ViewSonic VA1903H Widescreen Monitor User Guide

ViewSonic VA1903H Widescreen Monitor

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our website at http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Thank you for choosing ViewSonic

As a world-leading provider of visual solutions, ViewSonic is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic product you have chosen will serve you well. Once again, thank you for choosing ViewSonic!

Compliance Information

NOTE: This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU.

The following information is only for EU-member states: The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but to use the return and collection systems according to local law.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive), and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance| Proposed Maximum Concentration| Actual Concentration
---|---|---
Lead (Pb)| 0.1%| < 0.1%
Mercury (Hg)| 0.1%| < 0.1%
Cadmium (Cd)| 0.01%| < 0.01%
Hexavalent Chromium (Cr6+)| 0.1%| < 0.1%
Polybrominated biphenyls (PBB)| 0.1%| < 0.1%
Polybrominated diphenyl ethers (PBDE)| 0.1%| < 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
2. Short length (≦500 mm): maximum 3.5 mg per lamp.
3. Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
4. Long length (＞1,500 mm): maximum 13 mg per lamp.
5. Lead in glass of cathode ray tubes.
6. Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
7. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
8. A copper alloy containing up to 4% lead by weight.
9. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
10. Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectric devices, or in a glass or ceramic matrix compound.

Indian Restriction of Hazardous Substances

Restriction on Hazardous Substances statement (India) This product complies with the “India E-waste Rule 2011” and prohibits the use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

Cautions and Warnings

1. Read these instructions completely before using the equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings and followed all instructions.
4. Sit at least 18” / 45cm from the display.
5. Always handle the display with care when moving it.
6. Never remove the rear cover. This display contains high-voltage parts. You may be seriously injured if you touch them.
7. Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
8. Avoid exposing the display to direct sunlight or another heat source. Orient the display away from direct sunlight to reduce glare.
9. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display” in this guide for further instructions.
10. Avoid touching the screen. Skin oils are difficult to remove.
11. Do not rub or apply pressure to the display panel, as it may permanently damage the screen.
12. Do not block any ventilation openings. Install the equipment in accordance with the manufacturer’s instructions.
13. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.
14. Place the display in a well-ventilated area. Do not place anything on the display that prevents heat dissipation.
15. Do not place heavy objects on the display, video cable, or power cord.
16. If smoke, an abnormal noise, or a strange odor is present, immediately switch the display off and call your dealer or ViewSonic. It is dangerous to continue using the display.
17. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade and the third prong are provided for your safety. If the plug does not fit into your outlet, consult an electrician for replacement of the outlet.
18. Protect the power cord from being tread upon or pinched, particularly at the plug, and the point where if emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is easily accessible.
19. Only use attachments/accessories specified by the manufacturer.
20. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the equipment. When a cart is used, use caution when moving the cart/equipment combination to avoid injury from tipping over.
21. Unplug this equipment when it will be unused for long periods of time.
22. Refer all servicing to qualified service personnel. Service is required when the unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

Copyright Information

• Copyright © ViewSonic® Corporation, 2019. All rights reserved.
• Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.
• ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation.
• VESA is a registered trademark of the Video Electronics Standards Association. DPMS, DisplayPort, and DDC are trademarks of VESA.
• ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).
• As an ENERGY STAR® partner, ViewSonic Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
• Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
• In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.
• No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

• To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online.
• Registering your product will best prepare you for future customer service needs. Please print this user guide and fill the information in the “For Your Records” section. Your display serial number is located on the rear side of the display.
• For additional information, please see the “Customer Support” section in this guide. *Product registration available in selected countries only

For Your Records

• Product Name: VA1903h ViewSonic Widescreen Display
• Model Number: VS16216
• Document Number: VA1903h_UG_ENG Rev. 1A 03-13-18
• Serial Number:
• Purchase Date:

Proper product disposal is necessary at the end of product life
ViewSonic respects the environment and is committed to working and living green. Thank you for being part of a Smarter, Greener Computing effort.
Please visit the ViewSonic website to learn more.

• USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
• Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
• Taiwan: http://recycle.epa.gov.tw

Getting Started

Thank you for purchasing your monitor from ViewSonic®. At ViewSonic, we aim to provide the most stunning visual experience possible.

