Litever LL-029-RGBW-3000K-12 Under Cabinet LED Lighting Kit. RGB Color and Bright Warm User Manual

Litever LL-029-RGBW-3000K-12 Under Cabinet LED Lighting Kit. RGB Color and Bright Warm User Manual

‘Thank you very much for buying Litever Under Cabinet LED Lighting Kit. Ve hope this product can make your life “brighter” & “colorful* Before installation, pls kindly read this User Manual carefully, to make sure the installation s safe and easy.

If any questions or problems or suggestion, you can always contact Litever through Amazon Buyer-Seller Messages with your Order Number.

What Shall Be in the Box ?

If anything in the left picture missing in the box you received, or less quantity than the picture shows, pls kindly contact Litever through Amazon Buyer-Seller-Messages.

We will send the missing parts to you by expedited express at our cost.

• 12.75° RGBW LED bar X6,
  
  

• Power adapter X 1
  
  

• **RGBW controller x1

**

• **Self adhesive pads x 18

**

• **50CM RGBW extension cable x 5

**

• **AAA battery x 2

**

• **Cable tie mount x 18

**

• **Cable clips x 16

**

• Big self adhesive pads x 12
  

• Mourting Screws X 12
  

• **Mourting 6ps X 12

**

Frequently Asked Questions

Q: Why the controller does NOT respond to the remote ?

A:

1. Check your power supply to the controller.
   When the power supply is working, there is a green indication light showing that.

2. Check your remote.
   Normally, if the 2 pcs AAA batteries are correctly Installed, when you press any button on the remote, you can see ‘aminor red indication light on the remote.

3. Check the ID numbers marked on the controller and remote.
   When you receive the product, there is an ID number (i, 1D:22256) marked o the remote and the same 1D number will be marked on the controller too. Ifthe ID numbers are different, the controller (i.¢, ID:22256) will NOT reponsond to the remote (i.e, ID:87652) directly.In case of this, pis kindly do the following to “MATCH CODE”:

Step A: CUT OFF the power to ALL the Litever LED controllers you have in your house. (Pls kindly note that pressing “OFF” on the remote is NOT “CUT OFF the power”. You need to separate/ disconnect the controller and power supply physically).

Step B: Wait for at least 10 seconds. ‘Then, turn ON the power to the controller (ID:22256) only and KEEP pressing “ON” button on the remate (ID:87652) IMMEDIATELY (within 3 seconds of turning on the power). Ifthe lights after the controller (1D522256) flash 3 times slowly, that means “MATCH CODE” is successful.

Step C: Normally, the controller (1D:22256) will respond to the remote (ID:87652) after the above steps. 1f NOT, pls kindly repeat the Step A & Step B again.

Q: Can 1 remote controls 2 or 3 or more controllers simultaneously ?

A: No, when you receive the product. When you receive the product, normally, the remote (i.e, ID:24434) can only control the controller marked with the same 1D number. However, if you want the remote (i.e, ID:24434) to control controllers with different ID numbers. (i.e, 1D: 38772; 1D: 65665;) from other package boxes simultaneously, pis dothe following to “CLEAR CODE”

Step 1: CUT OFF the power to ALL the Litever LED controllers you have in your house. Wait for at least 10 seconds. Then,tum ON the power to the controller (1D:24434) only and KEEP pressing “ON” button on the remote (ID: 24434) IMMEDIATELY (within 3 seconds of turing on the power). 1f the lights after the controller (D:24434) flash 6 times quickly, that means *CLEAR CODE’is successful

Step2: CUT OFF the power to ALL the Litever LED controllers you have in your house. Wait for at least 10 seconds. Then, turn ON the power to the controller (D:38772) only and KEEP pressing “ON” button on the remote (ID: 38772) IMMEDIATELY (within 3 seconds of turning on the power). Ifthe lights after the controller (1D:38772) flash 6 times quickly, that means “CLEAR CODE’is successful

Step3: CUT OFF the power to ALL the Litever LED controllers you have in your house. Wait for at least 10 seconds. ‘Then, turn ON the power to the controller (ID:65665) only and KEEP pressing “ON button on the remote (ID: 65665) IMMEDIATELY (within 3 seconds of turning on the power). Ifthe lights after the controller (ID:65665) flash 6 times quickly, that means “CLEAR CODE” is successful.

