COBY CSTV-130 Wireless TV Speaker User Manual

COBY CSTV-130 Wireless TV Speaker

In the box

• 1 x CSTV-130 Wireless TV Speaker
• 1 x Speaker Dock
• 1 x AC Power Adapter
• 1 x RCA Cable
• 2 × Micro USB Cable
• 1 x Optical Cable
• 1 x AUX Cable
• 1 × User Manual

Overview

1. Dock
2. TV Speaker
3. Dock LED Indicators – Indicates status of the Dock.
4. Pole Neverme Knob – Turns the Speaker on/off and adjusts
5. Speaker LED Indicators – Indicates status of the Speaker,
6. including 5 LEDS to indicate battery status, Mute Mode, Bluetooth mode, TV mode, Aux In mode.
7. Mute Button – Press to mute or resume sound for playback.
8. Headphone Output Jack – For listening TV audio with headphones.
9. Speaker Micro USB Charging Port – For charging the Speaker.
10. Dock Power Input Port (Micro USB) – Power input for the Dock.
11. headphone xirput reD Out -For playther devic from the
12. Optical Input Port – Alternate connector to TV audio.
13. Optical Input Port – Alternate connector to TV audio.
14. Mode/Standby Button (Dock) – Press repeatedly to toggle between TV Mode and Aux In Mode, press and hold to enter Standby Mode, the LED Indicator light of the dock will flash slowly and the speaker sound will be muted. You can press and hold this button again to resume Speaker sound.
15. Pair/Unpair button – For manually pairing the Speaker with the Dock or disconnecting the Speaker with the Dock.

Charging your Speaker

There are two methods for charging the TV Speaker.

Method 1. Connecting to an AC Power source

• Step 1. Connect the included power adapter to the USB end of the included Micro USB cable.
• Step 2. Plug the Micro USB end of the connected AC power cable to the Speaker Micro USB Charging port, or to the Dock Power Input Port and place the TV Speaker onto the Dock with the two metal pins aligned.
• Step 3. Plug the other end of the power cable to an AC power source to begin charging.

Method 2. Connecting to a USB power source

• Step1. Connect one end of the included Micro USB Cable to the Speaker Mirco USB Charging Port, or to the Dock Power Input Port (5V, Micro USB Port) and place the TV Speaker onto the Dock.
• Step 2. Connect the other end of the cable to a USB power source to begin charging.

Note: Some TVs come with USB power output port, you can also direct-ly plug the USB end of the included Micro USB cable into the TV’s USB port to charge the speaker. Make sure your TV’s USB power output is 5V/1A so that it can power the dock on, refer to your TV’s user manual.

Battery status indication on Speaker LED

Powering On/Off

1. Power the Speaker on/off
   • To power on the Speaker, turn the Power/Volume button clockwise until you hear a click.
   • To power off the Speaker, turn the Power/Volume button counter clockwise until you hear a click.
2. Power the Dock on/off
   • To power on the dock, connect the supplied charging cable to the DC 5V Power Jack of the Dock and to an power source. If the Dock is powered on, the Dock LED Indicator will light up.
   • To power off the Dock, disconnect the charging cable from the power source.
   • To set the Dock to Standby Mode, press and hold the Mode/Standby Button on the Dock until the Dock LED Indicator slowly flashes.

Pairing your Speaker and the Dock

When the Speaker and Dock are both powered on, they will pair together automatically. If they are successfully paired, you will hear the sound for the audio playback from the TV speaker while you connect the dock to an audio source.

Connections

There are four methods available for connecting the TV speaker, you can use any of the connection methods listed down to connect the TV speaker to your desired audio source.

Connect to the Optical port of the Dock through an optical cable

1. Step 1. Pull out and remove the rubber protector nubs on both ends of the supplied Optical Cable.
2. Step 2. Connect the included Optical Cable to the Optical Port of the Dock and to your TV’s Optical Port.
3. Step 3. Press the MODE Button on both the Speaker and Dock to sel ect TV Mode, the TV LED Indicator on both the Speaker and Dock will turn orange.
4. Step 4. Make sure the audio settings on your connected TV are set to PCM or Optical audio format. Note: If your TV has the sound settings set to Dolby or another format, your Speaker may not function properly. You must change
   the sound output to PCM or Optical audio. Refer to your TV’s user manual.

Connect to the Line In port of the Dock through an AUX cable or AUX+ RCA cable

• Step 1. Connect one end of the included AUX Cable to the Line In (AUX In) port of the Dock and to the Headphone Output or AUX Out port of your device (Like your TV, DVD player, smart phone, laptop etc.).