Package Contents

Your display package includes:

• Display
• Power cord
• Video cable
• Quick Start Guide

IMPORTANT:

• The word “Windows” in this user guide refers to the Microsoft Windows operating system.
• Visit the “Download” section of the monitor product page on the ViewSonic website to download your monitor drivers.
• Don’t forget to register your ViewSonic monitor! Simply login to the ViewSonic website in your region and click on the “Support” tab on the front page.
• Save the original box and all packing material for future shipping needs.

Quick Installation

Connect video cable

• Make sure both the display and computer are turned OFF.
• Remove rear panel covers if necessary.
• Connect the video cable from the display to the computer.
• Macintosh users: Models older than G3 require a Macintosh adapter. Attach the adapter to the computer and plug the video cable into the adapter. To order a ViewSonic® Macintosh adapter, contact ViewSonic Customer Support.

Connect power cord (and AC/DC adapter if required)

• Turn ON the display and computer
  Turn ON the display, then turn ON the computer. This sequence (display before computer) is important.
  NOTE: Windows users may receive a message asking them to install the INF file. To download the file, visit the “Download” section of the monitor product page on the ViewSonic website.

• Windows users: Set the timing mode (example: 1024 x 768) For instructions on changing the resolution and refresh rate, see the graphics card’s user guide.

• Installation is complete. Enjoy your new ViewSonic display!

Wall Mounting (Optional)

NOTE: For use only with a UL Listed Wall Mount Bracket. To obtain a wall- mounting kit or height adjustment base, contact ViewSonic® or your local dealer. Refer to the instructions that come with the base mounting kit. To convert your display from a desk-mounted to a wall-mounted display, do the following:

1. Verify that the power button is turned OFF, then disconnect the power cord.
2. Lay the display face down on a towel or blanket.
3. Remove the base (removal of screws might be required).
4. Find and identify one of the following VESA mount interfaces (a,b,c) located on the back of your display (refer to the “Specifications” page of your display’s mounting interface). Attach the mounting bracket from the VESA compatible wall mounting kit using screws of the appropriate length.
5. Attach the display to the wall, following the instructions in the wall-mounting kit.

Using the Display

Setting the Timing Mode

• Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain. The timing mode consists of the resolution (example 1024 x 768) and refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the OSD (On-screen Display) controls to adjust the screen image.
• For optimal picture quality, please use the recommended timing mode specific to your display listed on the “Specification” page.

To set the Timing Mode:

• Setting the resolution: Access “Appearance and Personalization” from the Control Panel via the Start Menu, and set the resolution.
• Setting the refresh rate: See your graphics card’s user guide for instructions.

IMPORTANT: Please make sure that your graphics card is set to 60Hz vertical refresh rate as the recommended setting for most displays. Choosing a non-supported timing mode setting may result in no image being displayed, and a message showing “Out of Range” will appear on screen.

OSD and Power Lock Settings

• OSD Lock: Press and hold [AUTO] and the up arrow for 10 seconds. If any other buttons are pressed the message OSD Locked will display for 3 seconds.
• OSD Unlock: Press and hold [AUTO] and the up arrow again for 10 seconds.
• Power Button Lock: Press and hold [AUTO] and the down arrow for 10 seconds. If the power button is pressed the message Power Button Locked will display for 3 seconds. With or without this setting, after a power failure, your display’s power will automatically turn ON when power is restored.
• Power Button Unlock: Press and hold [AUTO] and the down arrow again for 10 seconds.

Adjusting the Screen Image

Use the buttons on the front control panel to display and adjust the on-screen OSD control settings.

• Standby Power On/Off
• Power light
• Green = ON
• Flickering = Power Saving
• [MENU] Displays the Main Menu or exits the control screen and saves adjustments.
• [AUTO] Displays the control screen for the highlighted control. Also a shortcut to toggle analog and digital connection.
• Scrolls through menu options and adjusts the displayed control settings. Blue Light Filter ( ) / ViewMode ( )

Do the following to adjust the display setting:

1. To display the Main Menu, press button [MENU].
   NOTE: All OSD menus and adjustment screens disappear automatically after about 15 seconds. This is adjustable through the OSD timeout setting in the setup menu.

