VESTLAND PLCSD Sit Stand Corner Desk Electrically Adjustable Instruction Manual

VESTLAND PLCSD Sit Stand Corner Desk Electrically Adjustable Instruction Manual

Scan QR-code for installation video

min. 710mm-max. 1180mm

100kg(220lbs)

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warmings, please contact your local distributor for assistance

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury. Mounts must be attached as specified in assembly instructions.

• Improper installation may result in damage or serious personal injury.
• Safely gear and proper tools must be used. This product should only be installed by professionals.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Checklist and Installation

Screw List

• M-A x12

• M-B x8

• M- C x32

• M-D 5mm Allen K ey

• Phillips Screw Driver (Not include)

Installation video

Scan QR-code for installation video

SCAN ME

Installations Instructions

TECHNICAL SPECIFICATIONS

ADVANCED SETTING

Press the “ S ” button for 5 seconds until the LED ashes. The menu contains 7 items as the table below . Short press the “ S ” button to select the item you’d like to set, then use the “ / ” buttons to adjust the value. Long press the “ S ” button to save the setting and a progress bar will appear . “SUS” will be displayed if it is saved successfully, and “FAL” will be displayed if it fails. The menu will return to the display height automatically if no operation within 10 seconds.

PROGRAMMING INSTRUCTIONS

MEMORY SETTINGS

Save up to four commonly used desk heights and recall them quickly .

1. Use the UP or DOWN button to move the desk to the desired height.
2. Press the “S”button.
3. Press the “1, 2, or 3”button to assign the current height to a number on the handset.
4. To bring the desk back to any of those assigned heights, press the numbered button.

HANDSET LOCK

The handset can be locked to prevent accidental activation or movement of the desk and to prevent desk
settings from being accidentally changed by children or coworkers

TO LOCK: Press and hold the “ ” and ” ” buttons simultaneously for 5 seconds until the LED reads “Loc”.
TO UNLOCK: Press and hold the “UP” and” Down” buttons simultaneously for 5 seconds until the LED switches from “Loc” to the height display

TROUBLESHOOTING

If your desk does not respond when you tr yo raise it or lower it, or if the handset displays error messages, check to make sure all the cables are secure(Legs to cables, cables to Control box). If the problem persists, perform the reset procedure below

RESET PROCEDURE

1. Unplug the power cord and hold the “ S ” button on the Handset for 30 seconds.
2. Plug the power cord back in.
3. Hold the “ ****“ button until the desk reaches its lowest height, then release. Hold the “ ”button again for about 10 seconds until the desk lowers a bit more, then slightly rises and stops then release.
4. The handset will then display the current height, and you should be able to operate the desk.
5. You may also need to do this if the desktop is ever unplugged or loses power .

If the error message persists af ter performing the Reset procedure, contact us or local distributors to get support.

the Control Box
Abnormal Power Supply Board| SC1| Power on again. If the code persists, replace the Control Box
Abnormal Memory| SC2| P ower on again. If the code persists, replace the Control Box
Collision Protection by Sensor| R-2| The desktop will stop and retract 5cm(2”)
Overheated| HOT| Let the desk rest for 18 minutes
Communication Failure| R-5| Check the connection between Handset and Control Box or replace Handset
Abnormal Voltage| R-6| Power on again. If the code persists, replace the Control Box
Mechanical Failure| R-8| Perform Reset procedure. If the code persists, replace the Leg
Rest not completed| RST| Perform Reset procedure
Short Circuit| EX0| Power on again. If the code persists, replace the Control Box
Overload| EX1| Reduce the load on desk
Wrong Running Direction| EX3| Perform Reset procedure. If the code persists, replace the Leg
Collision Protection| EX4| Perform Reset procedure. If the code persists, replace the Leg
Motor Stalling| EX5| Perform Reset procedure. If the code persists, replace the Leg
Disconnections of Motor Cable| EX6| Check the connection between leg and control box
Remarks: X means 1(the rst leg), 2(the second leg), 3(the third leg)

In the event of a power outage or if the power cord is unplugged, a manual reset may be necessary (see Reset Instructions above)

This product is designed with a duty cycle of 10% (2 min. On, 18 min. o)

Keep Children away from electric height-adjustable desks, control units and handsets.
There is a risk of injur y and electric shock

Do not open any of components: lifting columns, control box, or handset.
There is a danger of electric shock

Keep all electrical components away from liquids

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>