If your TV or DVD player has RCA Audio Out ports, you can use the included RCA cable (Red colored connector for right audio channel, white colored connector for left audio channel) to connect with the AUX cable, as shown in the following figure below.

Step 2. Press the Mode Button repeatedly on the Dock to select Line In Mode and on the speaker to select TV Mode, the Line In LED Indicator on the Dock will turn green, the TV LED indicator on the speaker will turn orange.

Step 3. Make sure the audio settings on your connected TV are set to PCM or Optical audio format.

Connect to the Line In port of the Speaker through an AUX cable or AUX+ RCA cable

Step 1. Connect one end of the included AUX Cable to the Line In (AUX In) Port of the Speaker and to the Headphone Output or AUX Out port of your device (Like your TV, DVD player, smart phone, laptop etc.).

If your TV or DVD player has RCA Audio Out ports, you can use the included RCA cable (Red colored connector for right audio channel port, white colored connector for left audio channel port) to connect with the AUX cable, as shown in the following figure below.

Step 2. Press the Mode Button repeatedly on the Speaker to select Line In Mode, the Line In LED Indicator on the Speaker will turn green.

Note: When an AUX cable is connected, it will automatically unpair from any actively paired Bluetooth® device.

Bluetooth connection with your device

Step 1. Press the Mode Button on the Speaker to select and enter Bluetooth Mode, the Bluetooth LED Indicator on the Speaker will rapidly flash blue.

Step 2. Turn on Bluetooth in your device’s settings and search for “CSTV-130”, then tap “CSTV-130” to connect.

If the Speaker is successfully paired with your media device, the Blue-tooth LED Indicator on the Speaker will glow solid blue, and you will hear a tone notification.

Notes

1. If there is no operation for more than 15 minutes after you select Bluetooth mode, the TV speaker will automatically enter Standby mode, then the Bluetooth LED Indicator light will be off, and the Mute LED indicator will glow red. To enter Bluetooth mode, you need press the Mode button again to select it.
2. The Speaker will automatically be paired with your last successfully connected media device next time they are both turned on.

Audio playback

Once your Speaker is connected to an audio device using any of the connection modes listed above, music and other audio will be play-able and controlled through that device. There are some controls that can be performed on the Speaker itself.
To raise or lower the volume of the Speaker, turn the Power/Volume Knob clockwise or counter clockwise.

To mute or resume your music sound, press the Mute Button once.

1. During audio playback, please do not press and hold the Mute button for more than 2 seconds, otherwise the speaker will unpair with the dock.
2. The Speaker can be used to play audio both on its own and while connected to the Dock (Please note that the distance between the speaker and dock should be within 100 feet.).

Listening music with your headphones
Connect wired headphones or earbuds to the Headphone Output Jack on the Speaker. You can use the Speaker’s Volume Knob and Mute Button here as well.

Troubleshooting

Bluetooth mode is not working.

| 1.   On your phone’s Bluetooth set- tings, tap Forget the device to clear the Speaker’s Bluetooth connection from your device.

2.        Turn your phone’s Bluetooth off, then turn it on again.

3.           Ensure your Speaker is set to Blue- tooth mode, search for “CSTV-130”, then tap “CSTV-130” to reconnect.

The Speaker will not pair with the Dock automat- ically.

| Step 1: Turn on the speaker, press the MODE button on the Speaker to select TV Mode, then press and hold the Mute button for 2-3 seconds.

Step 2: Connect the dock to the power source, make sure that your dock is connected to the TV with an optical cable (then switch the dock to TV mode), or is connected to your audio device with an AUX

cable (then switch the dock to Line In mode), and use a metal pin to press the PAIR button to repair the Speaker and the Dock.

Audio from the Speaker sounds distorted.| Select PCM 2.0 (or PCM stereo) as the audio output.
The Speaker is not re- sponsive to any input.| Check if the Speaker’s battery is dead, and charge it if so.

