ANYCUBIC B08RZ1C39Q 3D Printer Plant Based Resin User Guide

: June 15, 2024
: Anycubic

Table of Contents

B08RZ1C39Q 3D Printer Plant Based Resin
Specifications
Precautions
Printing Parameters for Printer
Support Setting Suggestions for Slicing Software
Parts Cleaning Operations
Post-curing
Waste Liquid Treatment
FAQ
Read User Manual Online (PDF format)
Download This Manual (PDF format)

B08RZ1C39Q 3D Printer Plant Based Resin

Specifications

Product: Plant-based Resin
Precautions: Please follow the safety guidelines mentioned
below

Precautions

Please handle the resin carefully and avoid direct contact with
skin and eyes. In case of contact, rinse with water immediately and
seek medical attention.
Keep the resin container tightly closed when not in use to
prevent contamination.
Store the resin in a cool and dry place, away from direct
sunlight.
Ensure proper ventilation in the working area and use masks and
gloves during operation to protect against resin and its odor.
Air purifiers are recommended for individuals with sensitivity
to resin fumes.
Transparent/white resin printed parts may yellow during
post-curing. To minimize yellowing, reduce the post-curing
time.

Printing Parameters for Printer

Please refer to the table below for default Anycubic resin
printing parameters:

Printer Type	Printing Parameters
Anycubic	Check the user manual for specific settings

Support Setting Suggestions for Slicing Software

We recommend using Anycubic Photon Workshop, CHITUBOX, or Lychee
(for other compatible devices) for slicing. Follow the tips below
for successful printing:

Start with Medium type support settings for ordinary
parts.
Refer to the support parameters provided by the slicing
software for optimal results.

Parts Cleaning Operations

Follow the instructions below to clean the printed parts:

Use 95+% ethanol/IPA or other effective resin cleaning
solutions.
Option 1: Anycubic Wash & Cure
- Place the parts in the cleaning bucket.
- Put the parts and platform into the Anycubic Wash & Cure
  machine for automated cleaning.
Option 2: Ultrasonic Wash
- Perform ultrasonic vibration cleaning using an appropriate
  device.
Option 3: Free Wash
- Manually clean the parts in a container with a cleaning
  solution.

Post-curing

Post-curing is an important step to ensure the final strength
and stability of the printed parts. Follow the manufacturer’s
guidelines for post-curing time and method.

Waste Liquid Treatment

Dispose of waste liquid in an appropriate manner. Sunlight or UV
lamps can be used to cure and solidify the liquid waste for safe
disposal.

FAQ

The parts are not adhered to the bottom plate (partial/full):
- Increase the exposure time of the bottom layer by 30%.
- Level the equipment molding table according to the manual
  instructions.
The formed part and the support are disconnected from the
support connection:
- In the slicing software, increase the depth of the support
  embedded in the part by 0.5mm.
- Increase the support diameter and adjust the support
  distance/density as needed.
Fault occurs in the entire section of the part:
- Increase the exposure time by 20-30% for normal exposure
  parameters.
- Reduce the platform lifting speed.
Partial fault of part:
- Check if the LCD screen is dirty and clean it with
  alcohol/IPA.
- Inspect the surface of the release film for wear or
  damage.
- Verify the sliced model for any bugs or corrupted files.

Please contact technical support for further assistance and
guidance.

For more guidance, please contact technical support
User Guide for Plant-based Resin
Plant-based Resin contains soybean oil extract as raw material, which can be adapted to light curing equipment in the 365~405 band. It has the advantages of low odor, good rigidity, low shrinkage, good detail performance, and high success rate. It can be used in processing of animation , cultural and creative hand-made models, detailed models, prototype parts, etc. Instructions for use under abnormal temperature conditions: The resin is recommended to be printed in the environment of 25~30. When the surrounding temperature lies in between 15~20, we recommend users to increase the exposure time by 30% from the default setting and reduce the platform lifting speed by 30%.
1. Precautions
(1) Shake the resin bottle/package until well mixed before each print. (2) Check whether there are obvious wrinkles/damages on the FEP film. If so, please replace the FEP film. (3) Check whether there is obvious dirt/excess solid residue on the surface of the LCD screen. If so, please clean it before printing. (4) If the resin has not been used in the 3D printer for more than 3 days, it is recommended to filter the resin with a filter funnel after stirring the resin evenly in the liquid tank, and then pour it back into the resin
1

container.

For more guidance, please contact technical support

(5) Please place the equipment in a well ventilated environment, and

wear masks and gloves during operation. Those PPE can effectively

protect the user from resin and its odor. Air purifier are recommended

for more sensitive user group.

(6) When the transparent/white resin printed parts undergoes

post-curing, their surfaces are more prone to yellowing compared to the

other colored parts. To avoid this, the post-curing time can be

appropriately reduced.

2.Printing parameters for printer

Please check your printer type and brand first. At the table below, you

might find your default Anycubic resin printing parameters matching the

corresponding printer (Currently mainly Anycubic).