2. To select a control to adjust, press or to scroll up or down in the Main Menu.

3. After the desired control is selected, press button [MENU].

4. To save setting adjustments and exit the menu, press button [AUTO] until the OSD disappears.

The following tips may help you optimize your display:

• Adjust the computer’s graphics card to support a recommended timing mode (refer to “Specifications” page for recommended setting specific to your display). To find instructions on “changing the refresh rate”, please refer to the graphics card’s user guide.
• If necessary, make small adjustments using H. POSITION and V. POSITION until the screen image is completely visible. (The black border around the edge of the screen should barely touch the illuminated “active area” of the display.)

Main Menu Controls

• Navigate through menu items by using the up/down ▲/▼ buttons.
  NOTE: Check the Main Menu items on your display OSD and refer to Main Menu Explanation below.

Main Menu Explanation

• NOTE: The Main Menu items listed in this section indicate whole Main Menu items on all models. For the actual Main Menu details corresponding to your product refer to the items on your display’s OSD Main Menu.

1. A Audio Adjust
   adjusts volume, mutes sound, or toggles between inputs if you have more than one source.

2. Auto Image Adjust
   automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion. Press the [MENU] button to obtain a sharper image.
   NOTE: Auto Image Adjust works with most common video cards. If this function does not work on your display, then lower the video refresh rate to 60 Hz and set the resolution to its pre-set value.

3. B Brightness
   adjusts the background black level of the screen image.

4. C Color Adjust
   provides several color adjustment modes, including preset color temperatures and a User Color mode which allows independent adjustment of red (R), green (G), and blue (B). The factory setting for this product is native.

5. Contrast
   adjusts the difference between the image background (black level) and the foreground (white level).

6. I Information
   displays the timing mode (video signal input) coming from the graphics card in the computer, the display model number, the serial number, and the ViewSonic® website URL. See your graphics card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency).
   NOTE: VESA 1024 x 768 @ 60Hz (example) means that the resolution is 1024 x 768 and the refresh rate is 60 Hertz.

7. Input Select
   toggles between inputs if you have more than one computer connected
   to the display.

8. M Manual Image Adjust
   displays the Manual Image Adjust menu. You can manually set a variety
   of image quality adjustments.

9. Memory Recall
   returns screen settings back to factory settings if the display is operating in a factory Preset Timing Mode listed in the Specifications section of this user guide.
   Exception: This feature does not affect changes made with the Language Select or Power Lock setting.

10. S Setup Menu
    adjusts On-screen Display (OSD) settings.

Power Management

This product will enter into Sleep/Off mode and reduce power consumption within 5 minutes of no signal input.

Other Information

Specifications

Display| Type

Display Size

| TFT (Thin Film Transistor), Active Matrix 1366 x 768 LCD,

0.3 mm pixel pitch Metric: 47 cm

---|---|---
 |  | Imperial: 19” (18.5” viewable)
 | Color Filter| RGB vertical stripe
 | Glass Surface| Anti-Glare
Input Signal| Video Sync| RGB analog (0.7/1.0 Vp-p, 75 ohms)
 |  | Separate Sync
 |  | HDMI (TMDS digital, 100ohms)
 |  | fh:24-82 kHz, fv:50-75 Hz
Compatibility| PC| Up to 1366 x 768 Non-interlaced
 | Macintosh1| Power Macintosh up to 1366 x 768
Resolution 2| Recommended| 1366 x 768 @ 60 Hz
 | Supported| 1280 x 1024 @ 60, 75 Hz
 |  | 1024 x 768 @ 60, 70, 72, 75 Hz
 |  | 800 x 600 @ 56, 60, 72, 75 Hz
 |  | 640 x 480 @ 60, 75 Hz
 |  | 720 x 400 @ 70 Hz
Power| Voltage| 100-240 VAC, 50/60 Hz (auto switch)
Display area| Full Scan| 409.8 mm (H) x 230.4 mm (V)
 |  | 16.1” (H) x 9.1” (V)
Operating| Temperature| +32 °F to +104 °F (0 °C to +40 °C)
conditions| Humidity| 20% to 90% (non-condensing)
 | Altitude| To 10,000 feet
Storage| Temperature| -4 °F to +140 °F (-20 °C to +60 °C)
conditions| Humidity| 5% to 90% (non-condensing)
 | Altitude| To 40,000 feet
Dimensions| Physical| 437.8 mm (W) x 341.9 mm (H) x 170.4 mm (D)
 |  | 17.2” (W) x 13.5” (H) x 6.7” (D)
Weight| Physical| 4.4 lb (2.0 kg)
Power saving| On| 15.3W (Typical) (Blue LED)
modes| Off| <0.5W

1. Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an adapter, contact ViewSonic.
2. Do not set the graphics card in your computer to exceed these timing mode; doing so may result in permanent damage to the display.

Cleaning the Display

• MAKE SURE THE DISPLAY IS TURNED OFF.
• NEVER SPRAY OR POUR ANY LIQUIDS DIRECTLY ONTO THE SCREEN OR

HOUSING.

To clean the screen:

• Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
• If the screen is still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen.

To clean the casing:

• Use a soft, dry cloth.
• If the casing is still not clean, apply a small amount of a non-ammonia, nonalcohol based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.

Disclaimer

• ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the display screen or case. Some chemical cleaners have been reported to damage the screen and/or case of the display.
• ViewSonic will not be liable for damage resulting from use of any ammonia or alcoholbased cleaners.

Troubleshooting

No power

• Make sure the power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the display.
• Plug another electrical device into the power outlet to verify that the outlet is supplying proper voltage.

Power is ON but no screen image

• Make sure the video cable supplied with the display is properly secured to the video output port on the back of the computer. If the other end of the video cable is not attached permanently to the display, properly secure it to the display.
• Adjust brightness and contrast.
• If you are using an Macintosh older than G3, you need a Macintosh adap

Wrong or abnormal colors

• If any colors (red, green, or blue) are missing, check the video cable to make sure it is securely connected. Loose or broken pins in the cable connector could cause an improper connection.
• Connect the display to another computer.
• If you have an older graphics card, contact ViewSonic® for a non-DDC adapter.

Control buttons do not work

• Try pressing only one button at a time.

Customer Support

For technical support or product service, see the table below or contact your reseller.

NOTE: You will need to provide the product serial number.

Country/Region| Website| T= Telephone

C = CHAT ONLINE

| Email
---|---|---|---
Australia New Zealand| www.viewsonic.com.au| AUS= 1800 880 818

NZ= 0800 008 822

| service@au.viewsonic.com
Canada| www.viewsonic.com| T= 1-866-463-4775| service.ca@viewsonic.com
Europe| www.viewsoniceurope.com| www.viewsoniceurope.com/uk/support/call- desk/
Hong Kong| www.hk.viewsonic.com| T= 852 3102 2900| service@hk.viewsonic.com
India| www.in.viewsonic.com| T= 1800 419 0959| service@in.viewsonic.com

| | T= 080 333 2131| service@kr.viewsonic.com
Latin America (Argentina)| www.viewsonic.com/la/| C= http://www.viewsonic.com/la/soporte/servicio-tecnico| soporte@viewsonic.com
Latin America (Chile)| www.viewsonic.com/la/| C= http://www.viewsonic.com/la/soporte/servicio-tecnico| soporte@viewsonic.com
Latin America (Columbia)| www.viewsonic.com/la/| C= http://www.viewsonic.com/la/soporte/servicio-tecnico| soporte@viewsonic.com
Latin America (Mexico)| www.viewsonic.com/la/| C= http://www.viewsonic.com/la/soporte/servicio-tecnico| soporte@viewsonic.com
Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F. Tel: 55) 6547-6454    55)6547-6484

Other places please refer to http://www.viewsonic.com/la/soporte/servicio- tecnico#mexico

Latin America (Peru)| www.viewsonic.com/la/| C= http://www.viewsonic.com/la/soporte/servicio-tecnico| soporte@viewsonic.com
Macau| www.hk.viewsonic.com| T= 853-2840-3687| service@hk.viewsonic.com
Middle East| ap.viewsonic.com/me/| Contact your reseller| service@ap.viewsonic.com
Puerto Rico & Virgin Islands|

www.viewsonic.com

| T= 1-800-688-6688 (English)

