SWEETLF SWS7105 Wet and Dry Electric Shaver User Manual

June 15, 2024
SweetLF

SWEETLF SWS7105 Wet and Dry Electric Shaver

SWEETLF-SWS7105-Wet-and-Dry-Electric-Shaver-PRODUCT

General Information

  1. Protective cover
  2. Shaving unit
  3. Fixing rack
  4. Fixed frame lock
  5. Shaver head release button
  6. Shaver on / off button
  7. Five-level electric digital display
  8. Trimmer
  9. USB charging connect

When charging this product, please keep away from water to prevent personal injury.
This product is designed to be fully washable and is suitable for cleaning under open taps.

Please note during operation:
Please separate the Handle part from the power cord (adapter) before cleaning the Handle part in water.

Product Introduction

Please read this user manual, as it contains information about the wonderful features of this shaver as well as some tips to make shaving easier and more enjoyable.

Attention
Before using this product, please read User manual carefully a nd keep it for future reference.

  • Close supervision is necessary when this shaver is used in the presence of children.
  • To avoid injury, never use the shaver if there is any damage.
  • The temperature range to operate, store and charge this product is 0 ℃ ~ 40℃.
  • This product can be charged by phone charger.
  • The shaver is designed to be IPX7 waterproof and can bewashed directly under the water. It’s not suggested toimmerse the shaver under water for a long time,which will reduce the life time of the shaver.
  • Remember to check if the water is too hot to avoid scalding your hands.
  • When you are on a trip, make sure the protective cover is on to protect the shaver heads. If there is a significant change in temperature, pressure, or humidity, please allow the shaver 30 minutes adaptation to new conditions before use.
  • Use the USB charging cable in the package. Please connect the shaver to an AC outlet with 5V output or less, such as a phone charger or computer USB port.

Charging instruction

When Charging
5 white displays will all light on to display the remaining battery one by one and light down one by one to show the battery. When it was 0-10% of the electricity, the light displays as red. When reaches 10%, the red light turns white with a flash. When filled to 20% capacity, the light will become always bright and stop the flash immediately. At the same time, the second white light becomes flashing. When the fifth LED is filled with full battery, the 5 LED will always light and display a full charge.

When the battery is fully charged
Fully charged needs 1 hour charging time to last approximately 120 minutes shaving time.

When the battery is running low
When the first indicator light turns red blinking, that means you need to recharge the shaver.

Charging Procedure
  1. Connect the USB cable to your adapter and other power supply or directly to your computer.
  2. After the battery is fully charged, unplug it from the wall socket and unplug the cable from the shaver USB plug.

Using

Connect the shaver to an AC outlet with 5V output or less, such as a phone charger or computer USB port.

  • Press the on / off button to open or close the shaver.
  • The shaving heads detour on your skin. Your skin may need 2-3 weeks to adapt to the SweetLF shaving system.(Figure 1)
  • Trimming sideburns: push the slide down key under the sideburns knife to make sideburns knife pop out and trim sideburns beard.
  • After shaving, press the on / off button to turn off the shaver; then put on    protective cover to prevent damage.

Note
When the head is damaged, do not shave, so as not to damage your skin.

Clean instruction

Do not use compressed air, scouring pads, abrasive cleaning agents or petrol, acetone, and other corrosive liquid to clean the shaver.

  • You can rinse the shaver under the tap or clean it with a brush we equip.
  • Be careful when using hot water. Always check the water temperature to make sure is not too high to prevent scald.
  • Clean it each time after shaving to obtain the best shaving performance.
  • A damp cloth is available to clean the outside of the shaver, but do not wipe the shaving blade parts with a towel or tissue, as this may damage the shaving blades.
    • Switch off the shaver. Press the release button, and open the shaving unit.(Figure 2)
    • Pull out the Shave blades part from the shaver.(Figure 3)
    • Turn the locking device (A) counterclockwise, remove the retaining frame (B). (Figure 4)
    • Remove and clean the shaving heads one by one. Each contains a  set of razor head cutters and guards. (Figure 5)

Note
Remove the blade from the guards and use the brush for cleaning. Do not clean more than one cutter and guard because they are matched with each other. If you accidentally mix up thecutters and guards, it may take several weeks to restore the best shaving functions.

  • Clean inside and out with a clean brush grille. (Figure 6)
  • Make sure the shaver head recess portion aligned with the recessed portion. (Figure 8)
  • Put the shaving heads back into the shaving unit.(Figure 7)
  • Put the holder (B) back into the shaving unit, then turn the locking device (A) clockwise.(Figure 9)
  • Put the flange fork shaving unit into the slot at the top of the shave shaving unit. (Figure 10)

Note
If the shaving unit closed sluggishly, check the shaving head to make sure it is inserted correctly and the holder is locked.

Store instructions
With a protective cap on the shaver shaving heads to avoid damage.(Figure 11)

Change blades
For the best shaving performance, we recommend replacing blades regularly. To replace the blades, follow the steps below.

  • Switch off the shaver. Disconnect the shaver. Press the release button to open the shaving unit. Pull out the Shave blades parts from the shaver . (Figure 12)
  • Turn the locking device (A) clockwise to remove the retaining frame (B). Remove the shaving blades and put the new one in the shaving unit . (Figure 13)
  • Ensure alignment of just shaving heads recessed portion recessed portion. (Replace it with adverse way of the above sequence ) (Figure 14)
  • The holder (B) back into the shaving unit, the clockwise rotation of the locking device (A). (Figure 15)
  • Put the flange fork shaving unit into the slot at the top of the shave close the shaving unit. (Figure 16)

Note
If the shaving unit is closed sluggishly, check the shaving head to make sure it is inserted correctly and the holder is locked.

Environmental protection

  1. To throw away the product, please do not stack with normal household waste; it should be handed over to an official collection center.
  2. Remove the rechargeable battery shaver.
  3. To remove the battery only when you discard the shaver and make sure the battery is completely depleted.

Specific steps

  • Turn off the shave
  • Let the shaver run until it stops.
  • Remove the razor stubble storage Indoor screws.
  • Remove the screw shell.
  • Remove the batter

Specifications

Input voltage Output voltage Output current Rated power Run time Charging
time 100-240V 50Hz/60Hz 5V 1000mA 8W 120min 60min

Documents / Resources

| SWEETLF SWS7105 Wet and Dry Electric Shaver [pdf] User Manual
SWS7105 Wet and Dry Electric Shaver, SWS7105, Wet and Dry Electric Shaver, Dry Electric Shaver, Electric Shaver, Shaver
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals