MT-VIKI MT-1716MS Combined High Density LED KVM Switch User Manual

**MT-VIKI MT-1716MS Combined High Density LED KVM Switch User Manual

**

Front View

KVM Front View

Note

1. Built in USB control interface suitable for USB1 1 devices
2. Power button convenient to control power on and off

Introduction

The traditional four-in-one LCD KVM is an inseparable whole, usually weighs about 25KG, which is very heavy and requires two people to work together to complete the installation. A set of wire harnesses are used between the display end of the equipment and the KVM to be pulled by the tank chain, which is very complicated and easy to get stuck. The whole machine must be disassembled for maintenance, and transportation is fragile and expensive.

The combined high density LED KVM switch is a new server control platform for the computer room. It abandons the defects of the traditional KVM. The KVM module and the screen display operating end can be easily separated from the bracket tray. Installation can be done easily by one person. Maintenance and upgrade, as long as the KVM module or screen display is easily removed, it can be completed within 3 seconds. Many parts are made of aluminum, which are foldable and easy to transport.

This series of KVM control platform has the characteristics of improved efficiency, simple use, easy management, cost saving, remote management, environmental protection and energy saving. Its height is standard 1U, conforms to 19 rack structures, and saves more than 85% of the cabinet’s use space. The aluminum shell is easy and simple, and it can be carried in and out at any time. It has good corrosion resistance and heat dissipation function.

Front Top View

Side Top View

Structure Diagram

Diagram 8 16 (/ )

Installation

Before installation, the fixed bracket of the cabinet must be adjusted to the installation position of the standard server.

Step 1 : Open the rear door of the cabinet, choose an appropriate height, and put the KVM module and small tray into the cabinet.

Step 2 : At the front of the cabinet, insert the operating end of the screen display and the large tray into the support arm of the small tray, and then fix the cabinet screws.

Step 3: Connect the KVM module and the operating terminal of the screen display with a DVI cable.
Step 4: Use a dedicated KVM cable to connect the KVM and the server.
Step 5 : Turn on the power and complete the installation.

Feature

• 17 inch monitor/mouse/keyboard/smart switch
• Excellent video effect, the best resolution can reach 1280*1024, the external control terminal supports 1920X1080 60Hz
• Support password protection and search PC server name
• LED LCD screen automatic adjustment function
• Support complete DDC2B function, can detect the screen model without switching the computer
• Support simultaneous use of server input with built-in USB keyboard and mouse
• Drawable installation design, the length can be adjusted to fit the rack space
• No additional software is required, and it can be switched by panel buttons, hot keys, or OSD screen menu
• 98-key keyboard and TouchPAD touch sliding mouse
• Support various server operating systems: Dos/Windows series, Linux, Unix, Mac OS 8.6/9/10, SUN Solaris 8/9
• Using aluminum shell material, easy to install, light and portable design
• Data only needs to be transmitted through standard (full-pin 24+5) DVI cable
• Support automatic scan, the default scan time is 5 seconds
• PC board and KVM connection cable within 0-100 meters, the best effect is 50 meters

Specification

Windows9X./Me/nt/2K/XP
Keyboard Interface| US8
Service Life| More than 1,000,000 times
Mouse       Touchpad      (2buttons)| Hardware Interface| USB
Operating System| support Me/nt/2K/XP
Service Life| More than 1,000,000 times
Power Input| DC12V
Shell Color| Black
Shell Material| Aluminum and Iron
Size (WxDxH)| 480x600x4Smm
Cabinet Installation Depth| 600mm-810m (choose appropriate mounting ears)
Operating Temperature| -45.C.-60t
Stored Temperature| -20t-65 ‘C

Specification Hot-key Command

In addition to the panel buttons, you can also switch ports through a simple keyboard combination. You only need to press the HOME/Caps/Scroll/Num key twice within 2 seconds to send a command to the KVM, and then you will hear a ” “Beep” to confirm that you can use the hot-key commands. This product has multiple modes to choose from. [HOME] + [HOME] is the default mode, you can choose other command modes when you don’t want to use this mode. The following is how to set different hot-key modes.