Specifications

Safety Statement

Safety Precautions

1. Avoid dropping.
2. Do not disassemble this device.
3. Do not expose this device to rain or moisture or submerge in water.
4. Ideal temperatures are 0°C to 35°C. Avoid extreme temperatures.
5. Keep the device away from excessive heat, such as sunshine, fire or the like.
6. Do not use the device outdoors during thunderstorms.
7. Use original or certified cables.
8. The Power Adapter is used as the disconnect device for the dock. Ensure that the socket outlet is easily accessible after installation.
9. Hands must be dry when plugging the power cord into an AC outlet to prevent electrical shock. Do not damage the power cord by disassembling, bending, pulling or exposing it to heat as it may cause a fire or electrical shock.
10. Make sure to completely insert the power plug into an AC outlet. Insecure connections can cause a fire.
11. Do not use any corrosive cleaner/oil to clean.
12. To prevent damage to your device’s parts or internal circuits, do not use it in dusty, smoky, damp or dirty environments.
13. Do not use, store or transport the device where flammables or explo-sives are stored. Using your device in these environments increases the risk of explosion or fire.

FCC Statement

FCC ID: 2AMSOCSTV-130
This device complies with Part 15 of the FCC Rules. Operation is sub-ject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency en-ergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to ra-dio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the in-terference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an out-let on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician for help.

FCC Radiation Exposure Statement

• The device has been evaluated to meet general RF exposure requirement.
• The device can be used in portable exposure condition without restriction.

Notice: This product complies with the radio interference require-ments of the European Community.
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling.
Follow local rules and never dispose of the product and re-chargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Disclaimer
All information, design and specifications contained in this manu-al were correct at the time of this publication. As the product goes under continuous upgrades and changes, however, the final device may have slight differences. The contents of this manual are subject to change without prior notice, and Fesco Group will not be liable for any errors contained herein or for incidental or consequential dam-ages in connection with the furnishing performance or use of this manual.
COBY COPYRIGHT 20© 22 ALL RIGHTS RESERVED. COBY IS A REGISTERED TRADEMARK OF CBY HOLDINGS, LLC. MANUFAC-TURED BY SUMMIT ELECTRONICS LLC. USED UNDER LICENSE. CBY HOLDINGS, LLC DOES NOT MANUFACTURE THIS PROD-UCT OR PROVIDE ANY MANUFACTURER’S WARRANTY OR SUPPORT. THE BLUETOOTH® WORD MARK AND LOGOS ARE REGISTERED TRADEMARKS OWNED BY THE BLUETOOTH SIG, INC. AND ANY USE OF SUCH MARKS BY SUMMIT ELECTRON-ICS LLC IS UNDER LICENSE. OTHER TRADEMARKS AND TRADE NAMES ARE PROPERTY OF THEIR RESPECTIVE OWNERS.

WARNING: CANCER AND REPRODUCTIVE HARM – WWW.P65WARNINGS.CA.GOV.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Fesco Distributors, Inc. is under license. Other trademarks and trade names are those of their respective owners.

Warranty

SUMMIT ELECTRONICS LLC One Year Limited Warranty
WARRANTY SUMMIT ELECTRONICS LLC LIMITED WARRANTY (“Warranty”) – For product Categories Listed in Chart Below (as ap-plicable, “Product”) Before returning your Product for service under this Warranty, please (i) read the instruction manual carefully. If you are still having trouble with your Product, please contact Technical Support at helpdesk@summitcegroup.com.

Warning: Some Products may contain components that are small enough to be swallowed. Please keep out of reach of children. Subject to the terms and conditions herein, SUMMIT ELECTRONICS LLC (hereinafter called “SUMMIT ELECTRONICS LLC”) warrants to the original purchaser of the Product (“Customer”) that for the ap-plicable Warranty Period listed below, the Product will be free from defects in material or workmanship under normal, non-commercial use (“Defects”).

Warranty Period encompasses, as listed below, separate “Coverage Periods” for Parts and Labor, each Coverage Period for one year, to be-gin from the original date of Customer purchase. If Customer returns a defective Product (or any component thereof) during the applica-ble Warranty Period, SUMMITELECTRONICSLLC will, at its option, during the specified Coverage Periods for Parts and Labor (as appli-cable) either: (i) repair the Product (or, as applicable, any component thereof) or (ii) replace the Product (or, as applicable, any compo-nent thereof) with a new or refurbished Product (or, as applicable, any component thereof), in either case free of charge to Customer for Parts and/ or Labor (as applicable) during the specified Coverage Period only, and excluding applicable shipping charges (noted below), for which the Customer is responsible. The foregoing states the Cus-tomer’s exclusive remedy and SUMMIT ELECTRONICS LLC’s sole lia-bility for breach of the limited warranty contained herein.

