REVOPOINT POP3 Handheld Stabilizer User Manual Handheld Stabilizer User Manual

: December 6, 2023
: REVOPOINT

POP3 Handheld Stabilizer

Handheld Stabilizer User Manual

Specifications

Product Name: Handheld Stabilizer
Compatible Scanners: Revopoint 3D scanners
Power Output: –
Dimensions: –
Weight: –
Battery Type: –
Battery Capacity: –
Operating Time: –
Recharging Time: –
Stabilized Axes: –
Controllable Range: –
Connection Type: –
Charging Port Type: Type-C
Working Temperature: –

Introduction

The Revopoint Handheld Stabilizer is specially designed for
smooth handheld scans. Its high-precision gyroscope and
anti-shaking systems significantly reduce low-point cloud accuracy
and tracking loss due to shaking. The motorized axes allow you to
pan or tilt the scanner as you move around the object.

Working Mode

The Handheld Stabilizer supports two working modes:

Intelligent Tracking Mode

In this mode, the Handheld Stabilizer will automatically keep
the 3D scanner focused on the object being scanned as you move
around it.

Pan Locked Mode

The pan motor is locked in place without following the handle’s
movements.

Setting up the Handheld Stabilizer

Follow these steps to set up the Handheld Stabilizer:

Step 1: Clip the Revopoint 3D scanner into the quick-release

slot on the top of the Handheld Stabilizer.

Note: Make sure your scanner has a Quick Setup Board. Check and
use a screwdriver to tighten it if it’s loose.

Step 2: Connect and secure the Type C cable to the

scanner.

Note: If your scanner has a Type-C power port, use the Type-C
Adapter to connect it.

Step 3: Long press the Power Button to turn on the Handheld

Stabilizer and power the 3D scanner on.

When the scanner’s LED turns solid green, it’s ready to
connect.

Connecting to a PC

Follow these steps to connect the Handheld Stabilizer to a
PC:

Each Revopoint 3D scanner has a unique Wi-Fi name. Check your
scanner’s serial number on its back to identify your scanner’s
Wi-Fi connection. The following is an example of how to connect a
RANGE with the serial number: A22B0025-2B6F10A74.
Search for the WLAN: RANGE-REVO-A22B0025 and connect to
it.
Double-click to open Revo Scan on your PC and confirm the
scanner is connected successfully.
Go to the scanning interface –> Accessories Menu –>
Handheld Stabilizer –> Click Connection.
Select the Handheld Stabilizer from the available devices and
click Connect. When it’s connected successfully, the Bluetooth LED
will turn solid blue. (Make sure the PC’s Bluetooth is On.)
Start your scan.

Connecting to a smartphone

Follow these steps to connect the Handheld Stabilizer to a
smartphone:

The following is an example of how to connect a RANGE with the
serial number: A22B0025-2B6F10A74.
Screw the Phone Holder Bracket into the 1/4 Threaded Hole, then
attach the Phone Holder that came with your Revopoint 3D scanner if
you want to connect your phone.

What’s in the Box?

Handheld Stabilizer
Phone Holder Bracket
Charging Cable
Type-C Adapter
Strap

FAQ

Q: How do I switch between Follow mode and Pan Locked

mode?

A: Double press the ON/OFF switch quickly to change between
Follow/Pan Locked mode.

Q: How do I start or pause the scan?

A: Press the Start/Pause Scan Button once to start or pause the
scan.

Q: How do I activate or deactivate Intelligent Tracking

mode?

A: Double press the Start/Pause Scan Button to activate or
deactivate Intelligent Tracking mode.

Handheld Stabilizer
User Manual V2.0

Table of Content
Introduction ………………………………………………………………………………………. 1 Working Mode…………………………………………………………………………………..2 Specifications …………………………………………………………………………………….3 What’s in the Box?…………………………………………………………………………….4 Setting up the Handheld Stabilizer……………………………………………..4 Charging the Handheld Stabilizer ……………………………………………….8

Handheld Stabilizer User Manual
Introduction
The Revopoint Handheld Stabilizer is specially designed for smooth handheld scans. Its high-precision gyroscope and anti-shaking systems significantly reduce low-point cloud accuracy and tracking loss due to shaking. The motorized axes allow you to pan or tilt the scanner as you move around the object.
Battery Indicator Shows the remaining battery level. The LED indicator flashes continuously while charging and turns solid white when fully charged. Bluetooth LED Shows the Handheld Stabilizer’s Bluetooth connection status. Flashing Blue: Powered on, and the Bluetooth is ready for connection. Solid Blue: Bluetooth connected successfully. 1 ©2023 REVOPOINT 3D ALL RIGHTS RESERVED

