greenworks pro STB Series String Trimmer Instruction Manual

GreenWorks pro-STB Series String Trimmer

Product Information

String Trimmer

The String Trimmer is a machine used to cut grass, light weeds, and other similar vegetation at or around ground level. The cutting plane must be approximately parallel to the ground surface. It cannot be used to cut or chop hedges, shrubs, bushes, flowers, and compost. The machine comes with a battery release button, rear handle, lock-out button, trigger, speed switch, upper shaft, auxiliary handle, coupler, lower shaft, motor housing, trimmer head, and guard. The package includes a string trimmer bare tool, auxiliary handle, guard, Allen key, manual, and shoulder strap.

Product Usage Instructions

Important Safety Instructions: Read and understand all instructions before using the String Trimmer. Failure to follow all instructions may result in electric shock, fire, and/or serious personal injury. Keep these instructions for future reference.

Installation

To install the String Trimmer:

• Unpack the machine.
• Attach the guard.
• Assemble the shaft.
• Attach the auxiliary handle.
• Install the battery pack.
• Remove the battery pack when not in use.

Operation

To operate the String Trimmer:

• Ensure that the cutting plane is approximately parallel to the ground surface.

• Hold the rear handle with one hand and the auxiliary handle
  with the other hand.

• Press and hold the lock-out button.

• Squeeze the trigger to start cutting.

• Use the speed switch to adjust the cutting speed.

• Release the trigger to stop cutting.

Maintenance

To maintain the String Trimmer:

• Read the general information in the manual.
• Clean the machine after each use.
• Replace excess lines when necessary.
• Install the cutting line properly.

Transportation and Storage

To move and store the String Trimmer:

• Move the machine carefully and avoid dropping it.
• Store the machine in a dry and secure place.

DESCRIPTION

PURPOSE

This machine is used to cut grass, light weeds, and other similar vegetation at or around ground level. The cutting plane must be approximately parallel to the ground surface. You cannot use the machine to cut or chop hedges, shrubs, bushes, flowers and compost.

OVERVIEW

1. Battery release button
2. Rear handle
3. Lock-out button
4. Trigger
5. Speed switch
6. Upper shaft
7. Auxiliary handle
8. Coupler
9. Lower shaft
10. Motor housing
11. Trimmer head
12. Guard

PACKING LIST

1. String trimmer bare tool
2. Auxiliary handle
3. Guard
4. Allen key
5. Manual
6. Shoulder strap

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING (THIS POWER TOOL)

WARNING: Read and understand all instructions before using this product. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

• Use only identical manufacturer’s replacement parts and accessories. Use of any other parts may create a hazard or cause product damage.

• Always wear safety glasses with side shields marked to comply with ANSI Z87.1. Everyday glasses have only impact resistant lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury. Use face mask if operating in dusty work spaces.

• Avoid Dangerous Environment – Don’t expose power tools to damp or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Don’t use in rain.

• Keep all bystanders, children, and pets at least 50 ft. away.

• Dress Properly – Do not wear loose clothing or jewelry. They can be caught in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.

• Use right Appliance. Do not use appliance for any job except that for which it is intended.

• Avoid Unintentional Starting – Don’t carry appliance with finger on switch. Be sure switch is off when battery is plugged in.

• Don’t Force Appliance – It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

• Don’t overreach – Keep proper footing and balance at all times.

• Stay alert – Watch what you are doing. Use common sense. Do not operate this unit when you are tired, ill or under the influence of alcohol, drugs or medication.

• Always store idle power tools indoors – When not in use, power tools should be stored indoors in a dry and high or locked-up place, out of reach of children.

• Maintain Appliance With Care – Replace string head if cracked, chipped, or damaged in any way. Be sure the string head is properly installed and securely fastened. Keep cutting edge sharp and clean for best performance and to reduce the risk of injury.

• Follow instructions for lubricating and changing accessories. Inspect appliance cord periodically, and if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. Failure to do so can cause serious injury.

• Check damaged parts before using the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, damaged mountings, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual.

• Remove or disconnect battery before servicing, cleaning or removing material from the gardening appliance.

• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care. Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. Use only with Greenworks BAB727/2901302 battery or other BAB series.

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use only with Greenworks GCH8020/GCH8040 charger or other CAB series.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause a fire.
  Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
  Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.

• Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 265 °F (130 °C) may cause an explosion.

• Do not dispose of the batteries in a fire. The cells may explode. Check with local codes for possible special disposal instructions.

• Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

• Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.

• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

• Keep guards in place and in working order.

• Keep hands and feet away from cutting area.

• Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.

• Use only with the nylon cutting line of 0.095″ / 0.080″ (2.4 mm / 2.0 mm) diameter. Do not use heavier lines than recommended by the manufacturer and line materials of other types – for example, metal wire, rope, and the like.

SAVE THESE INSTRUCTIONS

SYMBOLS ON THE MACHINE

Some of the following symbols can be used on this machine. Please study them and learn their definition. Proper interpretation of these symbols will let you operate the tool better and safer.

RISK LEVELS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SERVICE

Servicing requires extreme care and knowledge and must be performed only by a qualified service technician. For service we suggest you return the machine to your nearest AUTHORIZED SERVICE CENTER for repair. Use only identical manufacturer’s replacement parts and accessories.

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

The toxic and corrosive materials below are in the batteries used in this machine: Lithium-Ion, a toxic material.

WARNING

• Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding damaged or worn out Li-ion battery, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for lithium-ion disposal.
• If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery pack. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment:
• Cover the terminals of the battery with heavy-duty adhesive tape.
• DO NOT try to remove or destroy any of the battery pack components.
• DO NOT try to open the battery pack.
• If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in the eyes or on skin, and do not swallow it.
• DO NOT put these batteries in your regular household trash.
• DO NOT incinerate.
• DO NOT put them where they will become part of any waste landfill or municipal solid waste stream.
• Take them to a certified recycling or disposal center.

PROPOSITION 65

WARNING

• This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other masonry products;
• Arsenic and chromium from chemically treated lumber.
• Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

INSTALLATION

UNPACK THE MACHINE

WARNING

• Make sure that you correctly assemble the machine before use.
• If parts of the machine are damaged, do not use the machine.
• If you do not have all the parts, do not operate the machine.
• If parts are damaged or missing, contact the service center.

1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with local regulations.

ATTACH THE GUARD

WARNING

Do not touch the cut-off blade.

1. Remove the screws from the trimmer head with the supplied hex wrench.
2. Put the guard onto the trimmer head.
3. Align the screw holes on the guard with the screw holes on the trimmer head.
4. Tighten the screws.

ASSEMBLE THE SHAFT

1. Loosen the screw on the coupler (2).
2. Push in the release button on the lower shaft (1).
3. Align the release button with the positioning hole and slide the two shafts together.
4. Turn the lower shaft until the button locks into the positioning hole.
5. Tighten the screw with the hex wrench (3).

ATTACH THE AUXILIARY HANDLE

1. Remove the knob (16) from the handle.
2. Attach the auxiliary handle and lower clamp (15) on the shaft.
3. Set the auxiliary handle in the comfortable position.
4. Put the bolt (14) through the holes.
5. Tighten the auxiliary handle with the knob.

INSTALL THE BATTERY PACK

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the motor stops before you install or remove the battery pack.
• Read and understand the instructions in the battery and charger manual.

1. Align the lift ribs on the battery pack with the grooves in the battery compartment.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

REMOVE THE BATTERY PACK

1. Push and hold the battery release button (1).
2. Remove the battery pack from the machine.

WARNING

Be careful when you operate the machine.

CONTROLS

START THE MACHINE

1. Push the lock-out button (3) and pull the trigger (4).
2. 2. Push the speed switch (5) to the desired operating speed. Push the speed switch to position 1 for low speed or position 2 for high speed.

STOP THE MACHINE

1. Release the trigger to stop the machine.

ADJUST THE LENGTH OF THE CUTTING LINE

While you operate the machine, the cutting line gets worn shorter. You can adjust the length of the cutting line.

1. Hit the trimmer head against the ground while you operate the machine.
2. Line is automatically released and the cut-off blade cuts the excess length.

