBINED WEIGHT OF THE LIGHT FIXTURE, CLAMPS, CABLES, AND ACCESSORIES. BEFORE
MOUNTING DEVICES TO ANY SURFACE OR STRUCTURE, MAKE SURE THE SURFACE OR
STRUCTURE CAN HOLD A MINIMUM POINT LOAD OF 10 TIMES THE WEIGHT OF THE
DEVICES.
MAKE SURE SCREWS AND/OR ANCHOR BOLTS (NOT INCLUDED) FIT INTO MOUNTING
HOLES!
FOR ADDED PROTECTION, MOUNT DEVICES OUTSIDE WALKING PATHS, SEATING AREAS,
OR AREAS WHERE UNAUTHORIZED PERSONNEL CAN REACH THE DEVICES. SECURE FIXTURE
WITH A SECONDARY SAFETY ATTACHMENT, SUCH AS AN APPROPRIATE SAFETY CABLE. (NOT
INCLUDED)
NEVER STAND DIRECTLY BELOW THE DEVICES WHEN MOUNTING, REMOVING, OR
SERVICING.
DEVICES MUST ALL BE INSTALLED FOLLOWING ALL LOCAL, NATIONAL, AND COUNTRY
COMMERCIAL ELECTRICAL AND CONSTRUCTION CODES AND REGULATIONS.
CLAMP INSTALLATION
This fixture features a mounting clamp attachment point, which is located on
the mounting yoke, as well as a safety cable rigging point, located on the
rear face of the unit above the central cooling fan (see the illustration
below). When mounting the fixture to a truss or any other suspended or
overhead installation, be sure to secure an appropriately rated clamp ( not
included ) to the clamp attachment point and attach a separate SAFETY CABLE
of the appropriate safety rating to the safety cable rigging point.
SAFETY CABLE
ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE IN A
SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE WILL NOT FALL IF THE CLAMP
FAILS.
RIGGING
Overhead rigging requires extensive experience, including but not limited to:
calculating working load limits, understanding the installation material being
used, and periodic safety inspection of all installation material and the
fixture itself. If you lack these qualifications, do not attempt to perform
the installation yourself. Improper installation can result in bodily injury.
SYSTEM MENU
CONTROL PANEL
The device includes an easy-to-navigate system menu that can be accessed via a
set of control buttons located on the back face of the device below the
digital display.
Menu: Cycles through main menu options.
Down (▽ ) / Up (△ ): Scrolls through options in the current menu.
Enter: Selects the option currently shown on the digital display.
SYSTEM MENU
A _ | A000 – A512 | DMX address |
---|
CHAD
| CH11| 11-channel DMX mode
CH24| 24-channel DMX mode
FAIL
| OFF| The fixture turns off when the DMX signal is lost
NAST/SLAV| Allows fixture to be set to Master or Slave mode
HOLD| Fixture continues to operate according to settings in use prior to loss
of DMX signal
BUT _
| AUT0| Show speed, slow to fast: (SP01 – SP16)| Full system auto show
AUT1| Red/green laser auto show
AUT2| 5730 white LED auto show
AUT3| 4-in-1 LED + UV auto show
AUT4| 4-color LED spot auto show
SOU _
| SOU0| Sound sensitivity, low to high: (SE00 – SE99)| Full system sound show
SOU1| Red/green laser sound show
SOU2| 5730 white LED sound show
SOU3| 4-in-1 LED + UV sound show
SOU4| 4-color LED spot sound show
ERIC| ON / OFF| Remote control capability
LED| ON / OFF| Display screen always-on mode. Selecting OFF turns the
display screen off after 60 seconds of inactivity.
