SMUG D-THO-4824 Electric Height Adjustable Standing Desk Instruction Manual

Electric Standing Desk
Instruction Manual
D-THO-4824

Specifications

Height Adjustment Range 28.7”–48” (73–122cm)

Step 1 Supplied Parts and Hardware

Step 2 Supplied Parts and Hardware

Step 3   spplied Parts and Hardware

Step 4 Supplied Parts and Hardware

Step 5Supplied Parts and Hardware

Step 6 Supplied Parts and Hardware

Setting the Desk Legs to the Same Height

HEAVY! You may need assistance with this step.

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the right leg. Turn the rod to adjust the right leg so it’s level with the left leg. Turn the rod clockwise to lower the right leg or anti-clockwise to raise it.

Step 1 Setting the Desk Legs to the Same Height

Step 2 Setting the Desk Legs to the Same Height

Step 3 Attaching the Leg Bases
Step 4 Assembling and Attaching the Desktop
Secure the desktop panels with the connectors. Then attach the hooks and controller to the desktop.

Place rubber pads on the desktop screw holes.

Attach the frame to the desktop.

Step 5 Connecting the Cables

Step 6 Installing the Cable Hole Covers

Using the Controller

• Raise the Desk
  Press the button to raise the desk continuously until it reaches the highest position or the button is released.

• Lower the Desk
  Press the button to lower the desk continuously until it reaches the lowest position or the button is released.

• Select Height Setting 1
  Press the button, and the desk will move to the height that was previously set for that button.
  Select Height Setting 2
  Press the button, and the desk will move to the height that was
  previously set for that button.
  Select Height Setting 3
  Press the button, and the desk will move to the height that was previously set for that button.
  Save Current Height Setting
  Short-press the button, and the screen will show. ‘S-’ Press the , , or button to save the current height setting to that button. When you press the , , 2 or button, the desk will move to the height that was previously set for that button. Any button-press will stop the desk.

Settings

• Reset
  Press and hold the button until ‘rst’ is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly.
  Release the button, and reset is complete. If the button is released during the reset procedure, reset will stop. The desk won’t work until reset is done correctly.

• Child Lock
  Press and hold the and buttons together for 5 seconds to turn child lock on. The screen will show ‘LOC’ and the buttons will be disabled. Turn child lock off the same way.

• Settings Menu
  Press and hold the s button for 5 seconds to enter the settings menu. Short- press the Settings Menu Press and hold the s button for 5 seconds to enter the settings menu. Short-press the button to navigate through the menu.
  Short-press the or button to adjust the settings. Long-press the or button to quickly adjust the height settings. Press and hold the button again to save the changes. ‘SUS’ will be displayed if saving is successful (or ‘FAL’ if saving fails). If there is no button-press for 10 seconds, the settings menu will be exited automatically.
  Sbutton to navigate through the menu.
  Short-press the or button to adjust the settings. Long-press the or button to quickly adjust the height settings. Press and hold the button again to save the changes. ‘SUS’ will be displayed if saving is successful (or ‘FAL’ if saving fails). If there is no button- press for 10 seconds, the settings menu will be exited automatically.

• Power-Saving Mode
  The screen will turn offif there is no button-press for a minute. Any button- press will turn the screen on again.

Protection Mode Error Codes

SC0| Standby Overvoltage Protection: Standby voltage too high.
Power off the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
---|---
SC1| Power Supply Overvoltage Protection: Input voltage too high.
If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
SC4| Operating Overvoltage Protection: Operating voltage too high. Power off the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
hot| Overheating Protection: When the motor has been working continuously for too long, it will stop operating to prevent overheating. Wait for at least 18 minutes (until error code disappears) before making any further height adjustment.
r-6| Power Supply Overvoltage Protection (during use): Input voltage too high. Error clears when power supply voltage returns to normal. If error code persists, please contact technical support.
rst| Reset Warning: Continue to complete reset.
E10| Short Circuit Protection: Power off, check the cable connections, and power back on again. If error persists, please contact technical support.
E11| Overloading Protection: Max load exceeded. Error code will persist for 20 seconds (DO NOT operate). Take the things off the desk and confirm there is no mechanical damage
before trying again.
E12| Motor Phase Error Protection: Power off, check the cable connection between the motor and the controller, and power back on again. Then follow the reset instructions. If error code persists, please contact technical support.
E13| Sensor Malfunction Warning: Motor sensor can’t be detected. Power off, check the cable connection between the motor and the controller, and power back on again.
Then follow the reset instructions. If error code persists, please contact technical support.
E14| Anti-Collision System Warning: Impact detected. The desk will move 2″ (50mm) in the opposite direction and stop.
E16| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected. If error code persists, please contact technical support.
E17| Mechanical Failure Warning: Check if there is any structural damage or motor fault.

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>