ELIMINATOR LIGHTING EM8 8 Inch Mirror Ball Instruction Manual

ELIMINATOR LIGHTING EM8 8 Inch Mirror Ball

Product Information

Specifications

• Brand: Eliminator Lighting
• Model: EM-8
• Location: Los Angeles, CA. / Kerkrade, The Netherlands / Lerma, Mexico
• Website:www.adj.com
• Email:info@adj.com

Product Usage Instructions

Safety Guidelines

It is important to follow safety guidelines to prevent any damages or injuries:

• Keep flammable materials away from the device.
• Use the product indoors or in dry locations only; do not expose it to rain or moisture.
• Avoid looking directly into the reflected light source to prevent retina injury.
• Sensitive persons may suffer an epileptic shock from the light, so use it with caution.

Maintenance Guidelines

To ensure the safe operation of the product, follow these maintenance guidelines:

• Regularly inspect and maintain rigging points to prevent accidents.
• Ensure all rigging is secure to avoid injury from falling devices.

Installation Guidelines

When installing the EM-8, please adhere to the following guidelines:

• Keep the device at least 5.0 ft (1.5m) away from flammable materials and pyrotechnics.

Frequently Asked Questions (FAQ)

Q: Can I use the EM-8 outdoors?

• A: No, the product is designed for indoor/dry locations only to prevent damage from exposure to rain or moisture.

Q: What should I do if I notice damaged rigging points?

• A: If you notice damaged rigging points, do not use the device and contact customer support for assistance.
• Using the product with damaged rigging points can lead to accidents.

GENERAL INFORMATION

INTRODUCTION

• Please read and understand all instructions in this manual carefully and thoroughly before attempting to operate this product.
• These instructions contain important safety and use information.

UNPACKING

This device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect the unit for damage and be sure all accessories necessary to operate the unit have arrived intact. In the event, that damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this kit to your dealer without first contacting customer support at the number listed below. Please do not discard the shipping carton in the trash. Please recycle whenever possible.

CUSTOMER SUPPORT

• Tel: 323-213-4592 | Fax: 323-582-2941
• www.adj.com
• support@eliminatorlighting.com

WARRANTY RETURNS

• All returned service items, whether under warranty or not, must be freight pre-paid and accompanied by a return authorization (R.A.) number.
• The R.A. number must be written on the outside of the return package.
• A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container.
• If the unit is under warranty, you must provide a copy of your proof of purchase invoice.
• Items returned without an R.A. number marked on the outside of the package will be refused and returned at the customer’s expense.
• You may obtain an R.A. number by contacting customer support.

LIMITED WARRANTY (USA ONLY)

• A. Eliminator Lighting, an ADJ Products, LLC brand, hereby warrants, to the original purchaser, Eliminator Lighting products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
• B. For warranty service, you must obtain a Return Authorization number (RA#) before sending back the product contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the Eliminator Lighting factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Eliminator Lighting will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, Eliminator Lighting shall have no liability whatsoever for loss of or damage to any such accessories, or for the safe return thereof.
• C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Eliminator Lighting concludes, after inspection, affects the reliability of the product, if the product has been repaired or serviced by anyone other than ADJ Products, LLC factory unless prior written authorization was issued to purchaser by Eliminator Lighting; if the product is damaged because not properly maintained as outlined in the instruction manual.
• D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic check-ups. During the period specified above, Eliminator Lighting will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor because of defects in material or workmanship. The sole responsibility of Eliminator Lighting under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Eliminator Lighting. All products covered by this warranty were manufactured after August 15, 2012, and bear identifying marks to that effect.
• E. Eliminator Lighting reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
• F. No warranty, whether expressed or implied, is given or made to any accessory supplied with the products described above. Except to the extent prohibited by applicable law, all implied warranties made by Eliminator Lighting in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Eliminator Lighting be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use this product.
• G. This warranty is the only written warranty applicable to Eliminator Lighting products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

LIMITED WARRANTY PERIODS

• All Eliminator Lighting products (except laser diodes) = 1-year (365 days) Limited Warranty (Such as Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands, etc. excluding LED and lamps)
• Laser Products = 1 Year (365 Days) Limited Warranty (excludes laser diodes which have a 6-month limited warranty)
• Batteries = 180-Day Limited Warranty (excluding batteries which have a 180-day limited warranty)

