IASUS IA-RK-BASIC-BT XSound 3 Dual Pack Instruction Manual

June 4, 2024
IASUS

IASUS IA-RK-BASIC-BT XSound 3 Dual Pack

PACKAGE CONTENTS

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-FIG-1

  1. RE KON Interface
  2. Control Dial
  3. Center Button
  4. Quick Release Clip
  5. LED Indicators
  6. Interconnect Cable
  7. Mount for REKON Interface
  8. RE KON Base
  9. Microphone
  10. 3.5mm Audio Output Connector
  11. Magnetic Charging Port
  12. Connector from Helmet Speakers (Helmet Speakers not included)
  13. Charging Cable
  14. 3M Velcro Adhesive (Loop)
  15. 3M Velcro Adhesive (Hook)

TIP: REKON comes charged and ready to use.

SPECIFICATIONS

Bluetooth Low Energy

SUPPORTED PROFILES

  • AVRCP 1.6: HSP 1.2
  • A2DP 1.3.1: SPP 1.2
  • HFP 1.7: BLE 5.0

BATTERY

  • PLAYBACK TIME . …………………. 9HOURS
  • CALL TIME . ……………………………. 10HOURS
  • STAND-BY TIME …………….. .250HOURS
  • CHARGING TIME . …………. 90 MINUTES
  • CHARGING SPECS …………………………….. SV
  • BATTER Y CAPACITY . ……………. 150mAh

STANDARD

Ingress Protection Rating against dust and water

ABOUT THIS MANUAL

Any references made to rotating the control dial to your left and right is from the viewpoint of wearing your helmet.

  1. INSTALLING REKON INTERFACE

REKON Interface is designed to be positioned on the outside front section of your helmet through the use of a quick-release clip mount for easy installation and removal.IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-
FIG-2

  • Clean the mounting surface of your helmet. Secure REKON Interface (1) to RE KON Mount (7).
  • Peel away the backing paper on REKON mount.
  • Position on your helmet and press firmly.

INSTALLING REKON BASE

REKON Base (8) can be installed inside the helmet either vertically or horizontally. Use the included Velcro adhesives for installation. The Velcro provides a quick release when removal is necessary. To allow REKON to fully capture your voice inputs, position the microphone (9) directly in line with your mouth. To maximize the microphone input capabilities, position the microphone (9) directly in line with your mouth.Provide sufficient space between the base and your mouth for both comfort and safety.

HORIZONTAL POSITION

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-FIG-4

  • Clean the mounting surface inside your helmet. Peel away the backing paper on the Hook Velcro (15) and attach it onto the REKON base.
  • Attach the Loop Velcro (14) horizontally to the inside of the chin guard. Position and install REKON Base onto the Velcro inside the helmet.

VERTICAL POSITION

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-FIG-5

  • Clean the mounting surface inside your helmet. Peel away the backing paper on the hook Velcro and place it onto the REKON Base.
  • Attach the Loop Velcro vertically to the inside of the chin guard. Position and install REKON Base onto the Velcro inside the helmet.

DETACHING REKON

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-FIG-6

  • To unclip REKON Interface {1) from its mount (7), lift the quick release clip {4) and slide RE KON to the side.
  • Then remove REKON Base {8) from its Velcro mount {14).

CHARGING REKON

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-FIG-7

  • REKON comes shipped with its battery charged and ready to use. When charging is needed, connect the included USB cable {13) to the Magnetic Connector (11) located on the bottom of REKON Base.
  • A full charge completes in about 90 minutes. The background LED on the Center Button will be red until it is fully charged, at which point turns blue. To extend the life of the battery, we recommend not using fast chargers (>S00mA). To avoid damage to the battery, refrain from draining completely to zero and leaving it uncharged for an extended amount of time. Keep RE KON fully charged if stored for extended periods of time.
  • The REKON battery is sealed inside the unit and is not user serviceable. Please contact IASUS for issues with the battery. For proper disposal of this product at the end of its working life, consult your local laws for proper electronics and battery recycling and disposal. If you are not sure, do not deposit in unsorted waste but drop it of at your local or regional collection point for recycling to prevent any possible harm to the environment or human health.