Default mode
Caps mode
Scroll mode
Num mode

Default Mode Command

to switch to the corresponding port
to switch to the next port
to switch to the previous port
turn off or turn on the buzzer sound
automatic scanning, press any key to stop

scanning and stay on the current port

If you want to use Caps mode, please press [HOME]+ [HOME]+Caps firstly, then enter Caps mode and so on , .

Caps Mode Command

to switch to the corresponding port
to switch to the next port
to switch to the previous port
turn off or turn on the buzzer sound
automatic scanning, press any key to stop

scanning and stay on the current port

OSD Menu Operation

The hot-key function can also be implemented under OSD. To select a hot-key port from the OSD menu, you need to press the following operation: [HOME]+ [HOME]+ [Enter] to activate the OSD menu.

The main menu is shown in F igure 1
    

Depending on the selected user the red characters will be automatically modified
Number of 8 means 8 port KVM
Number of 16 means 16 port KVM

****Indicates the current port Show auto scan on corresponding port Indicates the communication status between the corresponding port TX and the host USB, and green indicates that the corresponding port host and USB communication are normal. The cursor can be moved with the arrow keys on the keyboard or remote control. The port where the cursor is located can be confirmed by pressing the keyboard [enter] or the remote control [OK].

Menu setting
F1, F2, F3, F4, F6, ESC should be operated on the keyboard.
★ F1: Modify name When changing the name, the remote control can only input 0-9 numbers. If you need to enter letters, you must use the keyboard to enter them.

★ F2: Set the port to be scanned Set AutoScan Mode with F3, press F2 in the TAG option to turn on or off the scan, and the mark “T” is shown in Figure 2:

★F3: Enter the system settings as shown in Figure 3

Setting method Under the current option press ENTER to set

1. Buzzer Turn on or off the buzzer sound

   • On: turn on the buzzer sound
   • Off: Turn off the buzzer sound

2. Brightness Adust adjust brightness

3.  Contrast Adust adjust contrast

4. AutoScan Mode Auto Scan Mode

   • FREE :Scan all ports
   • CONN: option means only scan the PC connected to USB
   • TAG: Only scan ports with T logo and use it with F2

5. AutoScan Interval Scan the dwell time of each port the default is 5 seconds

6. Banner Interval When switching ports it displays the time the window stays

7. Adj OSD Position Adjust the position of the OSD window press Enter and then press the up down left and right keys on the keyboard to adjust
   To exit please press ESC on the keyboard

   • BAR: Adjust the display position of the port prompt banner
   • MAIN: Adjust the display position of the OSD menu BRI Adjust the display position of contrast and brightness

8. Plugin Mode Select hot plug automatic switching function NO There is no automatic switching function for hot swap

   • ALL It means that every time a USB device is inserted a device with a 5V input in the USB port it will automatically switch to the port just inserted with priority
   • ONCE: There is only one automatic switching action when hot plugging

9. Factory Default Restore factory settings the functions that have been set are restored to factory defaults

★ F7 Security: To set to open or close user management To enter this feature you need to press F3 and then F7 The finger character indicates the current status As shown in Figure 4

Yes: Open the management user settings At this time power off or reset requires a password to enter
No : Close the management user settings no password is required to enter

F1 to modify the user name (user name: ADMIN, USER01, USER02, USER3…The six X behind are hidden passwords, you need to press F5 to view) as shown in Figure 5:

F5 to view the current password. As shown in the figure above, move the cursor on ADMIN, press F5 to display the default password of the first user is 000000.

F4 can modify the password
When set to yes KVM power off or reset will prompt to login as shown in Figure 6 ”

★F6: Set the host assigned to non-administrators, as shown in Figure 7

After activating the OSD menu, press the keyboard F6 to enter the Figure 7, press the keyboard F1 F2 F3 F4 F5 in the green part, and the numbers 12345 will appear on the OSD menu. These numbers represent USER01-05 users. Press F8 to assign all users, and DEL to delete all users’ permissions. For example: 01.SYSTEM01~05.SYSTEM05 These 5 hosts have assigned permissions, enter the user name and the corresponding user password when logging in. Enter user name: USER01, password: 111111. At this time, only the first and fifth computers can be controlled. The default administrator user name: ADMIN password: 000000, when you enter this account, you can control any host.

Packing List

x DC12V power
1x manual
2x hanging ear
PC mode option ( )

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>