eira ER2630VW HDMI 2X2 Video Wall Controller Instructions

: June 15, 2024
: eira

Table of Contents

eira ER2630VW HDMI 2X2 Video Wall Controller
Product Information
Product Usage Instructions
Introduction
Features
Specifications
Connection
Package Contents
Panel Description
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

eira ER2630VW HDMI 2X2 Video Wall Controller

$eira-ER2630VW-HDMI-2X2-Video-Wall-Controller-FIG- $2$$

Product Information

Specifications

Brand: EIRA
SKU Product Name: ER2630VW HDMI 2X2 VIDEO WALL CONTROLLER (1080P@60HZ)
HDMI Input: 1x HDMI
HDMI Output: 4x HDMI
Compatibility Video signal: HDMI 1.4 HDCP 1.4
Resolutions: 1080p@50/60Hz, 720p@50/60Hz, 576p@50Hz, 480p@60Hz, 1920×1200, 1280×960, 1280×800, 1280×768, 1680×1050, 1360×768, 1366×768, 1600×900, 1024×768, 800×600
3.5mm Output Audio signal: PCM
HDMI Output Mode: 1×1/1×2/1×3/1×4/2×2/2×1/3×1/4×1
DIP Switch Splice Settings: RS-232 GND/RxD/TxD
Default Baud Rate: 9600
Power Supply: DC5V/1A
Power Consumption: 4W
Working temperature: -20~60°C
Storage temperature: -30~70°C
Humidity: 0~90%RH (No condensation)
Housing: Iron
Weight: 280 gm
Colour: Black
Dimensions: 151.5(L)86.5(W)20.0(H)mm
ESD protection: Implementation of the standard IEC61000-4-2
Lightning protection, Surge protection

Product Usage Instructions

Installation

To install the HDMI 2X2 Video Wall Controller, follow these steps:

Ensure that the power supply is disconnected.
Connect one end of the HDMI cable to the HDMI input port of the controller.
Connect the other end of the HDMI cable to the HDMI output port of your video source.
Connect the HDMI output ports of the controller to the HDMI input ports of your display devices.
Connect the 3.5mm audio output port of the controller to your audio system, if required.
Connect the power supply to the controller and plug it into a power outlet.

Splicing Modes

The HDMI 2X2 Video Wall Controller supports various splicing modes. These modes can be set using either RS-232 or the DIP switch on the controller. Follow the instructions below to set the desired splicing mode:

Using RS-232:

Ensure that the DIP switch is set to 111.
Connect an RS-232 cable to the RS-232 port of the controller.
Connect the other end of the RS-232 cable to your computer or control system.
Using the appropriate software or commands, send the mode-switching command to the controller.

Using DIP Switch:

Refer to the DIP switch settings in the manual to determine the binary representation of the desired splicing mode.
Set the DIP switch accordingly.

Power On and Off

To power on the HDMI 2X2 Video Wall Controller, simply connect the power supply to a power outlet. To power off the controller, disconnect the power supply from the power outlet.

Troubleshooting

If you encounter any issues with the HDMI 2X2 Video Wall Controller, refer to the troubleshooting section in the user manual for possible solutions.

FAQ

Q: What is the maximum resolution supported by the HDMI 2X2 Video Wall Controller?
A: The controller supports resolutions up to 1080p@60Hz.
Q: Can I use this controller for home theater setups?
A: Yes, the HDMI 2X2 Video Wall Controller can be used in home theater setups.
Q: Does the controller support audio output?
A: Yes, the controller has a 3.5mm audio output for connecting to an audio system.
Q: Can I switch between different splicing modes on the fly?
A: Yes, when the DIP switch is set to 111, you can switch between modes using RS-232 commands.

Introduction

This product is a 1-in-4-out video wall controller, supports one HDMI source input and four HDMI outputs. Supports 1×1/1×2/1×3/1×4/2×2/2×1/3×1/4×1 splicing modes, which can be set by RS-232 or dip switch control, allowing you to tailor the display of the video wall to your requirements. The product can flexibly adapt to different installation requirements, which can be widely used in security monitoring, rail transit, broadcasting, smart cities, home theatre, training and other fields.

Features

Supports 1 HDMI signal input and 4 HDMI signal output.
Support up to 1920×1200@60Hz resolution, downwards compatible.
Support a variety of splicing modes, such as 1×1/1×2/1×3/1×4/2×2, etc.
Support dip switch switching splicing mode.
Support RS-232 control instruction to set splicing mode.
Support 3.5mm left/right channel audio output.
Supports 180-degree rotation of HDMI1/2 display image in 2×2 mode (when upper displays installed upside down).
Firmware upgrading via micro USB port.
Lightning protection, surge protection, ESD protection.
Plug and play, no need to install drivers. Users can quickly set up their video wall without any hassle.