Step 4: Then, you can use ANY of the 3 remotes to control the 3 controllers simultaneously.

Q: I did the above steps. However, right now, 4434), controls controller (1 4434) only. T want remote (ID:; How to do that ?

A: Pls do the following steps to “MATCH CODE”:

Step1: CUT OFF the power to ALL the Litever LED controllers you have in your house. Wait for at least 10 seconds. Then, tum ON the power to the controller (D:24434) only and KEEP pressing “ON” button on the remote (ID: 24434) IMMEDIATELY (within 3 seconds of tuming on the power). TFthelights after the controller (ID:24434) flash 3 times slowly, that means “MATCH CODE” s successful

Step2: CUT OFF the power to ALL the Litever LED controllers you have in your house. Wait for at least 10 seconds. ‘Then,tum ON the power to the controller (D:38772) only and KEEP pressing ON button on the remote. (ID: 38772) IMMEDIATELY (within 3 seconds of tuming on the power). Ifthe lights after the controller (ID:38772) flash 3 times slowly, that means “MATCH CODE’is successful.

Step3: CUT OFF the power to ALL the Litever LED controllers you have in your house. Wait for at least 10 seconds. ‘Then,tum ON the power to the controller (ID:65665) only and KEEP pressing “ON” button on the remote. (ID: 65665) IMMEDIATELY (within 3 seconds of turning on the power). Ifthe lights after the controller (ID:65665) flash 3 times slowly, that means “MATCH CODE” is successful.Step1: CUT OFF the power to ALL the L

Step 4: Then, the controller (ID: 24434) will respond to remote (ID: 24434) ONLY.
the controller (ID: 38772) will respond to remote (ID: 38772) ONLY.
the controller (ID: 65665) will respond to remote (D: 65665) ONLY.

Q: Can I have both white light and colored light on the same light bar simultaneously ?

A: No. There is no such setting in the controller.

Q: Can I have red, blue, green light working together ?

A: No. There is no such setting in the controller.

Power Adapter to convert 120VAC into 12VDC to feed the LED controller and

light bars.

**Part: A

Caution: Turn off the outlet or switch, before you plug the power adapter.
Caution: Do NOT touch the AC plugs at any time.
Caution: This power adapter is NOT waterproof. It for indoor use only and shall
protected from water or heavy moisture environment or direct sunshine.
Caution:** This power adapter will produce some heat when working.
Do not put itin a very small sealed box without ventilation.
This power adapter is designed to work at ambient temperature lower than 35°C 35°C is around 95°F

Attention: Pls do NOT put it near ovens, grills or any environment with high temperature. Pis read the lable on the Power Adapter and follow it’s instructions. The correct output shall be “OUTPUT :12V—3A”If not, pis kindly contact Litever with your Amazon order number.

Attention: Overloading may lead to premature failure or even danger of fire.
Pis refer to “Recommended Layout” part for details.

Attention: This power adapter is NOT compatible with any existing wall dimmers.
However, itis ok with a simple ON/OFF switch without dimming fuction

Attention: If the light bars are flashing or not working properly after correct installation, pls stop using it and contact Litever through Amazon Buyer-Seller Messages.

Attention: This power adapter is designed to work less than 12 hours per day.
Do ot make it work continuously without stop.

LED Controller with Remote

Part: B

Caution: DO NOT connect the LED controler to commercial or household electricity (120VAC) directly, to avoid risk of electrical shock and product damage.

Caution: This LED controller is designed to work at ambient temperature lower than 35°C 35°C is around 95°F .
Pls do NOT put it near ovens, grills or any environment with high temperature.

Tips: Pis refer to the User Manual of the controller for detailed specifications.

Tips: The self-adhesive pad is for fixing the LED controller. Pis clean and dry the mounting surface before applying the self- adhesive pad.