VER| 2.0| Software version
DMX TRAITS
Eliminator Furious Five RG – DMX Traits
Software Version 2.0
CHANNEL| DMX VALUE| DESCRIPTION
11-CH MODE| 24-CH MODE
| 1| 000 – 255| Master Dimmer , 0 to 100%
| 2| | UV Strobe
000 – 007| No strobe
008 – 255| Strobe, slow to fast
| 3| | UV Dimmer
000 – 007| Off
008 – 255| Dimmer, 0% to 100%
| 4| | Left-side 4-in-1 LED Color
000 – 007| Off
008 – 024| Red
025 – 041| Green
042 – 058| Blue
059 – 075| White
076 – 092| Yellow
093 – 109| Magenta
110 – 126| Pink
127 – 143| Cyan
144 – 160| Light Green
161 – 177| Lavender
178 – 194| Mauve
195 – 211| Peach
212 – 228| Light Magenta
229 – 245| Ice Blue
246 – 255| Light Pink
|
5
| | Right-side 4-in-1 LED Color
000 – 007| Off
008 – 024| Red
025 – 041| Green
042 – 058| Blue
059 – 075| White
CONTINUED ON NEXT PAGE
Eliminator Furious Five RG – DMX Traits
Software Version 2.0
CHANNEL| DMX VALUE| DESCRIPTION
11-CH MODE| 24-CH MODE
| 5 (cont from prev page)| | Right-side 4-in-1 LED Color (cont from prev
page)
076 – 092| Yellow
093 – 109| Magenta
110 – 126| Pink
127 – 143| Cyan
144 – 160| Light Green
161 – 177| Lavender
178 – 194| Mauve
195 – 211| Peach
212 – 228| Light Magenta
229 – 245| Ice Blue
246 – 255| Light Pink
1| 6| | 4-in-1 LED + UV Show Mode
000 – 007| Off
008 – 045| Jump
046 – 064| Smooth Fade
065 – 083| Fast Pulse
084 – 102| Slow Pulse
103 – 121| Left/Right Jump
122 – 140| Flash
141 – 159| Left/Right Flash
160 – 200| Left/Right Fade
201 – 255| Sound Show
2| 7| 000 – 255| 4-in-1 LED + UV Show Speed , Slow to Fast
3
| | | 4-in-1 LED + UV Strobe
000 – 007| Off
008 – 255| Strobe, Slow to Fast
| 8| 000 – 255| White LED Dimmer , 0% to 100%
CONTINUED ON NEXT PAGE
Eliminator Furious Five RG – DMX Traits
Software Version 2.0
CHANNEL| DMX VALUE| DESCRIPTION
11-CH MODE| 24-CH MODE
6| 9| | White LED Strobe
000 – 007| Off
008 – 255| Strobe, Slow to Fast
4| 10| | White LED Show Mode
000 – 007| Off
008 – 200| Auto Show
201 – 255| Sound Show
5| 11| 000 – 255| White LED Auto Show Speed , Slow to Fast
| 12| 000 – 255| LED Spot Dimmer , 0% to 100%
9| 13| | LED Spot Strobe
000 – 007| Off
008 – 255| Strobe, Slow to Fast
| 14| | Left LED Spot, Outboard Color
000 – 007| Off
008 – 024| Red
025 – 041| Green
042 – 058| Blue
059 – 075| White
076 – 092| Red + Green
093 – 109| Red + Blue
110 – 126| Red + White
127 – 143| Green + Blue
144 – 160| Green + White
161 – 177| Blue + White
178 – 194| Red + Green + Blue
195 – 211| Red + Green + White
212 – 228| Red + Blue + White
229 – 245| Green + Blue + White
246 – 255| Red + Green + Blue + White
CONTINUED ON NEXT PAGE
Eliminator Furious Five RG – DMX Traits
Software Version 2.0
CHANNEL| DMX VALUE| DESCRIPTION
11-CH MODE| 24-CH MODE
| 15| | Left LED Spot, Inboard Color
000 – 007| Off
008 – 024| Red
025 – 041| Green
042 – 058| Blue
059 – 075| White
076 – 092| Red + Green
093 – 109| Red + Blue
110 – 126| Red + White
127 – 143| Green + Blue
144 – 160| Green + White
161 – 177| Blue + White
178 – 194| Red + Green + Blue
195 – 211| Red + Green + White
212 – 228| Red + Blue + White
229 – 245| Green + Blue + White
246 – 255| Red + Green + Blue + White
| 16| | Right LED Spot, Inboard Color
000 – 007| Off
008 – 024| Red
025 – 041| Green
042 – 058| Blue
059 – 075| White
076 – 092| Red + Green
093 – 109| Red + Blue
110 – 126| Red + White
127 – 143| Green + Blue
144 – 160| Green + White
161 – 177| Blue + White
178 – 194| Red + Green + Blue
CONTINUED ON NEXT PAGE
Eliminator Furious Five RG – DMX Traits
Software Version 2.0
CHANNEL| DMX VALUE| DESCRIPTION
11-CH MODE| 24-CH MODE
| 16 (contd from prev page)| | Right LED Spot, Inboard Color (contd from
prev page)
195 – 211| Red + Green + White
212 – 228| Red + Blue + White
229 – 245| Green + Blue + White
246 – 255| Red + Green + Blue + White
| 17| | Right LED Spot, Outboard Color
000 – 007| Off
008 – 024| Red
025 – 041| Green
042 – 058| Blue