SAFETY GUIDELINES

• To guarantee a smooth operation, it is important to follow all instructions and guidelines in this man-ual.
• ELIMINATOR LIGHTING is not responsible for injury and/or damages resulting from the misuse of these devices due to the disregard of the information printed in this manual.
• Only qualified and/or certified personnel should install these devices and only the original rigging parts included with these devices should be used for installation.
• Any modifications to these devices and/or the included mounting hardware will void the original manufacturer’s warranty and increase the risk of damage and/or personal injury.
• DAMAGES RESULTING FROM MODIFICATIONS TO THIS DEVICE AND/OR THE DISREGARD OF SAFETY GUIDELINES IN THIS MANUAL VOID THE MANUFACTUR-ER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS
• AND/OR REPAIRS.
• KEEP FLAMMABLE MATERIALS AWAY FROM THIS DEVICE!
• INDOOR / DRY LOCATIONS ONLY!
  • DO NOT EXPOSE TO RAIN AND / OR MOISTURE!
• NEVER LOOK DIRECTLY INTO THE REFLECTED LIGHT SOURCE!
  • RETINA INJURY RISK – MAY INDUCE BLINDNESS!
  • SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
• DO NOT position the device close to any FLAMMABLE MATERIALS while operating.
• DO NOT attempt installation and/or operation of devices if you lack the relevant knowledge.
• DO NOT permit operation by persons who are not qualified to operate these types of devices.
• DO NOT shake devices, and avoid brute force when installing and/or operating.
• DO NOT remove or disassemble devices, as there are NO user-serviceable parts inside.
• ALWAYS disconnect devices from a main power source (not included) before performing any cleaning.
• ALWAYS wear gloves when handling the mirror ball.
• ALWAYS be careful when handling the mirror ball, as damaged mirror panels can cause cuts and other injuries.
• Only use the recommended rigging hardware as described in this guide.
• Use only the original packaging and materials to transport these devices for service.

MAINTENANCE GUIDELINES

CLEANING

• Frequent cleaning is recommended to ensure proper function, optimized light output, and an extended life.
• The frequency of cleaning depends on the environment that the device operates in damp, smoky, or particularly dirty environments can cause a greater accumulation of dirt on the mirrored surface.
• Clean the external surface periodically with a soft, dry cloth to avoid dirt/debris accumulation.
• NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

• Regular inspections are recommended to ensure proper function and extended life. There are no user-serviceable parts inside these devices.
• Please refer all other service issues to Eliminator Lighting. Should you need any spare parts, please order genuine parts from Eliminator Lighting.

Please refer to the following points during routine inspections:

• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during normal operation, resulting in damage or injury as larger parts could fall.
• Check for any deformations on the mirrored ball, rigging hardware, and rigging points (ceiling, suspension, trussing. etc.) Damaged rigging points or unsecured rigging could cause the devices to fall and seriously injure a person(s).

OVERVIEW

INSTALLATION GUIDELINES

FLAMMABLE MATERIAL WARNING

• Keep devices at least 5.0 ft (1.5m) away from flammable materials and/or pyrotechnics.

• DO NOT INSTALL THE DEVICE IF YOU LACK THE RELEVANT QUALIFICATIONS!

• OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, INCLUDING BUT NOT LIMITED TO CALCULATING WORKING LOAD LIMITS, KNOWLEDGE OF INSTALLATION MATERIAL BEING USED, AND PERIODIC SAFETY INSPECTION OF ALL INSTALLATION MATERIAL. IF YOU LACK THESE QUALIFICATIONS, DO NOT ATTEMPT TO PERFORM THE INSTALLATION YOURSELF.

• IMPROPER INSTALLATION CAN RESULT IN BODILY INJURY!

• BEFORE RIGGING/MOUNTING DEVICES TO ANY METAL TRUSS/STRUCTURE OR CEILING, A PROFESSIONAL EQUIPMENT INSTALLER MUST BE CONSULTED TO DETERMINE IF THE METAL TRUSS/STRUCTURE OR CEILING IS PROPERLY CERTIFIED TO SAFELY HOLD THE COMBINED WEIGHT OF THE FIXTURE, CLAMPS, CABLES, AND ACCESSORIES.

• BEFORE MOUNTING DEVICES TO ANY SURFACE OR STRUCTURE, MAKE SURE THE SUR-FACE OR STRUCTURE CAN HOLD A MINIMUM POINT LOAD OF 10 TIMES THE WEIGHT OF THE DEVICES.

• FOR ADDED PROTECTION, INSTALL DEVICES AWAY FROM WALKING PATHS, SEATING AR-EAS, OR AREAS WHERE UNAUTHORIZED PERSONNEL CAN REACH THE DEVICES.
  NEVER STAND DIRECTLY BELOW THE DEVICES WHEN MOUNTING, REMOVING OR SERVICING.

