Knightsbridge OSMKW Smart Motion Sensor User Guide
- June 15, 2024
- Knightsbridge
Table of Contents
Knightsbridge OSMKW Smart Motion Sensor
USER GUIDE
Download the SmartKnight App
On Google Play (AndroidTM) or App Store® (Apple®).
Open the app, tap “Register” and follow the on-screen instructions
Add Device
(2.4 Ghz only)
To add a device tap the “+” on top right corner, select the product category
and follow the on-screen instructions
Enjoy
Enjoy your connected product. For more in-depth instructions, please see
section titled “Wi-Fi Control” in this leaflet
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by
the end-user for future reference and maintenance.
These instructions should be used to aid the installation of the following
product: OSMKW
SAFETY
- Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
- This product is IP20 rated
INSTALLATION
Note : Please avoid installing the sensor within the proximity of reflective surfaces, direct airflow from vents, fans, windows, sources of steam, infrared light sources and objects causing changes of temperatures like heaters, refrigerators, and ovens.
Ensuring not to infringe with any gas / water pipes or electrical cables drill a hole into the installation area and affix the magnet with the included fixing screw and wall plug (see Fig.1)
Note : We recommend a walk test be carried out after the installation to ensure the desired area is covered, if not, the angle of the sensor can be adjusted to obtain the desired detection area
BATTERY INSTALLATION
Using the included screwdriver, unscrew the back of the sensor, replace the batteries ensuring the correct polarity is observed, and re-fit the back of the sensor (see Fig. 2)
WI-FI CONTROL
- Download the SmartKnight app on Google Play or the App Store
- Once the app is downloaded, open the app and tap “Register” then follow the on-screen instructions
- To add a sensor to the app, ensure that the sensor is powered and tap “+” on the top right corner
- Tap “Motion Sensor”
- If the indicator is flashing rapidly, please skip the reset procedure and tap “Confirm the indicator is flashing rapidly”. If the indicator is not flashing, follow the on-screen instructions to reset it
- Connect to the desired Wi-Fi network, tap “Confirm” and the app will start searching for devices. Please note only 2.4 GHz networks are supported and make sure your device is connected to the same Wi-Fi network
- After the sensor has been added successfully to the app, it can be named and added to a room. After naming it, tap “Done”
GENERAL
This product should be recycled in the correct manner when it reaches the end
of its life. Check local authorities for where facilities exist.
The batteries in this sensor are Alkaline and must be disposed of correctly.
Please contact the local authorities for the disposal of this toxic waste
WARRANTY
This product has a warranty of 2 years (excluding battery) from date of purchase. Improper use or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period it should be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior notice.
ML Accessories Limited LU5 4LT www.mlaccessories.co.uk
Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with CE marking
ML Accessories Ltd. Declare that all products have been designed,
manufactured, and tested in accordance with the requirements of the relevant
legislation
CE marking legislation
In Accordance with the following Directives:
2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive
2014/53/EU Radio Equipment Directive
Including Legislation
1907/2006 REACH
2015/863 RoHS
2021/341 ERP
Safety Standards
Full individual declarations and specific safety standards applicable to
relevant product series can be found on our website
www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply with the relevant sections of the above referenced specifications. The product complies with all essential requirements of the directives.
Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with UKCA marking
ML Accessories Ltd. declare that all products have been designed,
manufactured, and tested in accordance with the requirements of the relevant
legislation
UKCA marking legislation
UK SI 2016 No. 1091 Electro Magnetic Compatibility Regulations 2016
UK SI 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016
UK SI 2012 No. 3032 Restriction of the use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
UK SI 2017 No. 1206 Radio Equipment regulations 2017
UK SI 2021 No. 1095 The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021
Included Legislation
UK SI 2008 No. 2852 UK REACH
UK SI 2013 No. 3113 WEEE
Safety Standards
Full individual declarations and specific safety standards applicable to
relevant product series can be found on our website
www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply
with the relevant sections of the above referenced specifications. The
products comply with all essential requirements of the directives.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>