ADJUST THE CUTTING DIAMETER

NOTE

• The machine is set at a 14 in. (35.6 cm) cutting diameter. You can adjust to a 16 in. (40.6 cm) cutting diameter.
• Set the cutting diameter to 14 in. (35.6 cm) for greater runtime and 16 in. (40.6 cm)for a larger cutting area.

1. Remove the battery pack.
2. Remove the blade screws from the cut-off blade (17).
3. Turn the cut-off blade 180°.
4. Tighten the blade screws.

LINE CUT-OFF BLADE

• This trimmer is equipped with a line cut-off blade (17) on the guard. The line cut off blade continuously trims the line to ensure a consistent and efficient cut diameter. Advance line whenever you hear the motor running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep line long enough to advance properly.

OPERATION TIPS

WARNING

Keep clearance between the body and the machine.

WARNING

Do not operate the machine without guard in place.

Do these tips when you use the machine

• Keep a firm hold with the two hands on the machine while the string head is spinning.
• Cut tall grass from the top down.

If grass winds around the trimmer head:

• Remove the battery pack.
• Remove the grass.

CUTTING TIPS

• Tilt the machine toward the area to be cut. Use the tip of the cutting line to cut grass.
• Move the machine from right to left to prevent thrown debris from hitting the operator.
• Do not cut in the danger area.
• Do not force the trimmer head into uncut grass.
• Wire and picket fences cause cutting line wear and breakage. Stone and brick walls, curbs, and wood can wear the cutting line quickly.

MAINTENANCE

IMPORTANT

• Read and understand the safety regulations and the maintenance instructions before you clean, repair or do the maintenance work on the machine.
• Make sure that all nuts, bolts and screws are tight. Examine regularly that you install the handles tightly.
• Use only the replacement parts and accessories of the initial manufacturer.

GENERAL INFORMATION

Only your dealer or approved service center can perform maintenance that is not given in this manual.

Before the maintenance operations:

• Stop the machine.
• Remove the battery pack.
• Cool the motor.
• Store the machine in cool and dry place.
• Use correct clothing, protective gloves and safety glasses.

CLEAN THE MACHINE

• Clean the machine after use with a moist cloth dipped in neutral detergent.
• Do not use aggressive detergents or solvents to clean the plastic parts or handles.
• Keep the trimmer head free of grass, leaves, or excessive grease.
• Keep the air vents clean and free of debris to avoid overheating and damage to the motor or the battery.
• Do not spray water onto the motor and electrical components.

REPLACE EXCESS LINE

1. Push the tabs (18) on the sides of the trimmer head at the same time.
2. Pull and remove the spool cover (19).
3. Remove the remaining spool (21).
4. Clean dirt and debris from all parts. Replace spool if it is worn or damaged.
5. Push the tabs and install the spool cover onto the spool housing.
6. Push the spool cover until it clicks into position.

INSTALL THE CUTTING LINE

NOTE

Do not put more than 15 feet of cutting line in at a time.

1. Remove the remaining cutting line on the spool.
2. Line up the slots on the spool cap with the slots on the trimmer head.
3. Put the cutting line through the hole. Push the cutting line until it exits the opposite hole.
4. Pull the cutting line through until there is an equal quantity of cutting line on each side.
5. Turn the spool cap clock-wise to wind the cutting line into the trimmer head. Keep approximately 5 in of cutting line above out of each side of the trimmer head.

TRANSPORTATION AND STORAGE

WARNING

Remove the battery pack from the machine before transportation and storage.

MOVE THE MACHINE

• When you move the machine, you must:
• Stop the machine.
• Remove the battery pack.

STORE THE MACHINE

• Remove the battery pack from the machine.
• Make sure that children cannot come near the machine.
• Keep the machine away from corrosive agents such as garden chemicals and de-icing salts.
• Secure the machine during transportion to prevent damage or injury. Clean and examine the machine for any damage.