• DEVICES MUST ALL BE INSTALLED FOLLOWING ALL LOCAL, NATIONAL, AND COUNTRY COMMERCIAL ELECTRICAL AND CONSTRUCTION CODES AND REGULATIONS.

• The mirror ball unit features a mounting eyelet, which is located at the center of the top of the mirror ball. This eyelet should be used as the primary mounting point. Please refer to the Overview section of this manual.

• Mounting hardware (such as chains or carabiners) should be rated to support 12 times the weight of the unit.

• When installing the mirror ball in a rotating display, make sure to mount the mirror ball in such a way that the mounting cables or chains do not become tangled as the mirror ball rotates.

• Installation should NEVER be done using hardware constructed of an abrasive material, as this could lead to excessive wear on the mounting eyelets.

• Always ensure that the unit is firmly fixed to avoid vibration and slipping during operation.

• Always ensure that the structure to which you are attaching the unit is secure and can support at least 10 times the unit’s weight. Additionally, always use a mounting cable that can hold 12 times the weight of the unit when installing the fixture.

• The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of the general public.

• It is strongly advised that installation should be performed by multiple individuals, as the bulky nature of the unit may require two hands for support during installation.

• Always wear gloves when handling the mirror ball to avoid leaving fingerprints on the mirrors, and to protect yourself against broken mirror pieces.

• NEVER install a mirror ball with damaged mirror pieces, as these could come loose and fall during operation and cause serious injury!

• If damage is found on the mirror ball, contact Eliminator Lighting for repair services.

CABLE ATTACHMENT

• To install, attach a mounting cable or chain to the mirror ball eyelet using a link or carabiner that has been rated to support the weight of the mirror ball, as shown below.
• Attach the other end of the mounting cable or chain to a mounting point that has been rated to support at least 12 times the combined weight of the mirror ball and any associated accessories.
• If installing a mirror ball motor, switch the motor on after the mounting cable or chain has been connected, and confirm that the mirror ball can rotate freely and without obstruction.

LIGHTING THE MIRROR BALL

• Experiment with different angles and distances to achieve the desired result.

FREQUENTLY ASKED QUESTIONS

Can the EM-8 be mounted to a ceiling?

• Yes, it may be installed onto a flat ceiling surface that can support 12 times the combined total weight of the attached mirror ball, motor, and any mounting accessories.
• Careful planning must be used when calculating the combined weight and determining whether the flat ceiling surface can support the weight of the motor and mirror ball. PLEASE CONSULT A PROFESSIONAL FOR CEILING INSTALLATION GUIDANCE!

Is a light included with the EM-8?

• No. However, a variety of lighting fixtures, options, and kits are available for purchase at www.adj.com.

What method should be used to clean the mirror ball?

• Clean the external of the mirror ball surface periodically with a soft cloth to avoid dirt/debris accumulation. NEVER use alcohol, solvents, or ammonia-based cleaners.

Is the mirror ball available in other sizes?

• Yes, Eliminator offers mirror balls in a variety of sizes. Please visit our website for more details.

SPECIFICATIONS

• Model: EM-8
• Dimensions:
• Mirror Ball Body: 8” (203mm)
• Overall Height Including Eyelet: 9” (228mm
• Eyelet Outer Diameter: 1.1” (28mm)
• Weight: 1.4 lbs / 0.63 kg

DIMENSIONAL DRAWINGS

• ©2023 Eliminator Lighting all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. Eliminator logo and identifying product names and numbers herein are trademarks of Eliminator
• Lighting. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-Eliminator brands and product names are trademarks or registered trademarks of their respective companies.
• Eliminator Lighting and all affiliated companies hereby disclaim all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and opera-tion of this product.

Eliminator Lighting

• 6122 S. Eastern Ave. Los Angeles, CA. 90040
• 323-582-2650
• Fax323-532-2941
• www.adj.com
• info@adj.com
• ADJ SUPPLY Europe B.V
• Junostraat 2 6468 EW Kerkrade, The Netherlands
• +31 (0)45 546 85 00
• Fax +31 45 546 85 99
• www.americandj.eu
• info@americandj.eu

ADJ PRODUCTS GROUP Mexico

• AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000+52 728-282-7070

DOCUMENT VERSION

• Due to additional product features and/or enhancements, an updated version of this document may be available online.
• Please check www.adj.com for the latest revision/update of this manual before beginning installation and/or programming.

Date| Document Version| Software Version >| DMX Channel Mode| Notes
---|---|---|---|---
02/11/20| 1.0| N/A| N/A| Initial release
09/08/23| 1.1| N/A| N/A| Updated Overview, Installation Guidelines, FAQs

References

• Home
• ADJ Supply Europe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>