059 – 075| White
076 – 092| Red + Green
093 – 109| Red + Blue
110 – 126| Red + White
127 – 143| Green + Blue
144 – 160| Green + White
161 – 177| Blue + White
178 – 194| Red + Green + Blue
195 – 211| Red + Green + White
212 – 228| Red + Blue + White
229 – 245| Green + Blue + White
246 – 255| Red + Green + Blue + White
7| 18| | LED Spot Show Mode
000 – 007| Off
008 – 034| Both LED Spots, Single Color Full Display
035 – 061| Both LED Spots, Single Color Half Display
062 – 088| Both LED Spots, Contrasting Single Color Half Display
089 – 115| Alternating LED Spots, Single Color Half Display
116 – 142| Alternating LED Spots, Single Color Full Display
CONTINUED ON NEXT PAGE
Eliminator Furious Five RG – DMX Traits
Software Version 2.0
CHANNEL| DMX VALUE| DESCRIPTION
11-CH MODE| 24-CH MODE
7 (contd from prev page)| 18 (contd from prev page)| | LED Spot Show Mode
(contd from prev page)
143 – 160| Alternating LED Spots, Pinwheel
161 – 178| Both LED Spots, Pinwheel
179 – 187| Both LED Spots, Single/Dual/Triple/All Color Spin
188 – 200| Both LED Spots, All Color Spin
201 – 255| Sound Show
8| 19| 000 – 255| Auto LED Spot Show Speed , Slow to Fast
| 20| | Red Laser
000 – 127| Off
128 – 255| On
| 21| | Green Laser
000 – 127| Off
128 – 255| On
| 22| | Laser Movement
000 – 010| Off
011 – 120| Counter Clockwise, Fast to Slow
121 – 134| Off
135 – 245| Clockwise, Slow to Fast
246 – 255| Off
10| 23| | Laser Show Mode
000 – 007| Off
008 – 200| Auto
201 – 255| Sound Show
11| 24| 000 – 255| Auto Laser Show Speed , Slow to Fast
IR REMOTE OPERATION
UP/DOWN ARROW: Scrolls through Auto Modes and Sound Modes, or adjusts
intensity for Red, Green, Blue, White, or UV lighting display modes.
OFF: Switches all lighting displays off.
ON: Switches lighting displays on.
R : Turns 4-in-1 LEDs on in Red light mode.
G: Turns 4-in-1 LEDs on in Greenlight mode.
B: Turns 4-in-1 LEDs on in Blue light mode .
W: Turns 4-in-1 LEDs on in White light mode.
A: No function. UV: Turns UV lights on.
0: Switches fixture to AUT1 Mode (Red/Green Laser Auto Show).
AUTO: Switches fixture to more recently used Auto Mode. Up/Down Arrow
buttons can be used to cycle through the different Auto Modes.
STROBE: Switches the fixture to AUT2 Mode (5730 White LED Auto Show).
FADE: Switches the fixture to AUT0 Mode (Full System Auto Show).
SOUND: Switches the fixture to the most recently used Sound Mode. Up/Down
Arrow buttons can be used to cycle through the different Sound Modes. 1-9
NUMBER PAD: Switches 4-in-1 LEDs to one of nine colors presets. Note that the
display color corresponds approximately to the color of the button on the
remote, but does not match precisely.
Please note that the device may also be affected by other IR devices
operating nearby, and those devices may likewise be affected by this IR
remote, regardless of whether those devices were produced by Eliminator
Lighting or by another manufacturer.
To minimize the chances of interference, it is highly advisable to test your
setup ahead of time to ensure that each IR remote compatible device is located
well outside the range of any other IR remote compatible devices that have
been installed in the vicinity.
DIMENSIONAL DRAWINGS
NOTE: Dimensions may not be drawn to scale. 22
SPECIFICATIONS
- Strobe: 81 SMD 5730 white LED
- Four (4) 3W UV CREE single color
- Six (6) 3W Quad (RGBW) LEDs
- Laser Diodes: Red = 100MW and Green = 70MW
- Moonflower effect: 5mm LED (16x Red, 12x Green, 12x Blue 12, 16x White)
- 4 operation modes: Automatic running, DMX, Sound Active, and Master/Slave
- Sound controlled via a built-in microphone
- 0-100% linear dimmer
- Power Consumption: 60W
- 2 DMX Channel modes: 11 or 24 channels
- Voltage: AC110-240V 50/60Hz
- Unit Dimensions (LxWxH): 18″ x 7″ x 6.5″
- Weight: 8 lbs.
- CE Certified
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>