BANSA ROSE 3 Blade Ceiling Fan Light LED Integrated User Guide

June 12, 2024
BANSA ROSE

BANSA ROSE 3 Blade Ceiling Fan Light LED Integrated USE AND CARE GUIDE

Safety Information

  1. To reduce the risk of electric shock, ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.
  2.  All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
  3.  The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9 kg). Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs. (15.9 kg) or less”.
  4.  The fan must be mounted with a minimum of 7 ft. (2.1 m) clearance from the trailing edge of the blades to the floor.
  5.  Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.
  6.  Do not place objects in the path of the blades.
  7.  To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.
  8.  Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UI-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
  9.  After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
  10. . All setscrews must be checked and re-tightened where necessary before installation.
    WARNING: To reduce the r do not bend the blade brac Ranges) during assembly o I insert objects in the path of t
    WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.
    WARNING: To reduce the r this fan is NOT sadae for u , controls.
    WARNING: To avoid possib sure that the electricity is to box before starting work. If y , enough &avocet wiring kn contact a licensed electrici
    WARNING: Electrical diagr Optional use of any light kit s , marked suitable for use with
    WARNING: To reduce the r or personal injury. ensure bracket Is supported direct structure or the outlet box m L Fan Support of 35 lbs. (15. the screws provided with th

Warranty

The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser. The supplier also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time.
of shipment from the factory for a period of two years after the date of purchase by the original purchaser correct such defects without charge or at our option replace with a comparable or superior model if the product is returned.
To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and re-installing the product are your responsibility. Damage to any part such as by accident, misuse, improper installation, or by affixing any accessories, is not covered by this warranty.
Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing, or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a defect.
Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty hereby disclaims any and all warranties, including but not limited to those of merchant ability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.

Pre Installation

BANSA ROSE 3 Blade Ceiling Fan Light LED Integrated -
fig

Pre-Installation(continued)
HARDWARE INCLUDED
components table

NOTE: Hardware not shown to actual size.

AA Mounting screws 4
88 Expansion Bolts 2
CC Balanced parts package 1
DD Blade attachment screw and fiber washer 6
EE Plastic wire nut(not to scale) 5

PACKAGE CONTENTS

BANSA ROSE 3 Blade Ceiling Fan Light LED Integrated - fig
2

Installation of the hanging bracket(suspension part)

‘Before you begin installing the fan, Switch  power off at Service panel and tock  service disconnecting means to prevent  power from being switched on accidentally. When the service  disconnecting means cannot be locked.
securely fasten a warning device, such   as a tag, to the service panel. 1 poser esresser errr eser errs eteres
Before installing this fan make sure the   outlet box is property installed to the  house structure. To reduce the risk of  re, electric shock, or personal injury,
Mount to outlet box or supporting system  acceptable for fan support. :
(Mounting must support at least 35 Ibs.)
leew wenn nen e nee e enn eeeeene!

For concrete ceiling, use the percussion bit with diameter 8mm to drill holes according to the length  of expansion screws. Then use the attachedexpansion screws to fix the hanging bracket onto the ceiling (selection is made according to actual requirements of the customers).
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.
1 \use the Mounting Bracket & ) a8 a guide, Mark (h@pots where Ibe 4 Expansion Botts (B) will be anit ec.
2)Remave the Mounhng Bracket }. drill 4 holemnd insert 4 Expansion Bolts (2) into the concrete Ceiling, install the mounting brackel and secure with Flat
Washers (C), Spring Washers (D) and Nuts (E).
IMPORTANT : SCREWS & NUTS MUST BE Fa TIGHTENED TILL SNUG
For wooden ceiling, use wood screw to drill on the wooden beam or the “junction box” to fix the hanging bracket (selection is made according to actual requirements of the customers).
ISTEP 1A-WWOODEN CEILING
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.

  1. Use the Mounting Bracket (A) as a guide. mark the spots where the 4 Setf Tapping Screws (8) will be drilled,
  2. Remove the Mounting Bracket (A), drill 4 hates for 3MM diameter, install the mounting bracket onto wooden ceiling with the 4 Self Tapping Screws (B) & Washers (C).
    IMPORTANT : SCREWS MUST BE TIGHTENED TILL SNUG

Assembly — Hanging the Fan(continued)
Preparing for mounting

Loosen 2 screws across from each other and remove the other 2 preassembled screws from mounting plate
(Corresponding to installation step 6). Save screws for later use.
Install blades
place the blade cushions to the blades, lock the assembled blades to the motor by screws one by one
Attention: never lock screws to the motor without putting blades, otherwise the screws will do harm to the motor wires inside. BANSA ROSE 3 Blade
Ceiling Fan Light LED Integrated - fig 10Assembly – Hanging the Fan(continued)
**Preparing for mounting![BANSA ROSE 3 Blade Ceiling Fan Light LED Integrated

  • fig 12](https://manuals.plus/wp-content/uploads/2023/07/BANSA-ROSE-3-Blade- Ceiling-Fan-Light-LED-Integrated-fig-12.jpg)**
    Make wiring connections using wire connectors provided as indicated above. White from house to White from remote receiver marked AC N. Black from house to Black from remote marked AC L. Connect all green grounded wires to Grounded wire from House. Make sure that no laments are outside of the wire connector.

