Litever B0BFR82GBH AC Wall Dimmer Compatible Under Cabinet LED Lighting Kit User Manual

Litever B0BFR82GBH AC Wall Dimmer Compatible Under Cabinet LED Lighting

Kit

AC Wall Dimmer Compatible Under Cabinet LED Lighting Kit User Manual (6

-Light-Bar-Kit)

• Thank you very much for buying Litever Under Cabinet LED Lighting Kit.
• We hope this product can make your life “brighter”.
• Before installation, pis kindly read this User Manual carefully, to make sure the installation is safe and easy.
• If any questions or suggestion , pis feel free to contact Litever through Amazon Buyer-Seller Messages with your Order Number.

What Shall Be in the Box ?

• If anything in the left picture missing in the box you received, or less quantity than what the picture shows, pis kindly contact us through Amazon Buyer-Seller Messages with your Order Number.
• We will send the missing parts to you by expedited express at our cost.

AC Wall Dimmer Compatible Under Cabinet LED Lighting Kit Product

Specification

Part: TD-A

• What’s Each Part For & Attention Needed for Each Part
  • LED driver to convert U0VAC into 12VDC to feed the LED light bars. It’s compatible with many in-wall AC dimmers from different brands. It’s also workable with Litever DC12V PWM LED dimmer, instead of AC in-wall dimmers.
  • Caution : Cut off the power, before you hardwire or plug the LED driver.
  • Caution : Input of the LED driver is 100N130VAC.
  • Input voltage over 130VAC (i.e, 220VAC) will damage the LED driver in seconds,
  • Caution : The LED driver is NOT waterproof. It can be used in wet environment but not outdoor environment with rains, direct sunshine.
  • Caution : The surface temperature of this LED driver can reach SSN6o•c, when it’s working at full load.
  • DO NOT touch it when it’s working to avoid being hurt. DO NOT cover the LED driver or put the LED driver inside a very small sealed box without ventilation.
  • Caution: Pis do NOT put it near ovens, grills or any environment with high temperature.
  • caution : This LED driver is designed to work less than 12 hours per day.
  • Do not make it work continuously without stop.
  • caution : This LED driver has a minimum power load of 5%.
  • That means, the minum power consuption of your LED lights shall be so Watt*5%=2.5 Watt.
  • Caution : Pis do NOT over load the LED driver. Overloading may lead to premature failure or even danger of fire. Pis refer to “Recommended Layout” part of the User Manual for details.

Part: TD-B 12VDC Input 12″ LED Light Bars

• Caution : Input of these light bars is 12VDC. DO NOT connect LED Light bars to commercial or household electricity (120VAC) directly to  avoid risk of electrical shock and product damage.

• Caution : LED light bar will produce some heat when working. The surface temperature can increase to around 45N6o·c (113N 14o•F )after working for a long time.

  • Do NOT touch the LED light bars when they are working to avoid being hurt.
  • Do NOT install the light bars in a very small sealed box or pipe without ventilation.

• Caution : The LED Light Bars are designed to work at ambient temperature lower than 35•c 35•c is around 95•F. Pis do NOT put them near ovens, grills or environment with high temperature.

• Caution : If any single LED light bar in your connection is NOT working properly, pis kindly un-plug the LED Driver and stop using the whole light kit.
  At the same time, pis kindly contact Litever through Amazon email system ASAP.

• Attention : DO NOT pull the cables on each light bar brutally at any time.  It may lead to loose of the cable.

• Tips : Pis connect each light bar and the LED dimmer and LED Driver  together to check whether every part is working properly  before the installation.

• Tips : There is a thin layer of film on the milky cover of each light bar  to protect it.
  We suggest customers peal off this thin film after installation.

• Tips : Pis seal the last open connectors with the “blind end cap” (Part: TD-J).
  Pis do NOT cut off the last open connetors directly to avoid possible electrical short.

• Tips: Pis check the lable on each light bar for its specification.

Part: TD-E
Extension cables.

• Caution : The extension cable is designed to work at ambient temperature lower than 45•c 45’C is around 113’F.
  Pis do NOT put it near ovens, grills or any environment with high temperature.

• Attention : DO NOT connect the extension cables lonnger than 6 meters in  one serial connection.
  Otherwise, There will be obvious current/voltage loss and the light bars will be. less bright as it should be.

• Tips : The extension cable is not a must. You can remove them if they are not needed.

Mounting clips and screws

• Tips : We suggest you work out a layout to decide where to install the light bars beforethe installation.
• Tips : Firstly, pis decide where to install the light bar. Secondly, pis fix the mounting clips by the screws. Thirdly, pis make the clips clamp the light bar.
• Self-adhesive pads for fixing the light bars, as an alternative option.
• Tips : If the light bars will be fixed to steel, marble or other surface
  where you do not want to use the screws, you can use the self-adhesive pads.

Tips : Firstly, pis decide where to install the light bar.

• Secondly, pis CLEAN the back of the light bar and make it clean and dry.
• Thirdly, peel off the white layer and apply self-adhesive pads on the back of the light bar.
• Press the back of the self-adhesive pad from one side to the other side to make it firmly stuck.
• We suggest you use 3 pcs self-adhesive pads for one 12″ light bar.
• Fourthly, CLEAN the surface where the self-adhesive pads will be applied to make it dry and clean.
• Fifthly, peel off the red layer of the self-adhesive pads on the back of the light bar.
• Press the light bar gently for firm fixing.

Big cable tiers for fixing the cable to make a clean in stallation.

Tips : Pis clean and dry the surface where the self-adhesive pads will be applied.
The green/white layer on the self-adhesive pads needs to be peeled off for fixing cables.

Small cable tiers for fixing the cable to make a clean installation.

Tips : Pis clean and dry the surface where the self-adhesive pads will be applied.
The green/white layer on the self-adhesive pads needs to be peeled off for fixing cables.

Blind end cap for sealing the last connector.

Tips : Pis seal the last open connectors in each serial connection with blind end caps.

How to Wire the LED Driver to AC Dimmer

• Single Driver Connecting Diagram
• Multiple Drivers Connecting Diagram

Recommended Layouts for Litever 6-Light-Bar Under

Cabinet LED Lighting Kit

• You can add an ON/OFF switch at point@, if you need one.
• Pis kindly search “B09XV9XTTW” on amazon for that Litever ON-OFF switch.
• There are 4 pcs 1 meter extension cables included in the kit.
• If you need extra extension cables, pis kindly search “B096K1DTHC” on amazon. Extension cables can be put at points@/®/©/®/@/(J)/@
• For extra Litever 12″ LED light bars ,pls kindly search “B097H9FPWK” on amazon and choose the light color.
• For 1-to-2 power splitter,pls kindly search “B09JNQYFRF” on amazon.
• For 1-to-3 power splitter ,pls kindly search “B09JVMDJYJ” on amazon.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>