greenworks G24X2LM41 Cordless Lawn Mower Instruction Manual

greenworks G24X2LM41 Cordless Lawn Mower

Product Information

Specifications

• Model: G24X2LM41
• Category: Lawn Mower
• Manufacturer: GLOBGRO AB
• Authorized Representative: Garden Equipment Ltd
• Dimensions: 210mm (length), 145mm (width)
• Weight: 120g (4P60g:1), 164g (4P)
• Standard Compliance: BS EN 60335-1, BS EN 60335-2-77, BS EN 62233, BS EN 55014-1, BS EN 55014-2, BS EN ISO 3744, ISO 11094, BS EN 62321-3-1, BS EN 62321-4, BS EN 62321-5, BS EN 62321-6, BS EN 62321-7-1, BS EN 62321-7-2, BS EN 62321-8
• Noise Emission Level : Measured sound power level – 94.1 dB(A), Guaranteed sound power level – 96 dB(A)

Description

• This machine is a domestic lawn mower designed for cutting grass. It features a cutting blade that should be parallel to the ground and all four wheels must touch the ground during operation.

Overview

1. Bail switch
2. Start button
3. Upper handle
4. Lower handle
5. Rear discharge flap
6. Battery compartment flap
7. Grass catcher
8. Mulch plug

Safety
Ensure to follow these safety guidelines while using the lawn mower:

• Read and understand the operator manual before use.
• Wear appropriate protective gear, such as safety goggles and sturdy shoes.
• Keep bystanders, especially children and pets, at a safe distance.
• Do not operate the mower on slopes greater than the specified limit.
• Do not touch the cutting blade or any moving parts while the machine is in operation.

Installation

1. Remove all packaging materials and check for any damage to the machine.
2. Attach the upper handle to the lower handle using the provided screws and tighten securely.
3. Insert the battery into the battery compartment and close the flap.
4. Attach the grass catcher to the rear discharge flap or insert the mulch plug if desired.

Operation

1. Ensure the cutting blade is parallel to the ground and all four wheels are in contact with the ground.
2. Press and hold the bail switch while simultaneously pressing the start button to start the machine.
3. To stop the machine, release the bail switch.
4. To empty the grass catcher, remove it from the rear discharge flap and dispose of the grass clippings appropriately.
5. When operating on slopes, exercise caution and avoid steep inclines.
6. For optimal operation, follow these tips:
   • Mow in straight lines, overlapping each pass slightly.
   • Adjust the cutting height according to your preference and grass conditions.

Maintenance

1. Perform general maintenance regularly, including cleaning the machine and inspecting for any damage or wear.
2. If the blade becomes dull or damaged, replace it with a new one following the manufacturer’s instructions.
3. Store the machine in a dry and secure location when not in use.

Troubleshooting

• If you encounter any issues with the lawn mower, refer to the troubleshooting section in the operator manual or contact customer support for assistance.

Technical Data

• Weight: 120g (4P60g:1), 164g (4P)
• Noise Emission Level: Measured sound power level – 94.1 dB(A), Guaranteed sound power level – 96 dB(A)

Warranty
The lawn mower is covered by a warranty. Please refer to the warranty documentation for more information.

EC Declaration of Conformity
The lawn mower complies with relevant standards and regulations. The declaration of conformity can be found in the operator manual.

FAQ

1. How often should I perform general maintenance on the lawn mower?
   We recommend performing general maintenance regularly, at least once every season or as needed.

2. Can I use the lawn mower on steep slopes?
   No, it is not recommended to operate the lawn mower on slopes greater than the specified limit for safety reasons.

3. What should I do if the blade becomes dull?
   If the blade becomes dull, it should be replaced with a new one following the manufacturer’s instructions.

4. Where should I store the lawn mower when not in use?
   The lawn mower should be stored in a dry and secure location to protect it from the elements and unauthorized access.