Assembly – Attaching the Lights

take out the screws from the light base,connect the power wires and then lock the light panel to it.BANSA ROSE 3 Blade Ceiling Fan Light LED Integrated -
fig 14

install lampshade
Place the lampshade to the bottom groove and rotating it by clockwise direction until perfect contact (see figures 11,12).BANSA ROSE 3 Blade
Ceiling Fan Light LED Integrated - fig 15
Install canopy and downrod
Put power line through the downrod and decorative cover then connect the downrod to the mainbody.inserting the security bolt and fixed by R lock, finally tighten the screwsBANSA ROSE 3 Blade Ceiling Fan Light LED
Integrated - fig 18
Install canopy and canopy
hang the assembled ceiling fan to the mounting bracketrotate the downrod to ensure the groove on the head of the downrod to match the salient point on the mounting bracket,then lock the canopy to the bracketBANSA ROSE 3 Blade
Ceiling Fan Light LED Integrated - fig 18 Put the receiver in the mounting bracket connect the power lineBANSA ROSE 3 Blade Ceiling Fan Light LED Integrated - fig
19BANSA ROSE 3 Blade Ceiling Fan
Light LED Integrated - fig 20

Use of remote control

Remote Operating Manual

  1. LED Indicator Light
  2. Fan ON/OFF 0 Light on /change color(one press one color change)
  3. Light off
  4. Natural wind
  5. Fan speed control button
  6. Fan Forward and Reverse Rotations Control
  7. Timing
  8. Remote control battery
  9. Use two AAA 1.5 VI

Remote control wiring diagram

BANSA ROSE 3 Blade Ceiling Fan Light LED Integrated -
fig25

Operation

OPERATING YOUR FAN

Turn on the fan and check the condition of the fan operation. And make sure that you can control the fan speed and light properly by the remote control . The appropriate speed settings for warm or cool weather depends on factors such as the room size, ceding height and number of fans.
The slide switch controls the direction of the blades: forward (switch down) or reverse (switch up).
NOTE: Before reversing the direction al the blade rotstim, please wall oft, the (en slops.
A. Warm Weather- Forward Fan rotates anti-cbckwise creating a downward airflow delivering a cooling effect.
Suitable for hot weather condition or air-conditioned condition. A. writer Weather- Reverse
Fan rotates dockwise creating an upward airflow moving warm air off the ceiling areas. This function works best at lower (an speed.
Suitable for cold weather or alr-corxlitioned condition.

Fans Balance

  1. switch on the ceiling fan,if shake is found, switch it off and stick one of the balance pad to the middle of one blades.switch on the fan again to see if there is any improvement.
  2. If there is no improvement,take off the balance pad and stick it to other blades and repeat the testing until fan works well.

WARNING: Makeenthe poNeria off beloadeenIng your fan.

  • Because of the fan’s natural movement, some connections may become loose.
  • Check the support connections. brackets, and blade attachments twice a year. Make sure they are secure, It is not necessary to remove the fan from the ceiling. o Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor. or the wood, or possibly cause an electrical shock. Use only a soft brush or tint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
  •  You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
  • You do not need to oil your fan. The motor has perrnanently4ubticated sealed ball bearings.

Troubleshooting

Problem Solution
The fan will not start. 0  Chock the rnain and francncicuil fuses or

breakers.
0 Check the lino wee connectizos to theta, and switch wire connections in the switch housing.
The fan is noisy.| 0 Ensure Montt housing scams ere snug.
0 Ensure he soots Insl Sento tan blade tradol lo the rota hub are fignt.
0 Ensurelhewirennotnnetionsarencaratting againsteechotherortheintenc’ r wangling switchhcusing. 0 Alowa24-hourbreakinpirtzedod. Most noisesassociatedottioneafandeopzearcbrnpeastene.
0 if you see using the Gang Fan IgN Wtensure the saeuesecuengthegasswareareagtz.Chack theta* WI 0 tutisareabosecue.
0 Ensurelho canopy isa shondstarcefrornlhecolnelt shouldnot kuchtheceling.
0 Ensure yOS0.111e7 tOxIS Neuf° and ,Ober 8013tOr pads wereuSed betMel 1110 MOON) riele and Collet box.
The fan wobbles.| 0 Please chock and follow the instructions:awake No.13 Fan balance on Pogo 12.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

BANSA ROSE User Manuals

Related Manuals