Litever 3 Bars Kit-3000K Under Cabinet LED Light Bar Kits User Manual

*Litever Under Cabinet
LED Lighting Kit
User Maswal (3-Light-Bar-Kit)**

3 Bars Kit-3000K Under Cabinet LED Light Bar Kits

Thank you very much for buying Litever Under Cabinet LED Lighting Kit.
We hope this product can make your tife “brighter”.
Before installation, pis kindly read this User Manual carefully, to make sure the instatlation is safe and easy.
If any questions or problems or suggestions, you can always contact us through Amazon Buyer-Selier- Messages or directly by email:sales@litever.us

What Shall Be in the Box ?

If anything in the le picture missing in the box you received,or less quantity than what the picture shows, pis kindly contactus through Amazon Buyer-Seller- Messages or contact Litever directly at sales@litever.us with your Amazon order number.
We will send the missing parts to you by expedited express.

*Litever Under Cabinet LED Lighting Kit (3-Light-Bar-Kit) Product Specification**

What’s Each Part For & Attention Needed for Each Part Power Adapter to convert 120VAC into 12VDC to feed the LED dimmer and light bars.
Caution: Turn off the outlet or switch, before you plug the power adapter.
Caution: Do NOT touch the AC plugs at any time.
Caution: This power adapter is NOT waterproof. It’s for indoor use only and shall be protected from water or heavy moisture environment or direct sunshine.
Caution: This power adapter will produce some heat when working.
Do not put it in a very small sealed box without ventilation.
Caution: This power adapter is designed to work at ambient temperature lower than 35°C 35°C is around 95 7.
Pis do NOT put it near ovens, grills or any environment with high temperature.
Attention: Pls read the iable on the Power Adapter and follow it’s instructions.
The correct output shall be “OUTPUT: 12V—2A”
If not, pis kindly contact Litever with your Amazon order number.
Attention: This power adapter can load maximum 3 pcs 12VDC Litever 12″ LED light bars.
Overloading may lead to premature failure or even danger of fire.
Attention: This power adapter is NOT compatible with any existing wall dimmers.
However, it is ok with a simple ON/OFF switch without dimming fuction.
Attention: tthe light bars are flashing or nat working properly after correct installation, pls stop using it and contact Litever through Amazon Buyer-Seller-Messages ASAP.
attention: This power adapter is designed to work less than 12 hours per day.
Do not make it work continuously without stop.

PWM LED Dimmer for adjusting the brightness of the light bars and the ON/OFF. Caution: DO NOT connect LED dimmer to commercial or household electricity (120VAC) directly, to avoid risk of electrical shock and product damage.
Caution: This LED dimmer is designed to work at ambient temperature lower than 35 35°C is around 957.
Pis do NOT put it near ovens, grills or any environment with high temperature.
Tips: If you do not need this LED dimmer, it can be removed or replaced by simple Litever ON/OFF switch.
Also, a simple Litever ON/OFF switch can be added before this PWM LED dimmer. For Litever ON/OFF switch, pls search “BO7DXB3LNR” on Amazon
Tips: If the LED dimmer can not work properly, pis kindly contact us through Amazon Buyer-Seller-Messages.
Tips: The self-adhesive pad is for fixing the PWM LED dimmer.
Pls clean and dry the mounting surface before applying the self-adhesive pad.
Tips: The LED dimmer may be NOT compatible with some motion sensors.
Tips: pis check the lable on this dimmer for its specification. Caution: Input of these light bars is 12VDC. DO NOT connect LED Light bars to commercial or household electricity (120VAC) directly to avoid risk of electrical shock and product damage.
Caution: LED light bar will produce some heat when working. The surface temperature can increase to around 45°60’°C (113°140′) after working for a long time.
Do NOT touch the LED light bars when they are working to avoid being hurt.
Do NOT install the light bars in a very small sealed box or pipe without ventilation.
Caution: The LED Light Bars are designed to work at ambient temperature lower than 35°C 35°C is around 95¥.
Pis do NOT put them near ovens, grills or environment with high temperature.
Caution: If any single LED light bar in your connection is NOT working properly, pls kindly remove that light bar un-plug the power adapter and stop using the whole light kit.
At the same time, pls kindly contact Litever through Amazon Buyer-Seller- Messages ASAP.
Attention: The light bars are NOT waterproof and shall be protected from direct water and heavy mositure environment.
Attention: DO NOT pull the cables on each light bar brutally at any time.
It may lead to loose of the cable.
Tips: Pls connect each light bar and the LED dimmer and power adapter together to check whether every part is working properly before the installation.
Tips: There is a thin layer of film on the mitky cover of each light bar to protect it.
We suggest customers peal off this thin film after installation.
Tips: Pls seal the last open connectors with the “blind end cap”(Part: J).
Pils do NOT cut off the last open connetors directly to avoid possible electrical short.
Tips: Pls check the lable on each light bar for its specification.

  Caution: The extension cable is designed to work at ambient temperature lower than 45°C 45° is around 1137.
Pts do NOT put it near ovens, grills or any environment with high temperature.
Attention: DO NOT connect the extension cables lonnger than 6 meters in one serial connection.
There wilt be obvious current/voltage loss and the light bars there will be less bright as it should be.
Tips: The extension cable is not a must. You can remove them if they are not needed.

Tips: we suggest you work out a layout to decide where to install the light bars before the installation,
Tips: Firstly, pis decide where to install the light bar.
Secondly, pts fix the mounting clips by the screws.
Thirdly, pis make the clips clamp the light bar.

Self-adhesive pads for fixing the light bars,as an alternative option. Tips: If the light bars will be fixed to steel, marble or other surface where you do not want to use the screws,
you can use the self-adhesive pads.
Tips: Firstly, pls decide where to install the light bar.
Secondly, pis CLEAN the back of the light bar and make it clean and dry.
Thirdly, peel off the white layer and apply self-adhesive pads on the back of the light bar.
Press the back of the self-adhesive pad from one side to the other side to make it firmly stuck.
We suggest you use 3 pcs self-adhesive pads for one 12” tight bar.
Fourthly, CLEAN the surface where the self-adhesive pads will be applied to make it dry and dean.
Fifthty, peel off the red layer of the self-adhesive pads on the back of the light bar.
Press the light bar gently for firm fixing.

Big cable tiers for fixing the cable to make a clean installation.

Tips: Pls clean and dry the surface where the self-adhesive pads will be applied.
The green/white layer on the self-adhesive pads needs to be peeled off for fixing cables.

Small cable tiers for fixing the cable to make a clean installation. Tips: Pls clean and dry the surface where the self-adhesive pads will be applied.
The green/white layer on the self-adhesive pads needs to be peeled off for fixing cables.

Blind end cap for sealing the last connector. Tips: Pls seal the last open connectors in each serial connection with blind end caps.

Recommended  Layout

You can add an ON/OFF switch at point 11) Pis search “BO7DXB3LNR” on Amazon for it.
You can also replace the dimmer directly with that ON/OFF switch
Extension cables can be added at point ①/②/③/④/⑤ We suggest total length of all extension cables less than 6 meters
If you like,the LED dimmers,can be put at point ‘3: or ‘4; or both.
Litever 6″ light bars available for small cabinets narrow than 12″.
Pls search “BO7V8RV885″ on Amazon.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>