3. SMM AUDIO OUTPUT CONNECTOR

  • REKON is equipped with a 3.5mm audio output connector that is optimized for the following IASUS audio accessories:
  • XSound 3 – High Definition Helmet Speakers
  • XSound 2.1- Helmet Speakers
  • iA Waterproof Earbuds
  • Future IASUS helmet speakers and earbuds products
  • ASUS cannot guarantee the compatibility and sound quality of any third-party helmet speakers and earbuds when used with RE KON as they may not be acoustically tuned to IASUS audio standards.

BLUETOOTH PAIRING

TURN PAIRING MODE ON
Press and Hold Center Button for at least 3 seconds until the background LED flashes Red and Blue with an audible pairing tone.

PAIR DEVICE
Find “REKON” in the list of available devices in the Bluetooth menu of the device you are pairing. The IASUS REKON uses standard Bluetooth 5.0 protocols. When paired with newer devices, there is no need to enter a passcode. For older Bluetooth-equipped devices, enter the code “0000”.

PAIRING A SECOND DEVICE

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-FIG-11

TURN PAIRING MODE ON
The IASUS REKON allows for pairing with two Bluetooth-enabled devices at the same time (smartphone, GPS, mp3 player, etc.) To pair a second device, after REKON is paired with the first device, press and hold the Center Button for at least 3 seconds to get into pairing mode.

PAIR SECOND DEVICE
Find “REKON” in the list of available devices in the Bluetooth menu with the device you are pairing. The IASUS REKON uses standard Bluetooth 5.0 protocols. When paired with newer devices, there is no need to enter a passcode. For older Bluetooth-equipped devices, enter the code “0000”.

RECONNECT FIRST DEVICE
Pairing the second device will disconnect REKON from the first device-this is normal. Goto your first device’s Bluetooth settings and manually reconnect to RE KON.

CONTROLS

REKON interface is carefully designed and built on 3 main user actions to achieve a minimalistic appearance, yet still able to perform full Bluetooth functions. Any references made to rotating the Control Dial to your left and right is from the viewpoint of wearing your helmet.

  • Turning the Interface Dial to the left (counter-clockwise)
  • Turning the Interface Dial to the right (clockwise)
  • Pressing the clear Center Button

This RE KON Interface Dial is made of CNC aluminum and the Center Button cover from tempered glass. It is ergonomically designed to be easily operated, even with gloves.
The headset emits a beep tone to indicate a function has been activated by your input.

GETTING STARTED

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-
FIG-13

POWER ON

POWER OFF
Rotate Dial left & hold until blue LED stops flashing

volume
Rotate Dial right once and release

VO LUME DOWN

Rotate Dial left once and release

MUSIC MODE

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-FIG-14

PL AY/ PAUSE MUSIC
Press Center Button once

PREVIOUS TRACK

Rotate Dial left twice and release

NEXT TRACK
Rotate Dial right twice and release

PHONE MODE

ANSWER/END CALL

Press Center Button once

REDIAL
Press Center Button twice

VOICE COMMAND

VOICE-ACTIVATED

  • Say ‘Hey Siri’ on iPhones or ‘Ok Google/Hey Google’ on Android phones
  • Ensure that Voice Command is activated in your device’s setti113S menu.

VOICE COMMAND

Rotate Dial right & hold for 2 seconds or until voice assistant is activated

VOLUME LEVELS

ON MUSIC MODE & PHONE MODE
During Music Mode (music playback), REKON’s volume level is adjusted independently of the phone’s Bluetooth playback volume. During a phone call, REKON’s volume and the phone’s volume are linked, following standard Bluetooth protocol.
TIP: If you experience low volume on Music Mode, be sure the volume is turned up on your phone as well as on REKON. Example: When adjusting REKON’s volume in Music Mode, the phone’s Bluetooth volume is not affected. However, in Phone Mode, adjusting REKON’s volume during a call affects the phone’s Bluetooth volume as well.

