ZEBRONICS ZEB-PixaPlay 12 LED Projector User Manual

: June 5, 2024
: ZEBRONICS

ZEBRONICS ZEB-PixaPlay 12 LED Projector User Manual

Dear Customer,

Thank you for purchasing the ZEB-Pixaplay 12 LED Projector. Please read the user manual carefully before usage & save it for future reference.

Note:

To provide a stable power supply, kindly use the cable provided with the product and connect to a AC100-240V, 50160Hz power source.
Avoid the self-disassembly of the product as it results in the failure of Warranty.
Avoid looking directly at the projector lens while it is active.
Make sure that the projector’s air vents are not blocked while in use. The device must be kept in a well insulated surrounding/or proper functioning.
It is recommended to power OFF the projector after a continuous usage of 6 hours.
Place the projector away from water or other liquids. Avoid water accumulation and ensure good ventilation.
In case of enquiry regarding the projector, email us at [email protected] or contact us at 0444000 0004.

Features:

Home Theatre Projectors for Movies, lV & Gaming etc.
ProjectorcomeswithVGA,AVIN,AUXOUT, USBx2, HDMI
Built in Speaker Wide Compatibility Ceiling Mountable Remote Control

Specification:

Package Contents:

Projector : 1 Unit
Remote Control : 1 Unit
Power Cord : 1 Unit
AV cable : 1 Unit
Support Base : 1 Unit
HDMICable : 1 Unit

Product Description

*NOTE:

To avoid power shortage, please do not mixed use the old and new battery.
To avoid battery leakage corrosion, if do not use remote control for a longtime, please take the battery out.

Setting Up the Projector

Preparation before light on

As following picture, connect the power adaptor.

Power on/Power off

Press button or press remote control to get the projector on.

Boot screen

As the projector start working, after screen display 2 to 5 seconds of boot screen, then come into the multimedia screen.

Focus & Keystone

Keystone
If the projector displays the image that are wider in the top and narrow in the bottom or vice versa, then use the keystone adjuster to
correct the image to have even top and bottom edges.

Image focus

The focus of the projector can be adjusted by the following steps:

Place the projector on a flat surface.
Use the focus adjuster (refer product image) to adjust the focus of the projector until the picture displayed on the screen is in good clarity.

Projector Connection

Multi-Media Connection

Insert the USB into the respective ports. (refer to picture below)

Choose multi-media signal source.

Choose the content which you need display: Movie, Music, Photo, Text.

Choose the file which you wantto display and press ,,ff display or stop.

AV Video Equipment Connect

Use 3 in 1 RCA cable and connect projector to
AV slot (as shown in the image below) choose the signal source video. Support Format: NTSC / PAL

HDMI Equipment Connect

HDMI slot can be connected to computer and all the device with HDMI slot. As connected, elect the source HDMI.

Support files:

576P, 480P, 720P, 1080P, 640×480, 800×600, 1024×768, 1280×1024, 1280×720, 1440×900,
1920×1080, 1366×768, 1280×800, 1440×960, 1600×1200,1680×1050

3.5mm Audio Device Connect

Connect 3.5mm earphone and speaker equipment.

Menu Setting Image Menu
Remote control : Press = key, then the main menu will appear. Press ◄ t ► key, choose to ome into the image sub menu. Press T/J;. key,
choose the program which you want to adjust. Then press “OK” key.

In the image, you could set the following models, such as Picture Mode (Standard, Soft, User,
Dynamic), Color Temperature (Cold, Medium, User), Aspect Ratio (auto, 4:3, 16:9), Noise Reduction (Off, Low, Middle, High, Default).

Press = key, for main menu. Press ◄ t► key, choose audio submenu. Press T/Ji.. key, choose the items which you want to adjust.
Then press “OK” key.

In the audio, you could setthe Balance (-50 to +50), Auto
Volume (Open, Off), Auto Volume (Off, Low, Middle, High, Default), Surround Sound (Off, SRS, Surround).

Press = key on the remote control for main menu, then press ◄ t ► key, choose time submenu, press ‘f/Ji.. key, choose the items
which you want to adjust, then press “OK” key.

You can control the content by the display menu