Di Si X1 Magnetic Golf Speaker User Manual
- June 14, 2024
- Di Si
Table of Contents
X1
Magnetic Golf Speaker
1. Accessory
ο 3.5mm Audio
Cable
Lifting rope 60CM o Type-C Charging Cable
2. Illustration
- Power ON/OFF/TWS
- Play/Pause/Answer or Reject Phone call
- Volume -/Previous Track
- Volume +/Next Track
- Charging Port
- Micro SD Port
- AUX IN
3. Parameter
| Bluetooth Version | V4.2 |
|---|---|
| Rated Power | 10W(RMS) |
| Waterproof | IPX7 |
| Battery Capacity | Built-in 2000 |
| Power Supply | DC 5V/1A |
| Frequency Response | 115Hz-15KH |
| Receiving Range | ≤3 0M(Open Field) |
| Driver Unit | 40Ω 5W/50m |
| Charging Port | Type-c |
| Playing Time | UP to 10 hours |
| Charging Time | 3 hours |
2. After power ON the speaker, quick press 2 times will shift to TWS mode
4. Function Key
Key
| Operation|
Function
---|---|---
|
ON/OFF/TWS
| 1.Short press to tam on
2. After power ON the speaker, quick press 2 times will shift to TWS mode
Long press for 3 seconds to tam off.
Long press for 8 seconds to reset.
|
Play/pause
| 1. Press once when music is playing/pause, answer incoming call or hand up
a phone call.
2. Press and hold for 2 seconds to reject the incoming call.
3. Hold for 3 seconds to disconnect Bluetooth
|
Volume- /Previous Track
| 1. Press once to decrease to volume
2. Hold for 2 seconds to previous track
|
Volume+/Next Track
| 1. Press once to increase to volume
2. Hold for 2 seconds to next track
5. LED indicator:
- Blue LED blinks when the speak waiting for connection, and turns solid blue after Bluetooth connected successfully.
- Red LED turns solid red when the speaker is recharging, and turns off after the battery fully recharged
- The yellow light on the top of the speaker is a matching mdicator ,Slow flash means enter m to the matching mode ,long brightness means the matching is success
6. Bluetooth Pairing:
- Power on speaker the blue LED will blinks, go to Bluetooth setting on your device, find X1 and select to pair.
7. Micro SD/AUX Mode:
- Max support reading 64GB Micro SD card
- Insert any Micro SD card, the speaker will playing the audio files in the Micro SD card automatically.
- Insert the 3.5mm audio cable, the speaker will shift to AUX mode.
FCC warning statements:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, usesr and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
That is TWS ?
TWS means ture wireless stereo. Let’s say two Bluetooth speakers are able to be paired and playing music synchronously.
How to pair your device?
- Please make sure these two speakers to be paired disconnect from your bluetooth device before you turn them on. Then please turn on two speakers
- Select any one of speaker and double click the POWER key. You will hear a remind sound and yellow LED light will blinking, the speaker is waiting for TWS paring.
- When enter into the matching mode with the voice prompt , the yellow light on the two speakers will be bright in the mean time the light control on the main-speaker is normal and the yellow light brighting on the sub-speaker
- Select the searching mode on your device ,When your device finds “X3 Pro”, select it and connect.
- They will perform as the stereo sounding system.
- Once the speakers are well paired at the first time, they will be automatically paired next time without the above pairing operation.
- If the speaker used to be paired, it is suggested to press “MODE” button for 5 seconds to forcibly cut off the power. Then restart and have the same speaker re-paired with the required new speaker according to the above instruction item 1-item 5.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>