HOLLYLAND C1 Wired Headset User Guide
- June 15, 2024
- HOLLYLAND
Table of Contents
**HOLLYLAND C1 Wired Headset User Guide
**
PACKING LIST
-
Headset 1
-
Over-ear Leather Cushion 1
-
Microphone Cushion 1
-
Storage Bag 1
-
Quick Guide 1
-
Warranty Card 1
Note: The amount of items depends on the configuration of product.
PRODUCT INTERFACES
- Microphone
- Headset Jack
- Adjustable Headband
- Speaker
- Microphone Boom
3.5 mm Headset Jack Jack Definition: M G R L
PRODUCT INSTALLATION AND USAGE GUIDE
Install Solid com C1 headset:
- Plug the headset into the 3.5 mm port of the HUB Base and rotate the nut clockwise to secure the headset.
- Move the microphone boom down, and you can hear a ‘click’. Then you can start to talk.
- If you just want to listen, make the microphone boom upgright. Then, you will hear a ‘click’sound. And microphone will mute at the time.
SPECIFICATIONS
| Type | Monaural |
|---|---|
| Cable Length | Approximately 61” (1550mm) |
| Frequency Information | Speaker: 100Hz~10KHz Microphone: 100Hz~10KHz |
| Distortion | ~10KHz Distortion < |
| Microphone Sensitivity | < 1% |
| Microphone Type | -38±4 dBV @1KHz, 94dBSPL |
| Impedance | Electret (Single-Pointing) |
| Weight | Approximately 6 oz. (170g) |
| Working Temperature | 0~+45°C(working status) -10~+60°C(working status) |
Safety Precautions
Do not place the product near or inside heating devices including but not limited-ta microwave ovens, induction comakers, electric ovens, electric heaters, pressurizers, water heaters, gas stoves) to prevent the battery from overheating and exploding. Never use non-original charging cases, cables and batteries with the product.The use of non-original spare parts may cause electric shock, fire, explosion or other dangers.
Support
lf you encounter any problems in using the product arneed any help, pleasecontact Hollyland Support Team via the following ways:
Hollyl and Products User Group
Hollyl and Tech
HollylandTech
Support@hollyland-tech.com
www.hollyland-tech.com
Statement:
All copyrights belong to Shenzhen Hollyland Technology Co.,LTD.
Trademark Statement:
Without the written approval of Shenzhen Hollyland Technology Co.,LTD, no
organization or individual may copy or reproduce part or all of the content of
the textwithout authorization , and may not disseminate it in anty form.
organization or individual may copy or reproduce part or all of the content of
the textwithout authorization , and may not disseminate it in anty form.
Note:
Due to product version upgrades or other reasons, this quick guide will be
updatedfrom time to time.Unless otherwise agreed,this document is provided as
aguidefor use only. All representations, information, recommendations in this
documentdo not constitute warranties of any kind , express orimplied.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The device has been tested and comply with FCC SAR limits
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
References
- Hollyland - Wireless Video Transmitter, Intercom, Microphone
- Hollyland - Wireless Video Transmitter, Intercom, Microphone
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>