2

For more guidance, please contact technical support
We will add more printer types that is popularly used. The data comes from Anycubic Laboratory and is for reference only. Different printing parameters and post-processing processes will led to different results. If you encounter troubles while printing, feel free to contact Anycubic for support. We will try our best. *The processing reference parameters are suitable for the factory calibrated energy state of the specific equipment. Printing parameter must be adjusted accordingly if the UV power setting were changed.
3. Support setting suggestions for slicing software
It is recommended to use Anycubic Photon Workshop or CHITUBOX or Lychee (slicing software for other compatible devices) for slicing. There is a good chance for ordinary parts to be successfully printed if your support settings are based on the following tips. (1) We usually recommend customers to try the “Medium” type support from the start, as shown in the figure below for quick support settings.
3

For more guidance, please contact technical support (2) It is recommended that the depth of the embedded part of the support is 0.5mm, and the support gap is 3mm. (3) If the printed part’s section area is less than or equal to 30% of the processing area of the 3D Printer, the combination of “Medium” + “Light” can be used to complete the support design; if the part’s section area is 30% of the processing area of the equipment, the combination of “Medium” + “Heavy” can be used to complete the support design .

Workshop “Meduium” Support Parameters

CHITUBOX “Meduium”

4

For more guidance, please contact technical support Support Parameters
Printing size 30% of the processing area of the equipment, supported by “Medium” + “Light” combination
Printing format 30% of the processing area of the equipment, supported by “Medium” + “Heavy” combination
4.Parts cleaning operations
(1) It is recommended to use 95+% ethanol/IPA or other effective resin
5

For more guidance, please contact technical support cleaning solvents to clean the residual resin on the printed parts. (2) Do not soak the parts in the cleaning solvent for more than 30 minutes. Swelling and damage might occur for prolonged solvent soaking. (3) After cleaning the parts, use a blower/air gun to remove the residual cleaning solution on the surface of the parts. (4) For complex parts with a large number of cavities, multiple cleaning/surface drying cycles can fully clean the parts. (5) Check if there is still residue resin on the surface of model. If so, please wash it again and dry it again. Cleaning Steps

(1) OPTION 1Anycibuc Wash & Cure

OR

Put the parts into the cleaning bucket cleaning bucket
6

Parts + platform into the

For more guidance, please contact technical support (2)OPTION 2Ultrasonic Wash
Ultrasonic vibration cleaning (3)OPTION 3Free Wash
Manual cleaning in cleaning solution container
5.Post-curing
(1) It usually takes 3~5 minutes of UV post-curing to cure the model surface. When encountering parts with complex structure, the curing time can be appropriately extended. (2) Before post-curing, please make sure that there is neither residue resin nor residue solvent on the surface of printed part (if there is, please clean and dry the model surface first). (3) Please ensure that the surface of the part is dried before curing, which can effectively avoid whitening or excess residue on the surface of the part after curing.
7

For more guidance, please contact technical support
6. Waste liquid treatment
(1) Please DO NOT discharge the cleaning solution directly into the sewer. (2) Put the waste liquid in a transparent container under sunlight/ultraviolet light, wait until the resin inside is completely solidified and precipitated, and then filter out the solid residue. Filtered cleaning solution can be reused. (3) Firstly, the waste IPA/Ethanol can be packed in a transparent container and wait for evaporation. Secondly, place the transparent container under sunlight or ultraviolet light to solidify the remaining resin residue, and then the solid waste can be disposed according to local environmental protection regulations. The fully cured solid waste can be considered as regular plastic waste.

Sunlight/ UV Lamp

Solid Waste

7.FAQ
(1) The parts are not adhered to the bottom plate (partial/full): a. Increase the exposure time of the bottom layer by 30%; b. Level the equipment molding table according to the manual.
8

For more guidance, please contact technical support
(2) The formed part and the support are disconnected from the support connection: In the slicing software, increasing the depth of the support embedded in the part (0.5mm), increase the support diameter, and the support distance/density appropriately .
(3) Fault occurs in the entire section of the part: increase the exposure time by 20~30% for normal exposure parameters, and then reduce the platform lifting speed.
9

For more guidance, please contact technical support (4) Partial fault of part: a. Check whether the LCD screen is dirty, and wipe it with alcohol/IPA in time; b. Check whether there is obvious wear on the surface of the release film. c. Check your sliced model to see if there is a bug or corrupted file.
(5) Leakage of liquid tank: Pour the resin in the liquid tank back into the resin bottle after filtering. Check whether there are sharp solid residues at the bottom of the liquid tank/forming platform surface/LCD screen surface, clean and replace the new release film in time.
(6) Large surface roughness on surface of parts/residual debris in the tank: 1st, reduce the normal exposure parameters by 20~30% or the other appropriate amount. 2nd, filter the resin in the liquid tank before reprint.
10

For more guidance, please contact technical support
(7) Obvious surface texture: a. Check whether the release film of the liquid tank is tight (aging/deterioration of elasticity); b. Reduce the platform lifting speed (30%) or the other suitable amount.
(8) Parts with large sections (solid parts) have local rough surfaces after printing & cleaning: a. Increase the light-off time (such as from 0.5s to
11

For more guidance, please contact technical support 1s); b. Reduce the lifting/lowering speed of the forming platform (30%).
(9) The whole surface exposure layer appears in the printing process: a. Check the slice image of the whole layer in the slice data, and check whether there is any error in the original stl file; b. The LCD printer screen abnormally exposes /DLP light machine exposes: restart the device / contact the after- sales service.
To be continued … (10) For more information, please contact our after-sales/ technical support and keep the problem file data for communication (picture /video /slicing parameter setting/ printing parameter setting).
12

For more guidance, please contact technical support
8.Performance parameters

Parameter

Value

Parameter

Value

Viscosity/mPa.s(25) 150~300 Density/g/cm3

1.05~1.25

Hardness/Shore

Wavelength/nm

365~405

84D

D