MEDIASHOP M31154 Livington Clean Water Spin Mop Instruction Manual

MEDIASHOP M31154 Livington Clean Water Spin Mop

Product Information

Specifications

• Mop plate
• Joint
• Lower handle piece with release lever
• Central handle piece
• Upper handle piece
• Microfibre pad
• Fresh water chamber cover
• Cleaning brush
• Bucket with double-chamber system
• Laminate & tile detergents
• Parquet detergent

Product Usage Instructions

Assembly

1. Press the microfibre pad onto the mop plate, ensuring that it lies flush against the mop plate.
2. Screw the lower handle piece onto the mop head, then tighten the middle and upper parts of the handle. Make sure they are tightly screwed together.

Filling the Fresh Water Chamber (#2-3)

1. Remove the fresh water chamber cover.
2. Fill the chamber with approximately 3 litres of fresh water and a small amount of detergent.
3. Put the cover back on until it clicks into place, ensuring that the cleaning brush aligns with the recess in the fresh water chamber. Do not overfill with water.

Attaching the Pad

Press the smooth white side of the pad against the underside of the mop head.

Wringing out & Moistening the Pad (#4-6)

1. Open the release lever on the handle by tilting it forwards.
2. Place the mop head on the fresh water chamber cover, aligning the hole in the mop head with the raised white part of the cover.
3. Push the handle down and pull it up again, rotating the mop head on the cover and throwing dirty water away.

Frequently Asked Questions (FAQ)

Q: Are the microfibre pads machine washable?

A: Yes, the microfibre pads are machine washable.

Q: What are the washing symbols on the pad?

A: The pad is made of 55% Polyester, 25% Polyurethane, and 20% Nylon.

Delivery contents: Parts and descriptions

1. Mop plate
2. Joint
3. Lower handle piece with release lever
4. Central handle piece
5. Upper handle piece
6. Microfibre pad
7. Fresh water chamber cover
8. Cleaning brush
9. Bucket with double-chamber system
10. Laminate & tile detergents
11. Parquet detergent

SAFETY NOTICES

• Do not use the product if it is in poor condition or defective.
• Keep the product out of reach of children.
• The mop is only intended for domestic use.

Assembly

1. Press the microfibre pad onto the mop plate. Make sure that the pad lies flush against the mop plate (corner to corner). The pad is held in place by means of a Velcro-like fastener.

2. Now screw the lower handle piece onto the mop head. Then tighten the middle and then the upper part of the handle. Make sure that the parts of the stem are screwed tightly together.
   USE
   Filling the fresh water chamber (#2-3)
   

3. Remove the fresh water chamber cover and fill the chamber with approx. 3 litres of fresh water and a small amount of detergent.

4. Put the cover back on until it clicks into place. Make sure that the cleaning brush aligns with the recess in the fresh water chamber.
   Note: Do not overfill with water. The water level must not touch the cover.
   Attaching the pad: Press the smooth white side of the pad against the underside of the mop head.

Wringing out & moistening the pad (#4-6):

1. Opening the release lever: Release the release lever on the handle by tilting it forwards.

2. Place the mop head on the fresh water chamber cover. The hole in the mop head should be placed on the raised white part of the cover.

3. Now push the handle down and pull it up again. The easiest way to do this is to grasp the handle by the upper handle part. The mop
   head now rotates on the cover, and dirty water is thrown to the edge and caught there. Coarse dirt is removed from the pad by the cleaning brush. At the same time, fresh water is sprayed onto the pad.

4. Repeat the process until you are satisfied with the level of moisture in the pad. The more you spin the pad, the more water is pumped up and the wetter the pad gets.
   Note: On first use, it may take a few pumps to moisten the pad.

5. To change, detach the mop head from the bucket, raise the handle to the desired height, and push the release lever back up until it snaps into place.

Adjusting the telescopic rod: You can adjust the lower part of the handle to the length that suits you best. To do this, loosen the release lever, then set the desired length by closing the lever again. Note: The handle rotates when the lever is open. Removing the pad: Simply pull the pad off with your hand to remove it.

Emptying the bucket

Dirty water chamber: First empty the dirty water chamber by opening the valve on the side of the bucket. Alternatively, you can also pour out the bucket. To prevent the fresh water chamber cover from falling off, remove it beforehand. The best way to pour out the bucket is by allowing the dirty water to drain through the strainer.

Fresh water chamber: Remove the cover and pour out the water.

Cleaning note: The mop can be cleaned and dried with a cloth.

MICROFIBRE PAD CARE INSTRUCTIONS
The pads are machine washable.

PAD WASHING SYMBOLS
Material: 55% polyester, 25% polyurethane, 20% nylon

Liability claims against the company MediaShop, which relate to damage (except in the case of injury to life, body or health of a person, so-called personal injuries), material or immaterial in nature, caused by the use or non-use of the information provided or through the use of incorrect and incomplete information provided by third parties is fundamentally excluded, unless it can be proven that MediaShop acted with wilful intent or gross negligence

info.tr@MediaShop-group.com

office@MediaShop-group.com

www.MediaShop.tv

References

• Group Publishing
• MediaShop - Das Original aus dem TV ✓ online bestellen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>