OPERATOR MANUAL

Original Instructions

DECLARATION OF CONFORMITY (UK)

• Name and address of the manufacturer:
  • Name: GLOBGRO AB
• Globe Group Europe
  • Address: Riggaregatan 53, 211 13 Malmö Sweden
• Name and address of the Authorized representative:
  • Name: Garden Equipment Ltd
  • Address: 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK
• Name and address of the person authorised to compile the technical file: Name: Simon Del-Nevo
  • Address: 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK
• Here with we declare that the product
  • Category: Lawn Mower
  • Model: 2512607 (LME367)
  • Serial number: See product rating label

Year of Construction: See product rating label

• is in conformity with the relevant provisions of the Supply of Machinery (Safety) Regulations 2008.
• is in conformity with the provisions of the following other UK legislation
• Electromagnetic Compatibility Regulations 2016
• Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001
• The Restriction of the Use of Certain Hazardous
• substances in Electrical and Electronic Equipment Regulations 2012

Furthermore, we declare that the following standard have been used

• BS EN 60335-1, BS EN 60335-2-77, BS EN 62233, BS EN 55014-1, BS EN 55014-2,
• BS EN ISO 3744, ISO 11094, BS EN 62321-3-1, BS EN 62321-4, BS EN 62321-5,
• BS EN 62321-6, BS EN 62321-7-1, BS EN 62321-7-2, BS EN 62321-8
• Conformity assessment method to Annex E Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001.
• Measured sound power level 94.1 dB(A)
• Guaranteed sound power level 96 dB(A)
• Place, date : Christchurch, Dorset, UK 07.06.2021
• Signature: Ted Qu, Quality Director

DESCRIPTION

PURPOSE
This machine is used for domestic lawn mowing. The cutting blade must be approximately parallel to the ground. All four wheels must touch the ground while you mow.

OVERVIEW

Figure 1~9

1. Bail switch
2. Start button
3. Upper handle
4. Lower handle
5. Rear discharge
6. flap Battery compartment
7. flap Grass catcher
8. Mulch plug
9. Quick-release
10. lever Cam lock
11. Knob
12. Hook
13. Slot
14. Battery pack
15. Safety key
16. Battery release button
17. Height adjustment button
18. Nut
19. Spacer
20. Blade

SAFETY

• WARNING
  Make sure that you follow all safety instructions.
  Refer to Safety Manual.

INSTALLATION

• WARNING
  Do not use accessories that are not recommended by the manufacturer.

• WARNING
  Do not put in the safety key or the battery pack until you finalized the assembly of all the parts.

UNPACK THE MACHINE

WARNING
Make sure that you correctly assemble the machine before use.

WARNING

• If parts of the machine are damaged, do not use the machine.
• If you do not have all the parts, do not operate the machine.
• If the parts are damaged or missing, contact the service center.

1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with local regulations.

UNFOLD AND ADJUST THE LOWER HANDLE
Figure 2.

1. Pull up and back the upper handle to lift the handle into operation position. Make sure that the handles click into position correctly.
2. Tighten the lower handle with the quick-release levers on the two sides.

• NOTE
  Make sure that the two handles are in the same position.

• WARNING
  Do not make damage to the cables when you fold or unfold the handle.

INSTALL THE UPPER HANDLE
Figure 3

1. Align the holes in the upper handle and the lower handle.
2. Put the cam locks through the holes.
3. Tighten the knobs onto the cam locks.
4. Do the same operation on the other side.

INSTALL THE GRASS CATCHER
Figure 4

1. Remove the mulch plug.
2. Open the rear discharge flap and hold it.
3. Hold the the grass catcher by its handle and put the hooks over the slots.
4. Close the rear discharge flap.

INSTALL THE MULCH PLUG
Figure 5.

1. Remove the grass catcher.
2. Open the rear discharge flap and hold it.
3. Hold the mulch plug by its handle and fit it in the discharge chute.
4. Close the rear discharge flap.

SET THE BLADE/CUTTING HEIGHT
The machine can be set to different blade/cutting heights. Figure 6.

1. Push the height adjustment button, move the height adjust gear to a higher position to increase the blade/cutting height.
2. Push the height adjustment button, move the height adjust gear to a lower position to decrease the blade/cutting height.\

INSTALL THE BATTERY PACK
Figure 7

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the engine stops before you install or remove the battery pack.
• Read, know, and follow the instructions in the battery and charger manual.