TECHNICAL DATA

2.0 mm)

Cutting path diameter| 14 in. /16 in. (35.6 cm / 40.6 cm)
Feed Type| Bump Feed
Weight (without battery pack)| 7.9 lbs (3.6 kg)
Battery model| BAB727/2901302 and other BAB series
Charger model| GCH8020/GCH8040 and

other CAB series

The recommended ambient temperature range:

TROUBLESHOOTING

2. Check contact and in- stall the battery pack again.

The battery pack is depleted.| Charge the battery pack.
The lock-out but- ton and trigger are not pushed at the same time.| 1.  Pull the lock-out but- ton and hold it.

2.  Pull the trigger to start the machine.

0.080″ (2.4 mm / 2.0

mm) diameter.

 | Grass winds around the motor shaft or the trim- mer head.| 1. Stop the machine.

2. Remove the battery pack.

 |  | 3. Remove the grass from the motor shaft and trim- mer head.
 | The motor is over- loaded.| 1. Remove the trimmer head from the grass.
 |  | 2. The motor will recover to work as soon as the load is removed.
 |  | 3. When you cut, move the trimmer head in and out of the grass to be cut and remove no more than 8″ in length of the grass being cut per pass.
 | The battery pack or machine is too hot.| 1. Cool the battery pack until its function returns to normal. This is best done by bringing the bat- tery into the shade or in- doors.
 |  | 2. Cool the machine for approximately 10 mi- nutes. Remove the bat- tery from the tool to help the tool cool down more quickly.
 | The battery pack is disconnected from the tool.| Install the battery pack again.
 | The battery pack is depleted.| Charge the battery pack.
Problem| Possible Cause| Solution
---|---|---
The line does not ad- vance.| Lines are welded to themselves.| Lubricate with silicone spray.
Not enough line on spool.| Install more line.
Lines are worn too short.| Advance the cutting line by bumping the trimmer head.
Lines are tangled on spool.| 1.  Remove the lines from the spool.

2.  Wind the lines.

The line keeps breaking.| The machine is used incorrectly.| 1.  Cut with the tip of the line, avoid stones, walls and other hard objects.

2.  Advance the cutting line regularly to keep full cutting width.

The grass winds around the trimmer head and motor hous- ing.| Cut tall grass at ground level.| 1.  Cut tall grass from the top down.

2.  Remove no more than 8″ in each pass to prevent wrapping.

The line does not cut well.| The cut-off blade becomes dull.| Sharpen the cut- off blade with a file or replace it.
Vibration increases obviously.| The line is worn down at one side and not advanced in time.| Make sure that the line on both sides is normal. Ad- vance the line.

have been maintained in accordance with the instructions in the owners’ manual supplied with the product from new.
ITEMS NOT COVERED BY WARRANTY:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.

HELPLINE:

• Warranty service is available by calling our toll-free helpline, at 1-855-345-3934.

TRANSPORTATION CHARGES:

• Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Greenworks.
• USA address: Canadian address:
• Greenworks Tools Greenworks Tools Canada Inc.
• P.O. Box 1238 P.O. Box 93095, Newmarket, Ontario
• Mooresville, NC 28115 L3Y 8K3

LIMITED WARRANTY

Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of four (4) years against defects in materials, parts or workmanship. Greenworks, at its own discretion will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units which have been used for personal use that have not been hired or rented for industrial/commercial use, and that

EXPLODED VIEW

No.| Part No.| Qt y| Description| No.| Part No.| Qty| Description
---|---|---|---|---|---|---|---
1| R0201836-00| 1| Auxiliary Handle Assembly| 2| R0202143-00| 1| Trimmer Head Assembly
1.1| R0201826-00| 1| Bolt| 3| R0201830-00| 1| Hex Screw
1.2| R0201827-00| 1| Auxiliary handle| 4| R0201881-00| 1| Guard Assembly
1.3| R0201828-00| 1| Bracket| 5| R0201770-00| 1| Allen key
1.4| R0200792-00| 1| Knob|  |  |  |

www.greenworkstools.com

Documents / Resources

| greenworks pro STB Series String Trimmer [pdf] Instruction Manual
2112302VT, STB80L01, STB80L211, STB Series String Trimmer, STB Series, STB Series Trimmer, String Trimmer, Trimmer
---|---

References

• Greenworks Outdoor Power Equipment, Lawn & Garden Tools

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>