C=  http://www.viewsonic.com/la/soporte/servicio-tecnico

| service.us@viewsonic.com soporte@viewsonic.com
Singapore/ Malaysia/ Thailand|

www.ap.viewsonic.com

|

T= 65 6461 6044

|

service@sg.viewsonic.com

South Africa| ap.viewsonic.com/za/| Contact your reseller| service@ap.viewsonic.com
United States| www.viewsonic.com| T= 1-800-688-6688| service.us@viewsonic.com

Limited Warranty

ViewSonic® Display

• What the warranty covers:
  ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.

• How long the warranty is effective:
  ViewSonic displays are warranted for between 1 and 3 years, depending on your country of purchase, for all parts including the light source and for all labour from the date of the first consumer purchase.

• Who the warranty protects:
  This warranty is valid only for the first consumer purchaser.

• What the warranty does not cover:

1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
  * Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.
  * Any damage of the product due to shipment.
  * Removal or installation of the product.
  * Causes external to the product, such as electrical power fluctuations or failure.
  * Use of supplies or parts not meeting ViewSonic’s specifications.
  * Normal wear and tear.
  * Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product for an extended period of time.
4. Removal, installation, one way transportation, insurance, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to Customer Support page). You will need to provide your product’s serial number.
2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.

• Effect of state law:
  This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.
  Sales outside the U.S.A. and Canada:
  For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer. The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject to the terms and conditions of the Maintenance Guarantee Card. For users in Europe and Russia, full details of warranty provided can be found in www.viewsoniceurope.com under Support/Warranty Information.

Mexico Limited Warranty

ViewSonic® Display

• What the warranty covers:
  ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.

• How long the warranty is effective:
  ViewSonic displays are warranted for between 1 and 3 years, depending on your country of purchase, for all parts including the light source and for all labour from the date of the first consumer purchase.

• Who the warranty protects:
  This warranty is valid only for the first consumer purchaser.

• What the warranty does not cover:

  • Any product on which the serial number has been defaced, modified or removed.
  • Damage, deterioration or malfunction resulting from:
  • Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, unauthorized attempted repair, or failure to follow instructions supplied with the product.
  • Any damage of the product due to shipment.
  • Causes external to the product, such as electrical power fluctuations or failure.
  • Use of supplies or parts not meeting ViewSonic’s specifications.
  • Normal wear and tear.
  • Any other cause which does not relate to a product defect.
  • Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product for an extended period of time.
  • Removal, installation, insurance, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim.

For Your Records

Product Name: Model Number: ____ Document Number: Serial Number: ____ Purchase Date: ____ Extended Warranty Purchase? (Y/N)

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.

• Limitation of implied warranties:
  There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose.

• Exclusion of damages:
  ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

  • Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
  • Any other damages, whether incidental, consequential or otherwise.
  • Any claim against the customer by any other party.
  • Repair or attempted repair by anyone not authorized by ViewSonic.

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:

Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México

Tel: (55) 3605-1099   http://www.viewsonic.com/la/soporte/index.htm

NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:| Villahermosa:
Distribuciones y Servicios Computacionales SA de CV.| Compumantenimietnos Garantizados, S.A. de C.V.
Calle Juarez 284 local 2| AV. GREGORIO MENDEZ #1504
Col. Bugambilias C.P: 83140| COL, FLORIDA C.P. 86040
Tel: 01-66-22-14-9005| Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: disc2@hmo.megared.net.mx| E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):| Veracruz, Ver.:
RENTA Y DATOS, S.A. DE C.V. Domicilio:| CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
29 SUR 721 COL. LA PAZ| ENTRE PINZÓN Y ALVARADO
72160 PUEBLA, PUE.| Fracc. Reforma C.P. 91919
Tel: 01(52).222.891.55.77 CON 10 LINEAS| Tel: 01-22-91-00-31-67
E-Mail: datos@puebla.megared.net.mx| E-Mail: gacosta@qplus.com.mx
Chihuahua| Cuernavaca
Soluciones Globales en Computación| Compusupport de Cuernavaca SA de CV
C. Magisterio # 3321 Col. Magisterial| Francisco Leyva # 178 Col. Miguel Hidalgo
Chihuahua, Chih.| C.P. 62040, Cuernavaca Morelos
Tel: 4136954| Tel: 01 777 3180579 / 01 777 3124014
E-Mail: Cefeo@soluglobales.com| E-Mail: aquevedo@compusupportcva.com
Distrito Federal:| Guadalajara, Jal.:
QPLUS, S.A. de C.V.| SERVICRECE, S.A. de C.V.
Av. Coyoacán 931| Av. Niños Héroes # 2281
Col. Del Valle 03100, México, D.F.| Col. Arcos Sur, Sector Juárez
Tel: 01(52)55-50-00-27-35| 44170, Guadalajara, Jalisco
E-Mail : gacosta@qplus.com.mx| Tel: 01(52)33-36-15-15-43
 | E-Mail: mmiranda@servicrece.com
Guerrero Acapulco| Monterrey:
GS Computación (Grupo Sesicomp)| Global Product Services
Progreso #6-A, Colo Centro| Mar Caribe # 1987, Esquina con Golfo Pérsico
39300 Acapulco, Guerrero| Fracc. Bernardo Reyes, CP 64280
Tel: 744-48-32627| Monterrey N.L. México
 | Tel: 8129-5103
 | E-Mail: aydeem@gps1.com.mx
MERIDA:| Oaxaca, Oax.:
ELECTROSER| CENTRO DE DISTRIBUCION Y
Av Reforma No. 403Gx39 y 41| SERVICIO, S.A. de C.V.
Mérida, Yucatán, México CP97000| Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: (52) 999-925-1916| Tel: 01(52)95-15-15-22-22
E-Mail: rrrb@sureste.com| Fax: 01(52)95-15-13-67-00
 | E-Mail. gpotai2001@hotmail.com
Tijuana:| FOR USA SUPPORT:
STD| ViewSonic Corporation
Av Ferrocarril Sonora #3780 L-C| 14035 Pipeline Ave. Chino, CA 91710, USA
Col 20 de Noviembre| Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Tijuana, Mexico| E-Mail: http://www.viewsonic.com

FREQUENTLY ASKED QUESTIONS

What is the aspect ratio of the ViewSonic VA1903H?

Check the aspect ratio, which is the proportional relationship between the width and height of the screen.

What type of panel technology does the ViewSonic VA1903H use?

Identify whether it uses technologies like TN, IPS, or other panel types.

What is the response time of the ViewSonic VA1903H?

Find out the response time, which measures how quickly pixels can change from one color to another.

Does the ViewSonic VA1903H support widescreen viewing?

Confirm if the monitor provides a widescreen aspect ratio for an expanded viewing experience.

What connectivity options does the ViewSonic VA1903H offer?

Determine the available ports for connecting the monitor to devices such as computers or other peripherals.

Is the ViewSonic VA1903H compatible with different operating systems?

Check if the monitor is compatible with popular operating systems like Windows, macOS, or Linux.

Can the ViewSonic VA1903H be mounted on a wall or used with a stand?

Verify if the monitor has VESA mount compatibility or comes with a stand for flexible placement options.

Does the ViewSonic VA1903H have built-in speakers?

Confirm whether the monitor includes speakers for audio playback.

What is the viewing angle of the ViewSonic VA1903H?

Check the horizontal and vertical viewing angles for optimal visibility from different positions.

Is the ViewSonic VA1903H energy-efficient or ENERGY STAR certified?

Verify if the monitor meets energy efficiency standards for reduced power consumption.

Can the ViewSonic VA1903H be used for gaming purposes?

Explore the monitor's suitability for gaming, considering factors like response time and refresh rate.

Does the ViewSonic VA1903H have color calibration options?

Check if the monitor provides color calibration settings for adjusting color accuracy.

What is the recommended resolution for optimal performance on the ViewSonic VA1903H?

Determine the ideal resolution settings to achieve the best visual experience.

Where can I find support, drivers, and firmware updates for the ViewSonic VA1903H?

Visit the official ViewSonic website or contact customer support for access to drivers, firmware updates, and support resources.

DOWNLOAD THE PDF LINK:ViewSonic VA1903H Widescreen Monitor User Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>