WARNING
USE ONLY 24V BATTERY. DO NOT USE DUAL-VOLTAGE 24/48V BATTERY.

NOTE
Both batteries should be installed into the compartments in order to start the machine.

1. Open the battery flap.
2. Align the lift ribs on the battery pack with the grooves in the battery compartment.
3. Push the battery pack into the battery compartment until the battery pack locks into place.
4. When you hear a click, the battery pack is installed.
5. Do the same operation with the other battery.
6. Close the battery flap.

NOTE
The motor starts only when you put in the safety key.

REMOVE THE BATTERY PACK

Figure 7

1. Open the battery compartment flap
2. Remove the safety key.
3. Push and hold the battery release button.
4. Remove the battery pack from the machine.

OPERATION

WARNING
Wear eye protection during operation.

START THE MACHINE
Figure 8

1. Put in the safety key and battery.
2. Push and hold the start button.
3. While you hold the start button, pull the bail switch in the direction of the handle bar.
4. Release the start button to start the machine.

STOP THE MACHINE
Figure 8

1. Release the bail switch to stop the machine.

WARNING

• Wait until the blades fully stop before you start the machine again. Do not quickly turn the machine off and on.

WARNING

• Always remove the safety key and battery pack after you complete the work.

EMPTY THE GRASS CATCHER

1. Stop the machine.
2. Remove the safety key.
3. Remove the battery pack.
4. Open the rear discharge flap and hold it.
5. Hold the grass catcher by its handle and unhook it from the slots.
6. Close the rear discharge flap.
7. Empty the grass catcher.

OPERATE ON SLOPES

WARNING
Do not mow on slopes with incline more than 15°. If you are not comfortable, do not mow on a slope.

• Do not go up and down on a slope, mow across the face of the slope. Be careful when you change the direction on a slope.
• Monitor holes, ruts, rocks, and other hidden objects that can cause you to fall. Remove all obstacles such as rocks and tree limbs.
• Make sure that your footing is stable. If you are out of balance, release the handle switch immediately.
• Do not mow near drop-offs, ditches, or embankments.

OPERATION TIPS

• Do not try to override the operation of the start button or bail switch.•
• Do not tilt the machine when you start it.
• Do not put hands or feet near or below the turning parts.
• Keep the discharge chute clean.
• Do not cut wet grass.
• Higher blade height is necessary for new or thick grass.
• Clean the bottom of the mower deck after each use. Remove grass clippings, leaves, dirt, and other debris.

MAINTENANCE

• WARNING
  Remove the safety key and battery pack(s) from the machine before maintenance.

• WARNING
  Keep the motor and battery pack(s) free from grass, leaves or too much grease.\

• CAUTION
  Use only approved replacement parts.

• CAUTION
  Do not let brake fluids, gasoline, petroleum-based materials touch the plastic parts. Chemicals can cause damage to the plastic, and make the plastic unserviceable.

• CAUTION
  Do not use strong solvents or detergents on the plastic housing or components.

• NOTE
  Recommended tightening torque (blade): 33-37 Nm.

GENERAL MAINTENANCE

• Before each use, examine the machine for damaged, missing, or loose parts such as screws, nuts, bolts and caps.
• Tighten correctly all the fasteners and caps.
• Clean the machine with a dry cloth. Do not use water.

REPLACE THE BLADE
Figure 9.

• WARNING
  Use only approved replacement blades.

• WARNING
  Wear heavy gloves or wind cloth around the blade when you touch the blade.

1. Stop the machine.
2. Make sure that the blade fully stops.
3. Remove the safety key and battery pack.
4. Turn the machine to its side.
5. Use a piece of wood to prevent the movement of the blade.
6. Remove the mounting nut and spacer with a wrench or socket.
7. Remove the blade.
8.  Install the new blade. Make sure that the raised points engage the hole(s) in the blade.
9. Put in the mounting nut and spacer and tighten them.

