GLAKER K11S Hair Clippers for Men Instruction Manual

GLAKER K11S Hair Clippers for Men

IMPORTANT SAFEGUARDS

1. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
2. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
3. This appliance contains batteries that are non-replaceable. When the battery is at the end of its life, the appliance shall be properly disposed of.
4. The appliance must only be supplied at safety extra low voltage corresponding to the marking on the appliance.
5. The power supply with output power not exceeding 15W in normal and abnormal working conditions must be used.
6. WARNING: Keep the appliance dry.
7. WARNING: Cutting blades may become hot after prolonged use.
8. WARNING: Do not use this appliance near bathtubs, showers, basins or other vessels containing water.
9. Keep appliances out of reach from young children, particularly during use.
10. Do not expose the appliance or battery to excessive temperatures.
11. Be aware of the risk of terminals of the battery-operated appliance or battery being short circuited by metal objects.
12. There is a built-in rechargeable lithium battery in the product. When disposing of the hair clippers, do not mix them with general household waste. It should be sent to the battery recycling centre for disposal in accordance with local disposal management regulations.

SAVE THESE INSTRUCTIONS
Recycling and environmentally Friendly Disposal
In order to protect the environment, after the expiration of the product’s service life, it should not be discarded in the same way as domestic garbage; please recycle it at a professional recycling centre. For further information on the recycling of this product, please consult your local municipality, processing service centre, or the store where you purchased the product. You can help protect the environment! Please remember to respect the local regulations, and hand in the non-working electrical equipment to an appropriate waste disposal centre.

Components

Parameters

Precautions For Use

• DO NOT disassemble the product by yourself.
• DO NOT wash the hair clippers; keep them away from wet areas.

• The product should only be cleaned with a lightly dampened moist cloth or a mild soap solution.
• DO NOT charge the product within temperature ranges of above 40°C or below 0°C. Otherwise, the battery’s capacity will be reduced and its lifespan will be shortened.
• Output CANNOT exceed 5V, otherwise, the device will burn out, resulting in a permanent end to its operational life.
• The product will become warm during usage and charging, this is normal.
• Please remove the battery safely, and follow all proper protocols in your area or battery disposal, when the battery’s service life ends.

Instruction

LED Display

• Power Indicator Percentage.
• If there is a lack of oil, the red light on the left side of the clipper turns on and there is an audible reminder at the same time.
• If the battery is below 5%, the red light on the right will flash.

Fixed-Length Function

• A: Use of guide Combs: Crop and trim the hair Options: (1.5, 3, 4.5, 6, 10, 13, 16, 19, 22, 25, 32, 38, 51mm, Left&Right) 15 length adjustment options, they help to control the length of the hair that is cut.

1. To determine the length of the haircut
2. To select the appropriate guide Combs for styling and trimming.

• To adjust the clippers These clippers are equipped with an adjustable taper lever that changes the closeness of the hair trimming.
• When the lever is in the uppermost position, the blades will produce the closest trimming.
• Pushing the lever downward gradually will increase the cutting length, as a result, less hair will be cut.

Install the guide Comb

1. Align the guide Comb with the blade edge.
2. Slightly press down on it until there is a Snap in order to mount it.
   Disassemble the guide Comb: Pull the guide comb firmly at its base (not along the teeth) until it disconnects from the clippers.

Use the Rechargeable Mode

How To Recharge

1. Insert the charger into the rear port of the clippers, and connect to a power supply to begin charging.
2. When the charging indicator light comes on, charging has commenced; when the red light changes to blue, it indicates the product has been fully charged. Cord and cordless options are available.

Assembly & Disassembly Of The Clippers

• The blades must be realigned if they have been removed for cleaning or replacement.
• As shown in the image to the right the bottom blade holes are wider than the shanks of the blade screws. After the screw of the bottom blade is loosened, adjust the distance of the lower blade, and align it with the upper blade, then tighten it.

1. The end of the upper blade teeth should be 0.5mm away from the lower blade when the lever is in the uppermost position.
   This must be done so that the clippers will not cut too closely or allow any moving parts to come in contact with the skin.

2. The leftmost tooth of the upper blade must be covered or in the left position of the first small tooth of the bottom blade.

3. The rightmost tooth of the top blade must be touching the large tooth on the bottom blade.

Maintenance of Clippers

• The clippers have been carefully tested to ensure they are oiled and aligned properly before leaving the factory.
• To keep the clippers performing at the highest capacity they must be oiled after several uses.
• To oil it properly, the unit should be held so the blades are in a downward position. With the clipper blade running, dispense 2-3 drops of oil across the top blade.

WARRANTY

ONE-YEAR WARRANTY

• For more information, contact us at:
• E-mail: [email protected].
• UK | REP
• Company: Access AR Ltd
• Address: Office 3, 4a Nelson Road, London, SE10 9JB
• Email: [email protected].
• EC | REP
• Company: Enbaoxin Germany Maternal and Infant Supplies GmbH
• Address: Laubenhof 23, 45326 Essen, Germany
• Email: [email protected].

MANUFACTURER

• NINGBO ICLIPPER ELECTRIC APPLIANCE CO., LTD.
• No.99 Zhongxing East Road, Xikou Town, Ningbo, Zhejiang, China
• MADE IN CHINA

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>