GLAKER I11 Professional Outliner Trimmer Instruction Manual

GLAKER I11 Professional Outliner Trimmer Instruction Manual

IMPORTANT SAFEGUARDS

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack  of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
2. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
3. This appliance contains batteries that are non-replaceable. When the battery is at end of life, the appliance shall be properly disposed of.
4. The appliance is must only be supplied at safety extra low voltage corresponding to the marking on the appliance.
5. The power supply with output power not exceeding 15W in normal and abnormal working conditions must be used.
6. WARNING: Keep the appliance dry.
7. WARNING: Cutting blades may become hot after prolonged use.
8. WARNING: Do not use this appliance near bathtubs, showers, basins or other vessels containing water.
9. Keep appliance out of reach from young children, particularly during use.
10. Do not expose the appliance or battery to excessive temperatures
11. Be aware of the risk of terminals of the battery-operated appliance or battery being short circuited by metal objects.
12. There is a built-in rechargeable lithium battery in the product. When disposing of the hair clippers, do not mix it with general household waste. It should be sent to the battery recycling center for disposal in accordance with local disposal management regulations.
    SAVE THESE INSTRUCTIONS

Recycling & Environmentally Friendly Disposal
In order to protect the environment, after the expiration of the products service life, it should not be discarded in the same way as domestic garbage; please recycle at a professional recycling center. For further information on the recy- cling of this product, please consult your local municipality, processing service center, or the store where you purchased the product. You can help protect the environ- ment! Please remember to respect the local regulations, and hand in the non-working electrical equipment to an appropriate waste disposal center.

Component

• Combs

• Brush

• Standard 5V/USB charging port

Parameters

High performance motor
Battery| Capacity:1400mAh lithium battery
Power: 5W
Charging time: about 2 hours
Operating time with full charge: about 3 hours
Applicable Adapter Type| Input:100-240V 50/60Hz
Output: DC 5.0V 1A

Precaution for Use

DO NOT disassemble the product by yourself.
DO NOT wash the hair clippers; keep them away from wet areas.

**** The product should only be cleaned with a lightly dampened moist cloth or a mild soap solution.

**** DO NOT charge the product within temperature ranges of above 40°C or below O°C. Otherwise the battery’s capacity will be reduced and its lifespan will be shorten.

**** Output CANNOT exceed 5V, otherwise the device will burn out, resulting in a permanent end to its operational life.

• The product will become warm during usage and charging, this is normal
• Please remove the battery safely, and follow all proper protocols in your area or battery disposal, when the battery’s service life ends.

Instruction

Charging Indicator Light

1. When the power is less than 10%, the charging indicator lights begins flashing, indicating charging is needed.

Fixed Length Function

A: Use of guide Combs: Crop and trim the hair Options: (2,3,4mm) three length adjustment options, they help to control the length of the hair that is cut.

1. To determine the length of the haircut
2. To select the appropriate guide Combs for styling and trimming

**Mount the limit comb:

**

1. Align the limit comb with the blade edge
2. Slightly forward push to mount it. Disassemble the limit comb: Just pull hard the limit comb

Use the Rechargeable Mode

How to charge

1. Insert the charger into the rear port of clippers, connect to a power supply to begin charging.
2. When the charging indicator light comes on, charging has commenced; when the red light changes to blue, it indicates the product has been fully charged. Cord and cordless options are available.

Blade Removal and Installation

Blade Removal To remove the cutter head, use a screwdriver to unscrew the head.

To prevent the knife from falling, use another hand to hold it.

Blade Installation

The blade spring is aligned with the spring A on the knife head B. Then, put in two fixed screws, and hold down.

Tighten the screw with a screwdriver to ensure the head of clipper will not fall off.

Warm tip: Do not disassemble the clipper head without reading the guidance.

Cleaning and Maintenance of Clipper

Taper Blade Cleaning

Clear up the blade with cleaning brush Taper Blade Maintenance

Before or after use, maintain the blade by dripping some oil on the red point places like the left picture

ONE-YEAR WARRANTY

For more information, contact us at:
E-mail: Support@glaker.com

UK | REP
Company: Access AR Ltd
Address: Office 3, 4a Nelson Road, London, SE10 9JB
Email: info@accessar.co.uk

EC REP
Company: Enbaoxin Germany Maternal and Infant Supplies GmbH
Address: Laubenhof 23, 45326 Essen, Germany
Email: jasvigor2020@gmail.com

MANUFACTURER
NINGBO ICLIPPER ELECTRIC APPLIANCE CO.,LTD. No.99 Zhongxing East Road, Xikou Town, Ningbo, Zhejiang, China
MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>