12VDC Input 12.75″ RGB+ White LED Light Bar

Part:C

Caution: nput of these light bars is 12VDC. DO NOT connect LED Light bars to commercial or household electricity (120VAC) directly to avoid risk of electrical shock and product damage.

Caution: LED liht bar will procuce some heat when working, The surface temperature can increase to around 40~48°C (104~122FJafter working for a long time. Do NOT touch the LED light bars when they are working to avoid being hurt. Do NOT install the light bars in a very small sealed box or pipe without ventilation.

Caution: The LED light bars are designed to work at ambient temperature lower than 35°C 35°C is around 95°F. PIs do NOT put them near ovens, grills or environment with high temperature.

Caution: 1f any single LED light bar in your connection is NOT working properly, pis Kindly un-plug the power adapter and stop using the whole light kit At the same time, pls kindly contact Litever through Amazon Buyer-Seller Messages

Attention:   DO NOT pull the cables on each light bar brutally at any time. 1t may lead to loose of the cable.

Tips: PIs connect each light bar and the LED controller and power adapter together to check whether every part is working properly before the installation.

Tips: There is a thin layer of film on the milky cover of each light bar to protect it We suggest customers peal of this thin film after instalation.

Tips: Pis check the lable on each light bar for its specification.

Extension cables

Part: D

Caution: ‘The extension cable is designed to work at ambient temperature over than 45°C 45°Cis around 113°F. Pis do  OT put it near ovens, grills or any environment vith high temperature.

Attention: O NOT connect the extension cables lonnger than & meters in one serial connection.
There will be obvious current/voltage loss and the light bars there will be.
less bright as it should be, f the extension cables are longer than 6 meters in one serial run.

Tips: The extension cable is not a must. You can remove them f they are not needed.

Mounting clips and screws

Part: E

Tips: We suggest you work out a layout to decide where to Installthe light bars before the installation.

Tips: Firstly, pis ecide where to install the light bar. ‘Secondly, pls fix the mounting clips by the screws. / Thirdly, pls make the clips clamp the light bar.

Self-adhesive pads for fixing the light bars, as an alternative option.

Part:F

Tips: you do not want to use the screws, you can use the self-adhesive pads. Firstiy, pls decide where to install the light bar. Secondly, pls CLEAN the back of the ight bar and make it clean and dry.

Tips: Thirdly, peel off the white layer and apply self-adhesive pads on the back of the light bar. Press the back of the self-adhesive pad from one side to the other side to make it firmly stuck. We suggest you use 3 pcs self- adhesive pads for one 12.75″ light bar. Fourthly, CLEAN the surface where the self-adhesive pads will be applied to make it dry and clean.
Fifthly, peel off the red layer of the self-adhesive pads on the back of the light bar.
Press the light bar gently for firm fixing,

Big cable tiers for fixing the cable to make a clean installation

Part: G

Tips: Pis clean and dry the surface where the self-adhesive pads will be applied. The green/white layer on the self-adhesive pads needs to be peeled off for fixing cables.

Small cable tiers for fixing the cable to make a clean installation

Part: H

Tips: PIs clean and dry the surface where the self-adhesive pads will be applied. The green/white layer on the self-adhesive pads needs to be peeled off for ’ fixing cables.

Recommended Layout

Layout A

Maximum 10 pcs Litever 12.75″ RGBW LED bars 

Layou B
Maximum 10 pcs Litever 12.75″ RGBW LED bars

This 2-way power splitter is NOT included in the kit. Pls kindly search “BOBFDKDBZT” on amazon to buy that if you need it.

1f you use Layout B, you need to buy a Litever 2-way power splitter. Pls kindly search *BOBFDKDBZT” on amazon for that, 1f you need extra light bars, pls kindly search “BOBC418INT” on amazon and choose the correct light color.
Extension cables can be put at points @/ @/ &/ © /@) There are 5 pcs x S0CM extension cables included in the kit. If you need extra, pls kindly search “BOBFDMHOYW” on amazon. 1 you need extension cables between the power adapter and the controller, pis kindly search “B0S6K1DTHC” onamazon We suggest total length of all extension cables less than 6 meters.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>