Honeywell C7089R3013 Wireless Outdoor Sensor Installation Guide

Honeywell C7089R3013 Wireless Outdoor Sensor

Product Information

Specifications

• Product Name: T10+ Thermostat

• Model Number: M38084A

• Optional Components: THM04R EIM (Equipment Interface Module), Outdoor Air Sensor

• Compatible Thermostat Models: THX321WFS3001W, THX321WF3003W,
  YTHM1004R3000, YTHM1004R3001

• Battery Type: 2 AA Lithium Batteries

Installation Guide

Procedure:

1. Install batteries in the RedLINK 3.0 outdoor sensor. Refer to page 2 for battery installation instructions.
2. Link the RedLINK 3.0 wireless outdoor sensor to the T10+ thermostat. Follow the steps below:
3. Open the menu on the T10+ thermostat.
4. Select “Devices & Sensors”.
5. Select “Add”.
6. Follow the on-screen instructions to complete the linking process.
7. Mount the outdoor sensor on a vertical exterior wall, at least 6 inches below any overhang. Choose a location protected from direct sunlight. Refer to page 3 for mounting instructions.

Note: If there are multiple T10+ thermostats, each wireless device must be linked separately to each thermostat. A maximum of eight T10+ thermostats can be linked to the C7089R3013 sensor.

Replacing System Components

If you need to replace system components, refer to page 5 for instructions.

FAQs

Q: How many T10+ thermostats can be linked to the C7089R3013 sensor?

• A : A maximum of eight T10+ thermostats can be linked to the C7089R3013 sensor.

Q: What type of batteries should be used for the outdoor sensor?

• A: The outdoor sensor requires 2 fresh AA lithium batteries.

Q: How can I delete the outdoor sensor from the T10+ thermostat?

• A : To delete the outdoor sensor, follow these steps on the T10+ thermostat:

1. Open the menu.
2. Choose “Installer options” and enter the passcode.
3. Select “Devices & Sensors”.
4. Select “Outdoor Sensor”.
5. Select “Delete”.

• After deleting the outdoor sensor, you can add a new one by following the instructions on page 2.

Q: What are the FCC compliance regulations for the outdoor sensor?

• A: The outdoor sensor complies with Part 15 of the FCC Rules. It must not cause harmful interference and must accept any interference received. To comply with FCC and Industry Canada RF exposure limits, the antenna(s) used for these transmitters must be installed with a separation distance of at least 20 cm from all persons and must not be co-located or operating with any other antenna or transmitter.

Q: What are the operation conditions for the device according to RSS-GEN?

• A: The device must not cause interference and must accept any interference, including interference that may cause undesired operation of the device.

OVERVIEW

If there is more than one T10+ thermostat:

• Wireless devices must be linked separately to each T10+ thermostat (eight T10+ thermostats max per C7089R3013 sensor).

Use C7089R3013 RedLINK 3.0 wireless outdoor sensor with up to eight compatible T10+ thermostat models

Install batteries in wireless outdoor sensor

• Make sure batteries are inserted properly. (See polarity marks on the illustration below.)

Link RedLINK 3.0 wireless outdoor sensor to T10+ thermostat

At T10+ thermostat:

1. Open the menu.
2. Tap Devices & Sensors.
3. Tap Add.
4. Follow the on-screen instructions.

Mount outdoor sensor

• Mount the sensor on a vertical exterior wall, at least 6 inches below any overhang. Choose a location protected from direct sunlight.

Replacing outdoor sensor

At T10+ thermostat:

1. Open the menu.
2. Choose the Installer option and enter the passcode.
3. Tap Devices & Sensors.
4. Select Outdoor Sensor.
5. Select Delete.

After the outdoor sensor has been deleted you can add a new outdoor sensor by selecting “Add” as shown on

Regulatory information

FCC Compliance Statement

(Part 15.19) (USA only)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Outdoor sensor

• To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-
• located or operating in conjunction with any other antenna or transmitter.

Section 7.1.5 of RSS-GEN

Operation is subject to the following two conditions:

1. this device may not cause interference,
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Need Help?

• For assistance with this product please visit http://customer.resideo.com or call Customer Care toll-free at 1-800-468-1502
• www.resideo.com
• Resideo Technologies, Inc.
• 1985 Douglas Drive North, Golden Valley, MN 55422
• 1-800-633-3991
• 33-00604EFS—05 M.S. Rev. 10-22 | Printed in United States
• © 2022 Resideo Technologies, Inc. All rights reserved.
• The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.
• Todos los derechos reservados. La marca comercial Honeywell Home se utiliza bajo licencia de Honeywell International, Inc.
• Este producto es fabricado por Resideo Technologies, Inc. y sus afiliados.

If there is more than one T10+ thermostat:

• Wireless devices must be linked separately to each T10+ thermostat (eight T10+ thermostats max per C7089R3013 sensor).

References

• Resideo Customer Portal
• Smart Home Solutions in EMEA | Resideo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>