VISUAL COMFORT CHO 2456 Stratford Large Bracketed Gas Wall Lantern Instruction Manual
- June 12, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT CHO 2456 Stratford Large Bracketed Gas Wall Lantern
Product Information
The Stratford Large Bracketed Gas Wall Lantern is a stylish and functional outdoor lighting fixture. It is designed to be mounted on a wall bracket and uses gas as a fuel source. The lantern is made of high-quality materials and is built to withstand outdoor conditions.
FOR YOUR SAFETY
DANGER- FIRE OR EXPLOSION HAZARD
If you smell gas:
- Shut off gas to the appliance.
- Extinguish any open flame.
- If odor continues, leave the area immediately.
- After leaving the area, call your gas supplier or fire department.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- Fixtures must be installed at least 3″ from combustible walls and 12″ from combustible ceilings.
- Installation must conform with local codes or, in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1.
Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.
Save these instructions for future reference.
Please contact support@visualcomfort.com
for additional information on obtaining replacement parts.
TOOLS REQUIRED
- Phillips Screwdriver
- Slotted Screwdriver
- Pencil
- Hammer
- Drill
ASSEMBLY INSTRUCTIONS
NOTICE: This light fixture should be installed in accordance with all
applicable, local installation codes, and by a person familiar with the
construction and operation of it, as well as the hazards involved. Inspect
item and contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved
.
-
Carefully remove all parts from the box. Place on a clean, soft surface.
-
Remove mounting plate (C) from fixture (E) by removing screws (F).
-
Using mounting plate (C) as a guide, mark mounting hardware positions and follow mounting hardware instructions to secure mounting plate to wall surface.
Note: Due to various mounting surface types, mounting hardware is not included. Please select proper hardware based on surface application. -
Install glass parts (G) to fixture (E) and secure by bending metal tabs.
-
Open fixture door (I), then install glass parts (K) to fixture (E) and secure by bending metal tabs.
-
Install glass part (H) to fixture door (I) and secure by bending metal tabs, then close fixture door (I).
-
Connect gas tubing (D) from lantern to gas source using proper connection method.
-
Install fixture (E) to mounting plate (C) and secure with screws (F).
-
Double check gas connections and test for leaks before attempting to light lantern.
ADDITIONAL HARDWARE INCLUDED: For your convenience, 3/8” gas adapters and additional 1/4″ flare nut fitting included inside box. Discard if not required.
LIGHTING YOUR LANTERN
- Turn valve (A) to off position before turning on gas supply to lantern. See diagram 1.
- Open door and allow to completely air out.
- With lighter/flame above the burner tip (B), press in and turn valve (A) counter-clockwise approximately 30 degrees until flame appears. See diagram 2.
- Adjust flame to desired height.
Note: Do not operate fixture with gas valve fully open or flame height greater than 3”.
CARE AND MAINTENANCE
MAINTENANCE: CHECK BEFORE EVERY USE
- Keep appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.
- Check burner area to ensure flow of gas or combustion is never obstructed.
- Always ensure proper ventilation before use.
CARE INSTRUCTION
- Allow for item to cool completely before cleaning.
- Use feather duster or soft cloth to clean surface.
- Use damp towel to clean glass.
- No abrasives or chemical agents.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>