STORE THE MACHINE

• Remove the safety key.
• Remove the battery pack(s).
• Clean the machine before storage.
• Make sure the motor is not hot when you store the machine.
• Make sure that the machine does not have loose or damaged parts. If it is necessary, follow these instructions
  • Replace the damaged parts.
  • Tighten the bolts.
  • Speak to a person at an approved service center.
  •  Store the machine in a dry area.
• Make sure that children cannot come near the machine.

TROUBLESHOOTING

pack.
The bail switch is defective.| Replace the bail switch.
The safety key is not put in.| Put in the safety key.
The machine cuts grass unevenly.| The lawn is rough.| Examine the mow- ing area.
The blade height is not set correctly.| Adjust the blade/ cutting height to a higher position.
The machine does not mulch correctly.| Wet grass clip- pings attach to the deck.| Wait until the grass dries before mowing.
The mulch plug is missing.| Install the mulch plug.
The machine is hard to push.| The grass is too tall, or the blade height is too low.| Increase the blade/ cutting height.
The grass catcher and the blade drags in thick grass.| Empty the grass clippings from the grass catcher.
There is a high vibration in the ma- chine.| The blade is un- balanced and worn.| Replace the blade.
| The motor shaft is bent.| 1. Stop the mo- tor.
| | 2. Remove the safety key and battery pack.
| | 3. Inspect for damage.
| | 4. Repair the ma- chine before you start it again.
The machine stops during mowing.| The blade height is too low.| Increase the blade/ cutting height.
The battery pack is out of power.| Charge the battery pack.
The grass clip- pings attach to the deck or the blade.| Remove the battery pack and check the deck.
Operation temperature of the ma- chine is too high.| Cool the machine.

If you cannot find the solution to these problems, go to the  service center

TECHNICAL DATA

• G24X2C/ G24X2UC2/
• G24X2UC4 and other CAG series

Double-insulated construction|

IPX| IPX4

WARRANTY

(The full warranty terms and conditions can be found on Greenworks website https://www.greenworkstools.eu) The Greenworks warranty is 3 years on the product, and 2 years on batteries (consumer/private usage) from the date of purchase. This warranty covers manufacturing faults. A faulty product under warranty might be either repaired or replaced. A unit that has been misused or used in other ways then described in the owner’s manual might be rejected for warranty. Normal wear, and wear parts are not considered as warranty. The original manufacturer warranty is not affected by any additional warranty offered by a dealer or retailer. A faulty product must be returned to the point of purchase in order to claim for warranty, together with the proof of purchase (receipt)

EC DECLARATION OF CONFORMITY

Name and address of the manufacturer

• Name
  • GLOBGRO AB
  • Globe Group Europe
• Address Riggaregatan 53, 211 13 Malmö, Sweden

Name and address of the person authorized to compile the technical file

• Name:   Micael Johansson
• Address: Riggaregatan 53, 211 13 Malmö, Sweden

Herewith we declare that the product

• Category: Lawn Mower
• Model: 2512607 (LME367)
• Serial number: See product rating label
• Year of Construction: See product rating label is in conformity with the relevant provisions of the
• Machinery Directive 2006/42/EC.
• is in conformity with the provisions of the following other EC-Directives
  • 2014/30/EU
  • 2000/14/EC & 2005/88/EC
  • 2011/65/EU & (EU)2015/863

Furthermore, we declare that the following parts, clauses of harmonized standards have been used

• EN 60335-1, EN 60335-2-77, EN 62233, EN ISO 3744,
• EN 55014-1, EN 55014-2, ISO 11094, IEC 62321-3-1,
• IEC 62321-4, IEC 62321-5, IEC 62321-6, IEC
• 62321-7-1, IEC 62321-7-2, IEC 62321-8

Conformity assessment method to Annex VI Directive 2000/14/EC.

• Measured sound power level LWA: 94.1 dB(A)
• Guaranteed sound power level LWA.d : 96 dB(A)
• Place, date: Mal
• Signature: Ted Qu, Quality Director
• 03.03.2021

References

• Powerful Cordless Gardening Tools | Greenworks Tools
• Greenworks | Battery-powered tools for your home & garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>