WORX WX746, WX746.X MarkerX Hot Glue Gun Instructions
- June 4, 2024
- Worx
Table of Contents
WORX WX746, WX746.X MarkerX Hot Glue Gun
PRODUCT SAFETY
GENERAL SAFETY WARNINGS
WARNING Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
This appliance can be used by children aged from 8 years and above and persons
with EN reduced physical, sensory or mental capabil6 ities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.
ADDITIONAL SAFETY INSTRUCTIONS FOR
- GLUE GUNS
- A fire may result if the appliance is not used with care, therefore
- be careful when using the appliance in places where there are combustible materials;
- do not apply to the same place for a long time;
- do not use in presence of an explosive atmosphere;
- be aware that heat may be conducted to combustible materials that are out of sight;
- place the appliance on its stand after use and allow it to cool down before storage;
- do not leave the appliance unattended when it is switched on.
SAFETY WARNINGS FOR BATTERY PACK
- a) Do not dismantle, open or shred cells or battery pack.
- b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by conductive materials. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- c) Do not expose battery pack to heat or fire. Avoid storage in direct sunlight.
- d) Do not subject battery pack to mechanical shock.
- e) In the event of battery leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious EN amounts of water and seek medical advice.
- f) Keep battery pack clean and dry.
- g) Wipe the battery pack terminals with a clean dry cloth if they become dirty.
- h) Battery pack needs to be charged before use. Always refer to this instruction and use the correct charging procedure.
- i) Do not maintain battery pack on charge when not in use.
- j) After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance.
- k) Recharge only with the charger specified by Worx. Do not use any charger other than that specifically provided for use with the equipment.
- l) Do not use any battery pack which is not designed for use with the equipment.
- m) Keep battery pack out of the reach of children.
- n) Retain the original product literature for future reference.
- o) Remove the battery from the equipment when not in use.
- p) Dispose of properly.
- q) Do not mix cells of different manufacture, EN capacity, size or type within a device.
- r) Keep the battery away from microwaves and high pressure.
SYMBOLS
- Read operator’s manual
- Warning
- Wear eye protection
- Wear protective gloves
- Do not burn
- Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem. Do not dispose of waste batteries as unsorted municipal waste.
- Li-Ion battery. This product has been marked with a symbol relating to ‘separate collection’ for all battery packs and battery pack. It will then be recycled or dismantled in order to reduce the impact on the environment. Battery packs can be hazardous for the environment and for human health since they contain hazardous substances.
- Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.
COMPONENT LIST
- NOZZLE
- CAP
- TRIGGER
- GLUE STICK HOLE
- POWER BUTTON
- GLUE STICK
Not all the accessories illustrated or described are included in standard delivery.
TECHNICAL DATA
Type WX746 WX746.X (746 – designation of machinery, representative of glue gun)
| WX746 WX746.X **
---|---
Rated voltage| 20 V Max. *
|
Glue Stick Diameter| 7.2mm
Nozzle Caliber| 1.2 mm
Preheating Time| 25 s
Temperature when heated| 200° C
Runtime(2.0Ah)| more than 120 mins
Machine weight (bare tool)| 0.11Kg
Category| Model| Capacity**
---|---|---
20V Hub/HubX
| WA7160| Input: 20 V 10 A Max.
Output: 20 V 10 A Max.
WA7161
| Input: 20 V 10 A Max.
Output 1: 20 V 10 A Max.
Output 2: 5 V 2 A (USB port)
OPERATING INSTRUCTIONS
NOTE : Before using the tool, read the instruction book carefully.
INTENDED USE
The tool can be used for bonding wood, leather, plastics ,papers and other
materials.
ASSEMBLY
1. Insert the appropriate glue stick for the material being glued via the
hole at the rear of the glue gun.Use 7.2mm mini glue sticks (See Fig. A)
2. Connect the gun and the hub. (See Fig. B)
WARNING : Before operation, make sure the speed control button on the hub is at the “Min” position. (See Fig. C) and the surfaces to be 12 glued must be clean, dry and free of grease. NOTE :The speed control does not work with the glue gun. The speed control is for other tools, such as the MakerX Rotary Tool or Angle Grinder.
OPERATION
-
Confirm the speed control button is set to “Min”. Grasp the tool by the grip. Press the on/off switch on the hub. Then press button on the tool for 3s until the it turns red ,which means the glue gun is heating. When the light turns green, the gun is ready for operation. Press the trigger for gluing. (See Fig. D,E,F) After applying the glue, immediately press the surfaces to be glued together. NOTE : It is recommended to apply the glue on large surfaces or long work pieces in the form of points. On flexible materials, apply in lines.
WARNING : Do not allow the hot glue or the nozzle tip to come into contact with persons or animals.If hot glue contacts with the skin, do not try to remove the glue from the skin,but put the affected area immediately under a stream of cold water for several minutes. -
Press the power button until the light goes out. Then press the on/off switch on the hub to turn off after use.
NOTE : In order to save energy, the glue gun switches off automatically after 10 minutes.
NOTE : Put down the glue gun in a safe way and allow it to cool down completely before packing it away after each use.
MAINTENANCE
Remove the battery before carrying out any adjustment, servicing or
maintenance. There are no user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool. Wipe clean with a dry
cloth. Always store your power tool in a dry place. Keep the motor ventilation
slots clean. Keep all working controls free of dust. Occasionally you may see
sparks through the ventilation slots. This is normal and will not damage your
power tool. Store the accessories in a dry place.
WARNING : Do not use inflammable solvents for cleaning the surfaces to be glued. For excess hardened glue, it can be removed with a blunt object. Do not use solvent for cleaning.
TROUBLESHOOTING
Problems| Possible Causes| Possible Solution|
__**EN**
---|---|---|---
No glue comes out| Glue stick is used up. Glue stick diameter is too large or
small.
Glue stick is not pushed to the end.
| Insert a new glue stick. Use recommended glue sticks.
Push the glue stick to the end when loading.
| 13
Glue stick falls out from the tool.| Glue stick diameter is too small.| Use
recommended glue sticks.
There is glue leaking out without trigger pressed after use.| The temperature
is still high in short time after use and will cause glue melted.| It is
normal and will stop leaking out when the glue gun cools down.
Trigger is blocked for glue escaping toward the rear.| Glue stick diameter too
small.
Glue stick’s melting temperature is too low.
| Use recommended glue sticks.
Glue does not flow evenly.| Glue stick’s melting temperature is too low. Glue
is not heated long enough.
Trigger is not pressed uniformly.
| Wait for heating.
Allow the glue gun time to heat up.
Press trigger slowly and uniformly.
ENVIRONMENTAL PROTECTION
Waste electrical products must not be disposed of with household waste. Please
recycle where facilities exist. Check with your local authorities or retailer
for recycling advice.
DECLARATION OF CONFORMITY
We, Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany On
behalf of Positec declare that the product Description 20V Hot Glue Gun Type
WX746 WX746.X(746-designation of machinery, representative of glue gun)
Function: Gluing
Complies with the following Directives:
2014/30/EU, 2011/65/EU & (EU)2015/863
Standards conform to
EN 60335-1, EN 60335-2-45, EN 62233, EN 55014-1, EN 55014-2
The person authorized to compile the technical file,
Name Marcel Filz
Address Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany
2021/05/10 Allen Ding Deputy Chief Engineer,Testing & Certification Positec Technology (China) Co., Ltd 18, Dongwang Road, Suzhou Industrial Park, Jiangsu 215123, P. R. China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>