Handheld Stabilizer User Manual
Joystick Controls the scanner’s movement. Up/Down: Tilt control Left/Right: Pan control
1/4 Threaded Hole Screw in the phone holder bracket, then attach the Phone Holder that came with your Revopoint 3D scanner if you want to connect your phone.
ON/OFF Switch Press and hold to power on/off the Handheld Stabilizer. Press once to recenter the Handheld Stabilizer. Double press quickly to change between Follow/Pan Locked mode.
Start/Pause Scan Button Press once to start or pause the scan. Double press to activate or deactivate Intelligent Tracking mode.
Type-C Port The Handheld Stabilizer’s charging port.
Working Mode
Intelligent Tracking Mode
In this mode, the Handheld Stabilizer will automatically keep the 3D scanner focused on the object being scanned as you move around it.
Pan Locked Mode
The pan motor is locked in place without follow the handle’s movements.
©2023 REVOPOINT 3D ALL RIGHTS RESERVED 2

Handheld Stabilizer User Manual
Specifications

Product Name Compatible Scanners Power Output Dimensions Weight Battery Type Battery Capacity Operating Time Recharging Time Stabilized Axes Controllable Range Connection Type Charging Port Type

Handheld Stabilizer Revopoint 3D Scanners 5V/2A 213mm × 84.5mm × 45mm 510g Lithium 4000mAh Around 6 hours 4 hours 2 Tilt±45°, Pan±85° Via Bluetooth USB Type-C

Working Temperature

Note

*Operating time may vary depending on different scenarios and environments.

What’s in the Box?

Handheld Stabilizer User Manual

Handheld Stabilizer Phone Holder Bracket Charging Cable

Type-C Adapter Strap

Setting up the Handheld Stabilizer

Step 1: Clip a Revopoint 3D scanner into the quick-release slot on the top of the Handheld Stabilizer. Note: Make sure your scanner has a Quick Setup Board. Check and use a screwdriver to tighten it if it’s loose.

Step 2: Connect and secure the Type C cable to the scanner. Note: If your scanner has a Type-C power port, use the Type-C Adapter to connect it.
©2023 REVOPOINT 3D ALL RIGHTS RESERVED 4

Handheld Stabilizer User Manual
Step 3: Long press the Power Button to turn on the Handheld Stabilizer and power the 3D scanner on. When the scanner’s LED turns solid green, it’s ready to connect.
Step 4: Connect the 3D scanner to a PC or a smartphone via Wi-Fi. 5 ©2023 REVOPOINT 3D ALL RIGHTS RESERVED

Handheld Stabilizer User Manual 1) Connecting to a PC. Each Revopoint 3D scanner has a unique Wi-Fi name. Check your scanner’s serial number on its back to identify your scanner’s Wi-Fi connection. The following is an example of how to connect a RANGE with the serial number: A22B0025-2B6F10A74. a. Search for the WLAN: RANGE-REVO-A22B0025 and connect to it. b. Double-click to open Revo Scan on your PC and confirm the scanner is connected successfully.
c. Go to the scanning interface –> Accessories Menu –> Handheld Stabilizer –> Click Connection.
d. Select the Handheld Stabilizer from the available devices and click Connect. When it’s connected successfully, the Bluetooth LED will turn in solid blue. (Make sure the PC’s Bluetooth is On.) e. Start your scan. 2) Connecting to a smartphone. The following is an example of how to connect a RANGE with the serial number: A22B0025-2B6F10A74. a. Screw the Phone Holder Bracket into the 1/4 Threaded Hole, then
©2023 REVOPOINT 3D ALL RIGHTS RESERVED 6

Handheld Stabilizer User Manual attach the Phone Holder that came with your 3D scanner and fix your phone in it. See the image below:
b. Connect the scanner to your phone via Wi-Fi. Select the Network RANGE-REVO- A22B0025 on your phone’s WLAN list, and wait for it to connect.
c. Tap the Revo Scan icon on your phone and confirm the scanner is connected.
d. Connect the Handheld Stabilizer to the Revo Scan. When it’s connected successfully, the Bluetooth LED will turn in solid blue. (Make sure the Bluetooth on your phone is On.)
7 ©2023 REVOPOINT 3D ALL RIGHTS RESERVED

Handheld Stabilizer User Manual
Charging the Handheld Stabilizer
1. Connect the Type-A end of the USB cable to an adapter, then plug it into a power socket. 2. Plug the Type-C end of the USB cable into the Handheld Stabilizer’s Type-C port.
3. The Handheld Stabilizer is fully charged when the battery indicator turns solid white.
©2023 REVOPOINT 3D ALL RIGHTS RESERVED 8

This content is subject to change.
If you have any questions about this document, please feel free to contact us! Tel (US): Toll-free +1 (888) 807-3339 Tel (China): +86 18124196779 Live Chat: https://www.revopoint3d.com Skype: +1 323 892 0859 Email: customer@revopoint3d.com
©2023 REVOPOINT 3D ALL RIGHTS RESERVED