This Warranty specifically excludes any Product (or, as applicable, any component thereof) that has been subject to or Defects resulting from: (a) any neglect or misuse by a Customer, an accident, improper application, violation of operating instructions for the product, any other Customer-induced damage, or the alteration or removal of any product serial number: (b) any modification or repair to Product (or, as applicable, any component thereof) by any party other than SUM-MIT ELECTRONICS LLC or a party authorized in writing by SUMMIT ELECTRONICS LLC; (c) any damage to Product (or, as applicable, any component thereof) due to power surges, incorrect electrical voltage, misconnection 17 to any device, or malfunction of any device used with the Product (or, as applicable, any component thereof); (d) cos-metic damage to the Product (or, as applicable, any component there-of) caused by normal wear and tear; (e) shipping damage that occurs while the Product is in transit; (f) damage caused by heat sources, sunlight, electromagnetic conditions, or other climatic conditions; or (g) any acts of God. Product is sold to Customer for personal, non-commercial use only. Product is not warranted for Customer’s commercial or rental use.

In addition, Product is not warranted against failure, and should not be used by Customer for any application where (i) there is a risk that any data stored on Product will be breached or otherwise compro-mised, or (ii) the data stored on Product is relied upon for medical or lifesaving applications. SUMMIT ELECTRONICS LLC disclaims any Warranty for any of the foregoing uses to the fullest extent permit-ted by law. Customer assumes any and all risks associated with such uses of Product and agrees to indemnify SUMMIT ELECTRONICS LLC for any damages claimed against SUMMIT ELECTRONICS LLC for such uses.

EXCEPT FOR EXPRESS WARRANTIES STATED ABOVE AND TO THE MAXIMUM EXTENTPERMITTED BYLAW, THE PROD-UCTS ARE PROVIDED “AS IS”, AND SUMMIT ELECTRONICS LLC DISCLAIMS ALLOTHER WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY(I) OF ERCHANTABILITY, (II) OF FITNESS FOR APARTICULAR PURPOSE, OR (III) OF NON-IN-FRINGEMENT OF THIRD-PARTY RIGHTS. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL SUMMIT ELECTRO- NICS LLC BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY INDIRECT, SPECIAL, INCIDENTAL, CON-SEQUENTIAL, EXEMPLARY OR PUNITIVE DAMAGES, INCLUD-ING, WITHOUT LIMITATION, ANY LOST PROFITS OR REVENUES, LOSS OR INACCURACY OF ANY DATA OR COST OF SUBSTITUTE GOODS, REGARDLESS OF THE THEORY OF LIABILITY (INCLUD-ING NEGLIGENCE) AND EVEN IF SUMMIT ELECTRONICS LLC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, SUM-MIT ELECTRONICS LLC’S AGGREGATE LIABILITY TO CUSTOMER FOR ACTUAL DIRECT DAMAGES FOR ANY CAUSE WHATSOEVER SHALL BE LIMITED TO THE CUMULATIVE PRODUCT FEES PAID BY THAT CUSTOMER FOR THE PRODUCT CAUSING THE DAMAGES, IF ANY.

This Warranty gives Customer specifics rights, and Customer may also have other rights that vary from jurisdiction to jurisdiction. To obtain Warranty service, Customer must email SUMMIT ELEC-TRONICS LLC Technical Support prior to making a Product return. Customer must include with Product return the following items (fail-ure to enclose any of these items may result in a delay in the process-ing of your Warranty claim): (i) a dated sales receipt that indicates the place of purchase, model number of Product, and amount paid; (ii) a detailed description of Customer’s problem with Product; (iii) Customer’s full name, phone number, and return address, and; (iv) a money order made out to SUMMIT ELECTRONICS LLC Electronics Corporation to cover return shipping charges to US destinations only, for the applicable dollar amount shown for the Product in the table above. SUMMIT ELECTRONICS LLC will not make return shipments to a P.O. Box. For shipping to international addresses, actual freight will be charged to Customer. Return your Product freight-prepaid in its original packaging, or packaging that affords an equal measure of protection. Please allow 4 to 6 weeks for the processing of your claim (6 to 8 weeks from November to February).

You must email SUMMIT ELECTRONICS LLC Technical Support prior to making a return.Please ask if you are unsure of which category your product falls under. *US destinations only.

Customer Service

Servicio al Cliente

To get the best after-sales service, access the Contact webpage from the link:
https://summitcegroup.com/pages/contact. Call us at 833-212-0258 or email us at helpdesk@summitcegroup.com for return information and customer support!

For more information, please visit: Para mayor información por favor visite: summitcegroup.com

Version No.:V1.2
Date code:2022-12

References

• P65WARNINGS.CA.GOV
• Summit Electronics LLC
• Contact – Summit Electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>