AplusX X2H eS Wireless Gaming Mouse User Manual
- June 15, 2024
- AplusX
Table of Contents
AplusX X2H eS Wireless Gaming Mouse User Manual
Basic function
Indicator light
Working mode switching
Toggle switch,
- wired mode when moved to the left “X“;
- RF mode when moved to the right “O“;
DPI Setting
Gather Step 1: Press the “DPI” switch to light the OLED, and the OLED
will display the current set values;
Gather Step 2: Press the switch again, set the DPI value, at this time
OLED will only display the DPI value, other Settings will be hidden;
Gather Step 3: After the setting is complete, wait 3 second, OLED will
display the current overall setting values;
Gather Step 4: Wait another 3 second and the OLED will turn off;
DPI sets the step level 400-800-1600-3200-6400-12800 Back and forth cycle
Polling Rate Setting
Gather Step 1: Press the “HZ” switch to light the OLED, and the OLED will
display the current set values;
Gather Step 2: Press the switch again, set the polling rate value, at
this time OLED will only display the polling rate value, other Settings will
be hidden;
Gather Step 3 : After the setting is complete, wait 3 second, OLED will
display the current overall setting values;
Gather Step 4 : Wait another 3 second and the OLED will turn off;
Wire mode polling rate sets the step level 500Hz-1000Hz-2000Hz-4000HZ-8000Hz
Back and forth cycle
Wireless mode polling rate sets the step level 500Hz-1000Hz-2000Hz-4000HZ Back
and forth cycle
LOD Setting
Gather Step 1: Press the “HZ” switch to light the OLED, and the OLED will
display the current set values;
Gather Step 2: Hold down the “HZ” switch and set the LOD height value by
pressing the right mouse button. At this time, OLED will only display the
current LOD set value, and other set values will be hidden;
Gather Step 3: After the setting is complete, wait 3 second, OLED will
display the current overall setting values;
Gather Step 4: Wait another 3 second and the OLED will turn off;
LOD sets the step level 1mm—2mm Back and forth cycle
Motion Sync Setting
Gather Step 1: Press the “HZ” switch to light the OLED, and the OLED will
display the current set values;
Gather Step 2: Hold down the “HZ” switch and press the right mouse button
to enable or disable the “Motion Sync” function. At this point, the OLED will
only display the current set value, and other set values will be hidden;
Gather Step 3: After the setting is complete, wait 3 second, OLED will
display the current overall setting values;
Gather Step 4: Wait another 3 second and the OLED will turn off;
Motion Sync sets the step level ON—OFF Back and forth cycle
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>