LED INDICATOR DEFINITION

IASUS -IA-BASIC-BT-XSound-3-Dual-Pack-FIG-16

  • REKON ON, BUT NOT PAIRED WITH ANY BLUETOOTH DEVICE
  • PAIRED
  • PHONE OR MUSIC PROFILE CONNECTED
  • PLAYING BACK MUSIC
  • N A PHONE CALL
  • PAIRING MODE. REKON READY TO PAIR WITH DEVICE
  • LOW BATTERY
  • CHARGING
  • REKON OFF
  • FINISH CHARGING

TROUBLESHOOTING

I paired REKON to my PC and when Windows tried to automatically install the drivers for REKON, it comes back with multiple “Bluetooth Peripheral Device – No Driver Found” errors.
Where can I find the drivers?
REKON’s charging light remains red and does not turn blue. REKON’s volume when playing music is very low.

This means Windows was notable to find any Bluetooth drivers for your PC hardware. Please ensure you have your computer manufacturer’s Bluetooth software suite installed and try to pair REKON again. It should automatically install all Bluetooth related functional­ities of REKON upon pairing. Ensure you’re using a charger with an output of S00mA or less. If problem persists, contact IASUS customer support. During Music Mode (music playback), REKON’s volume level is adjusted independently of the phone’s Bluetooth playback volume. If you experience low volume on Music Mode, be sure the volume is turned up on your phone as well as on the RE KON.

1-YEAR LIMITED WARRANTY

IASUS Concepts Limited warrants that the IASUS RE KON sold by IASUS Concepts or its authorized agents is free from defects in materials and workmanship under normal use for one year. This warranty is only applicable to the original purchaser in possession of a dated sales document receipt that includes the name and the company from which it was purchased. This warranty is in lieu of and excludes all other warranties, expressed or implied, including any implied warranty of merchantability or fitness, and of any other obligation on the part of IASUS Concepts Limited.
WHAT THIS WARRANTY DOES NOT COVER

  • Damage from improper operation, misuse, neglect such as dropping the product onto hard surfaces, contact with extreme humidity or heat, or acts of nature (lightning, floods, power surges, etc.).
  • Products that may have been tested, adjusted, installed, maintained, repaired or altered in any way by persons not expressly approved by IASUS Concepts Limited.
  • Cords that are stretched, burnt, torn or cut.
  • Products purchased more than 12 months previous to the current date.
  • Products that are not accompanied by a valid proof of purchase.

TO REGISTER FOR YOUR WARRANTY
You must register your product to receive warranty service. To do so and to view detailed information about our warranty service, please visit:
HTTPS:!aliases-concepts. comlwarran ty!
TO GET WARRANTY SERVICE FROM IASUS CONCEPTS
Please contact our customer service department via our website. Once you have done so, you will receive instructions on how to ship the products to IASUS Concepts or to one of our designated service centers. If instructed to ship the product, you must ship it with freight, duties and insurance prepaid. Regardless of where you are instructed to ship your product, you must include:

  • A copy of your dated sales document receipt
  • A fully completed Return Materials Authorization (RMA) form.
  • Payment for any services or repairs not covered by the warranty. This will have been predetermined with your customer service representative.

LEGAL INFORMATION

There is no informal dispute settlement mechanism available. This warranty gives you specific legal rights, and you may also have other rights, which vary geographically. Some areas do not allow limitations on how long an implied warranty last and/or do not allow the exclusions or limitations or consequential damages. IF this is true for your area, the above limitations or exclusions may not apply to you. lASUS Concepts shall not be liable for any special or consequential damages or for loss or expense directly or indirectly arising from use of the product, inability yi yuse the product in combination with other equipment, or from any other cause. IASUS Concepts reserves the right to make changes in the design of the product and to make additions or improvements to it without incurring any obligation to modify any products previously sold.

FOR LASTEST NEWS AND PRODUCTS, FOLLOW US ON SOCIAL MEDIA

MODEL NUMBER: IA-RK-BASIC-BT
Thank You for choosing the IASUS REKON Communicator Headset, a precision crafted, functionally packed, personal communication device designed for your helmet.
In this manual, you will find instructions to operate your REKON Communicator Headset with Bluetooth enabled devices. Should you have any questions and require assistance with setup and usage, please feel free to visit our website: WWW.IASUS-CONCEPTS.COM. or contact us directly at: info@iasus-concepts.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals